Page 120 of 257
1 0 9
IX
D R I V I N G
Park - N e v e r s e l e c t p o s i t i o n Nif the vehicle is moving.
- N e v e r s e l e c t p o s i t i o n s Por Ror if the vehicle is not completely stationary.
If, while the vehicle is moving, position N is engaged inadvertently, let the engine idle before engaging position D or M or.
Do not engage until the vehicle is completely stationary.
To avoid any movement of the vehicle when parked, select positionP a n d a p p l y t h e h a n d b r a k e fi r m l y . C h e c k t h a t t h e s e l e c t o r i s i n t h e Pposition to ensure that the driving wheels are locked.
Reverse gear
Do not engage until the vehicle is stationary, foot on brake. To avoid engine hesitation, do not accelerate immediately after the selection.
Neutral
Do not select this position, even momentarily, when the vehicle is in motion.
Page 123 of 257
1 1 2
IX
D R I V I N G
This driving assistance device allows you to select a maximum speed that you wish not to exceed. This has to b e a s p e e d g r e a t e r t h a n 3 0 k m / h ( a p p r o x . 2 0 m p h ) .
The speed limiter controls are located on the steering wheel.
Note: The information relating to the limiter is displayed in zone A of the instrument panel.
To select the function
Turn control 1 to position "LIM".
On selection of the function, the last speed memorised and the information "OFF" will appear:
To adjust the maximum speed
Provided the engine is running, you can adjust the memorised maximum speed, with short or long presses on:
- b u t t o n 4 to increase the memorised maximum speed,
- b u t t o n 2 to decrease the memorised maximum speed.
Note: successive presses modify the memorised speed in steps of 1 k m / h ( 1 m p h ) , a c o n t i n u o u s p r e s s i n s t e p s o f 5 k m / h ( 3 m p h ) .
Activation of the maximum speed
When the desired maximum speed is displayed, press button 3 to activate the limitation.
The information "OFF" then disappears from zone A.
While the function is active, pressing the accelerator pedal will not enable you to go beyond the programmed speed unless you press the pedal hard down past the tight spot (see "Temporary exceeding of the maximum speed").
Note: The vehicle speed may vary slightly from that memorised.
SPEED LIMITER
Page 128 of 257
117
X
M A I N T E N A N C E
PETROL ENGINES
T h e y g i v e a c c e s s f o r c h e c k i n g t h e l e v e l s o f t h e v a r i o u s fl u i d s a n d t h e r e p l a c e m e n t o f c e r t a i n i t e m s .
1. Power steering reservoir.
2. Screen and headlamp wash reservoir.
3. Engine coolant.
4. B r a k e fl u i d r e s e r v o i r .
5. Battery.
6. Fusebox.
7. A i r fi l t e r * .
8. Engine oil dipstick.
9. Topping up engine oil.
* D e p e n d i n g o n e n g i n e .
Page 129 of 257
118
X
M A I N T E N A N C E
DIESEL ENGINES
T h e y g i v e a c c e s s f o r c h e c k i n g t h e l e v e l s o f t h e v a r i o u s fl u i d s , t h e r e p l a c e m e n t o f c e r t a i n i t e m s a n d p r i m i n g t h e f u e l s y s t e m .
1. Power steering reservoir.
2. Screen and headlamp wash reservoir.
3. Engine coolant.
4. B r a k e fl u i d r e s e r v o i r .
5. Battery.
6. Fusebox.
7. A i r fi l t e r * .
8. Engine oil dipstick.
9. Topping up engine oil.
10. P r i m i n g p u m p * .
11. B l e e d s c r e w * .
* D e p e n d i n g o n e n g i n e .
Page 130 of 257
119
X
M A I N T E N A N C E
A i r fi l t e r
Follow the recommendations in the Maintenance Guide.
When working under the bonnet, when the engine is hot (even stopped and the ignition switched off), the cooling fan coul d operate at any time.
Check the engine oil level frequently between routine service visits, as well as prior to long journeys.
Engine coolant
The coolant level should be between the MAX and MINmarks on the header tank.
If the engine is hot, wait 15 minutes.
Quality: See "Maintenance Guide"
Never work on the cooling system if the engine is hot.
12 volt battery
See "Practical advice".
Engine oil
Check the oil level with the vehicle parked on level ground, after the engine has been switched off for at least fi f t e e n m i n u t e s .
Quality: See "Maintenance Guide"
B r a k e fl u i d
T h e fl u i d l e v e l m u s t b e situated within the MAX and MIN marks visible on the reservoir.
T h e s c r e e n w a s h fl u i d s h o u l d b e replaced periodically as it loses its effectiveness over time.
