2008 DODGE SPRINTER brake

500 Practical hintsDisplay messages
5
k
Visit
workshop
WARNING
G
ASR has been deactivated due to a malfunc-
tion. Cruise control is also switched off as a
result.
The engine power output may then be lower.
\1Continue driving, but with even greater
care.
\1Have the system checked at an authorized
Sprinter Dealer as soon as possible.
WARNING
G
BAS has been deactivated due to a malfunc-
tion.
The brake system continues to function with
the normal braking effect but with no elec-
tronic support.
\1Continue driving, but with even greater
care.
\1Have the system checked at an authorized
Sprinter Dealer as soon as possible.
Display symbol
Display message
Possible cause / result
Possible solution
nf_BA.book Page 500 Friday, January 25, 2008 3:53 PM

501 Practical hints
Display messages
5
k
unavailable
ASR as well as BAS have been switched off
due to undervoltage.
The battery may not be being charged.
The brake system is still available with the
normal braking effect.
\1Continue driving, but with even greater
care.
\1Have the system checked at an authorized
Sprinter Dealer as soon as possible.
ì
Please enter PIN:
You have not yet entered your details in the
telephone.
\1Enter the PIN for your SIM card.
<
Seatbelt sys.
Visit
workshop
WARNING
G
The belt system has malfunctioned.
\1Have the system checked at an authorized
Sprinter Dealer as soon as possible.
Display symbol
Display message
Possible cause / result
Possible solution
nf_BA.book Page 501 Friday, January 25, 2008 3:53 PM

503 Practical hints
Display messages
5
.
Low beam left
The left-hand low-beam headlamp is mal-
functioning.
\1Change the bulb as soon as possible.
Low beam right
The right-hand low-beam headlamp is mal-
functioning.
\1Change the bulb as soon as possible.
Turn signal left
The left-hand turn signal is malfunctioning.
\1Change the bulb as soon as possible.
Turn signal right
The right-hand turn signal is malfunctioning.
\1Change the bulb as soon as possible.
Brake lamp left
The left-hand brake lamp is malfunctioning.
\1Change the bulb as soon as possible.
Brake lamp right
The right-hand brake lamp is malfunctioning.
\1Change the bulb as soon as possible.
Third brake lamp
The third brake lamp is malfunctioning. This
message will only appear if all LEDs have
failed.
\1Visit an authorized Sprinter Dealer as soon
as possible.
High beam left
The left-hand high-beam headlamp is mal-
functioning.
\1Change the bulb as soon as possible.
Display symbol
Display message
Possible cause / result
Possible solution
nf_BA.book Page 503 Friday, January 25, 2008 3:53 PM

525 Practical hints
Changing bulbs
5
\3 Changing bulbsBulbs and lights are an important aspect
of vehicle safety. For this reason, make
sure that all bulbs are in working order at
all times.\4
Switch off the lights to avoid a short
circuit.
\4
Only touch new bulbs with a clean
lint-free cloth or something similar.
Do not work with wet or greasy fin-
gers.
\4
Only fit 12 V bulbs of the same type
as before and of the correct wattage.
\4
Have the headlamp setting checked
regularly.
\4
If the newly installed bulb does not
light up either, visit an authorized
Sprinter Dealer.
\4
Have the following LEDs and bulbs
changed at an authorized Sprinter
Dealer:\4
The additional turn signals in the
exterior mirrors
\4
The third brake lamp (cargo and
passenger vans only)*
\4
The bi-xenon headlamps*
\4
The foglamps*
Before changing bulbs
Warning
G
Bulbs and bulb holders can become very
hot. For this reason, allow the light to cool
down before changing the bulb.
Keep bulbs out of the reach of children.
Never use a bulb which has been dropped.
Such a bulb may explode and injure you.
H7 bulbs are pressurized and may ex-
plode when changed. You should there-
fore wear eye protection and gloves when
you are changing them.
nf_BA.book Page 525 Friday, January 25, 2008 3:53 PM

530 Practical hintsChanging bulbs
5
Panel van/crewbusExample illustration of chassisRear bulbs
N82.10-2529-31
Bulb
Model
1
Third brake lamp
LED
2
Brake lamp
P21W
3
Turn signal
PY 21 W
4
Tail lamp /
side marker/Stand-
ing lamp (Canada
only)
R5W
5
License plate lamp
W5W
6
Rear foglamp (driv-
er’s side)
P 21 W
7
Reverse lamp
P 21 W
nf_BA.book Page 530 Friday, January 25, 2008 3:53 PM

531 Practical hints
Changing bulbs
5
Changing the rear bulbs (van /crewbus)\1
Switch off the lighting.
Rear lamp units1Securing screws
\1
Undo screws
1
and remove the rear
lamp unit in the direction of the ar-
row.
\1
Remove the connector.
Bulb
Model
8
Perimeter lamp/side
marker
R5W
9
Turn signal
PY 21 W
a
Brake lamp
P21W
b
Reverse lamp
P21W
c
Rear foglamp
(driver’s side)
P 21 W
d
Tail lamp
R5W
e
License plate lamp
R5W
nf_BA.book Page 531 Friday, January 25, 2008 3:53 PM

532 Practical hintsChanging bulbs
5
2Retaining lugs
3Brake lamp
4Side marker, Standing lamp (Canada
only), tail lamp
5Reverse lamp
6Turn signal lamp
7Rear foglamp (driver’s side)\1
Release retaining lugs
2
and re-
move the bulb holder from the rear
lamp unit.
\1
Press down on the bulb, turn it coun-
terclockwise and remove it from the
holder.
\1
Press the new bulb into the bulb
holder and screw it in clockwise.
\1
Plug the connectors into the bulb
holder.
\1
Fit the rear lamp unit.
To do this, clip the bulb holder into
the three holes provided on the side
and tighten screws
1
.
nf_BA.book Page 532 Friday, January 25, 2008 3:53 PM

533 Practical hints
Changing bulbs
5
Changing the rear bulbs (chassis)Example illustration of chassis
1Securing screws
2Lens
3Perimeter lamp, side marker
4Turn signal lamp
5Brake lamp6Tail lamp
7Rear foglamp (driver’s side)
8License plate lamp
9Reverse lamp
\1
Switch off the lighting.
\1
Undo screws
1
and remove lens
2
.
\1
Press the bulb into the bulb holder
and screw it out in a counterclock-
wise direction.
\1
Press the new bulb into the bulb
holder and screw it in clockwise.
\1
Replace lens
2
and retighten
screws
1
.
\1
Switch off the lighting.
Identification lamps W 5 W (cab
chassis only) Changing additional bulbs1Securing screws
2Bulb holder
nf_BA.book Page 533 Friday, January 25, 2008 3:53 PM