Quality: See "Maintenance Guide"
If the warning lamp comes on while you are driving, stop immediately and contact the CITROËN network.you are driving, stop immediately stop immediately
D u s t fi l t e r / o d o u r fi l t e r (active carbon)
See "Maintenance Guide"
Take out the oil dipstick.
The level must be between the MAX and MIN marks on the dipstick
It should never exceed the maximum mark.
Windscreen, rear screen and headlamp washer fl u i d
It is recommended that you use products approved by CITROËN.It is recommended that you hat you
S c r e e n w a s h fl u i d r e s e r v o i r : 3.5 litres.
Screen and headlamp wash reservoir: 6.5 litres.
S p e c i fi c a t i o n f o r t h e fl u i d
To ensure optimum cleaning and to a v o i d f r e e z i n g , t o p p i n g u p o r fi l l i n g of the reservoir must not be done with just water.
MAX
MIN
LEVELS
Page 131 of 257
120
X
M A I N T E N A N C E
Radiator - coolant
The coolant must only be checked or topped up if the power unit is cold.
Engine hot
As the cooling system is pressurised, wait for at least one hour after switching off the engine before intervening.
To avoid the risk of scalding, slacken the cap two turns to allow the pressure to escape. Once the pressure has fallen, remove the cap and top up the level.
Adding engine oil
Remove the dipstick before topping up. C h e c k t h e l e v e l a f t e r fi l l i n g .
It should never exceed the maximum mark.
Screw on the cap before closing the bonnet.
Quality: See "Maintenance Guide".
Topping up the cooling system
The coolant level should be between the MAX and MINmarks on the header tank.
Top up the level. If you have to add more than 1 litre, you should have the cooling system checked by CITROËN.the cooling the cooling
Make sure that the cap is on correctly
Note: The necessity to top up frequently would indicate a malfunction that should be checked at the earliest opportunity.
Note: On vehicles equipped with a p a r t i c l e fi l t e r , t h e c o o l i n g f a n m a y operate for some ten minutes after the engine has stopped.
LEVELS
Page 132 of 257
121
X
M A I N T E N A N C E
Windscreen and rear screen w a s h e r fl u i d
For best results as well as for your safety, use only CITROËN approved products which protect at temperatures as low as -25 °C to -30 °C.
I t i s e s s e n t i a l t o h a v e s u f fi c i e n t s c r e e n w a s h fl u i d i f y o u r v e h i c l e i s equipped with Xenon headlamps.
T o c h e c k t h e l e v e l , p l a c e a fi n g e r on aperture A before removing the cap.
Capacity: 3.5 litres.
Capacity with headlamp washers: 6.5 litres.
B r a k e fl u i d
T h e s y n t h e t i c fl u i d n o t o n l y g i v e s protection against corrosion but also ensures correct functioning of the braking system in all environmental conditions, therefore you should only use the synthetic product recommended by the CITROËN only use the synthetic product product
n e t w o r k . ( t h i s fl u i d m u s t b e r e p l a c e d every two years).
These important requirements are detailed in your vehicle’s Maintenance Guide.
Quality: See "Maintenance Guide".
When working under the bonnet, when the engine is hot (even stopped and the ignition switched off), the cooling fan coul d operate at any time.
B r a k e fl u i d r e s e r v o i r
Check and top up at regular intervals.
T h e fl u i d l e v e l m u s t b e s i t u a t e d w i t h i n the max and min marks visible on the reservoir.
If the warning lamp comes on when driving, stop as quickly as possible and contact a CITROËN dealer.driving, stop as quickly as possible quickly
Page 133 of 257
122
X
M A I N T E N A N C E
Protection cover
HDi 135 and 140 engines
Remove the protection cover by fi r s t u n c l i p p i n g p o i n t 1, then 3 and4 . D e t a c h p o i n t 2 by pulling towards you, then lift.
To reposition the protection cover, attach point 2 fi r s t . L o w e r t h e c o v e r , keeping it centred. Clip points 1 and4, pushing vertically and slightly rearwards. Clip point 3 pushing down vertically.
HDi engines are of a highly technical nature.
A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s which only your CITROËN Dealer can guarantee. A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s
Bleeding of water from the diesel f u e l fi l t e r
To be bled on a regular basis (at every oil change).
To evacuate the water, slacken the bleed screw or the water in diesel fuel sensor, which is located at the b a s e o f t h e fi l t e r , u n t i l w a t e r c e a s e s t o fl o w o u t .
Then retighten the bleed screw or the water in diesel fuel sensor.
DIESEL INJECTION EQUIPMENTWear of brake discs, brake pads and brake drums
The rate of wear of the brake pads depends on the use of your vehicle (urban use, frequent stops), and on your style of driving or the type of journey.
For information on checking the discs and drums for wear, contact a CITROËN dealer.
After washing the vehicle, brake progressively to dry out the brake linings.
