2008 Citroen C CROSSER DAG ignition

D R I V I N G
VII
114
Programming

 Press button 1 .

 Set the programmed speed by ac-
celerating to the required speed,
then press button 2 “COAST
SET” .
CRUISE CONTROL
The controls of this system are grouped
together on the steering wheel.

1.
“ON/OFF” button: activation / deac-
tivation of the cruise control mode.

2.
“COAST SET” button: storing of a
driving speed and decreasing of the
cruising speed.

3.
“ACC RES” button: increasing of
the cruising speed and recalling of
the stored speed.

4.
“CANCEL” button: switching off of
the cruise control. When you press button
1 , “CRUISE”
indicator light comes on on the instru-
ment panel.
Steering wheel controls Display on the instrument pan
el
The cruise control cannot, in any cir-
cumstances, take the place of the
need to comply with speed limits or
of the vigilance and responsibility of
the driver.
System which permits automatic main-
taining of the vehicle speed at the value
programmed by the driver, without any
action on the accelerator pedal.

The
cruise control is switched on
manually: the vehicle speed must be
25 mph (40 km/h) minimum and sec-
ond gear must be engaged in the case
of a manual gearbox.

The cruise control is switched off
manually, by an action on the brake or
clutch pedal or if the ASC system is trig-
gered.

The programmed speed can be ex-
ceeded temporarily by pressing the ac-
celerator pedal.
To return to the programmed speed,
simply release the accelerator pedal.

Switching off the ignition cancels any
programmed speed value.

C H E C K S
VIII
121
CHECKING LEVELS Brake fluid level To avoid any risk of scalding, unscrew
the cap by two turns to allow the
pressure to drop. When the pressure
has dropped, remove the cap and top
up the level.
Oil level The reading will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
The check is carried out either when
the ignition is switched on using the oil
level indicator on the instrument panel,
or using the dipstick.
Between two oil changes, the con-
sumption should not exceed 0.5 litre
per 600 miles (1,000 km). The brake fl uid level should be
between the “MAX” and “MIN”
marks.
If it is not, check the brake pad
wear.
Draining the circuit
Refer to the servicing booklet for details
of the interval for this operation.
Coolant level
The coolant level must be
measured when the engine is
cold and should be between
the “LOW” and “FULL” marks.
When the engine is warm, the
temperature of the coolant is regulated
by the fan. This can operate with the ig-
nition off.

On vehicles which are fi tted with a
particle emission fi lter, the fan may
operate after the vehicle has been
switched off, even if the engine is
cold.
In addition, as the cooling system is
pressurised, wait at least one hour after
switching off the engine before carrying
out any work. Wash-wipe and headlamp
wash * fluid
Check the fl uid level regularly,
using the gauge.
* According to country.
Draining the engine
Refer to the servicing booklet for details
of the interval for this operation.
In order to maintain the reliability of the
engine and emission control system,
the use of additives in the engine oil is
prohibited.
Oil specifi cation
The oil must correspond to your engine
and conform to the manufacturer’s rec-
ommendations. Fluid specifi cation
The brake fl uid must conform to the
manufacturer’s recommendations and
fulfi l the DOT4 standards.
Draining the circuit
Refer to the servicing booklet for details
of the interval for this operation.
Fluid specifi cation
The coolant must conform to the manu-
facturer’s recommendations.
Fluid specifi cation
This fl uid must conform to the
manufacturer’s recommendations for
optimum cleaning.
Power steering fluid level
Check the fl uid level with the engine at
idle.
Check that the power steering fl uid level
is always between the “MAX” and “MIN”
marks and top up if necessary.
Fluid specifi cation
This fl uid must conform to the
manufacturer’s recommendations.
Check all of these levels regularly and
top them up if necessary, unless other-
wise indicated.
If a level drops signifi cantly, have the
corresponding circuit checked by a
CITROËN dealer.

P R A C T I C A L I N F O R M A T I O N
IX
139
Fascia fuses
The fuse boxes are placed in the lower
part of the fascia behind the enclosed
storage compartment (left-hand side).
Access to the fuses

 Open the cover A ,

 Pull it towards you to extract it,

 Change the fuse (refer to the
corresponding paragraph).
Fuse N° Rating Functions

1 *
30 A Heating.

2 15 A Brake lights, third brake light, built-in systems
interface.

3 10 A Rear fog lamps.

4 30 A Windscreen wipers and wash-wipe.

5 10 A Diagnostic socket.

6 20 A Central locking, exterior mirrors.

7 15 A Audio equipment, telematics, multifunction display,
hands-free kit, rear DVD player.

8 7.5 A Remote control key, air conditioning control unit,
instrument panel, controls bar, steering wheel
controls.

9 15 A Multifunction display, instrument panel.

10 15 A Built-in systems interface.

11 15 A Rear wiper.

12 7.5 A Instrument panel, 4 wheel drive control unit,
air conditioning control panel, ABS control
unit, multifunction display, automatic headlamp
adjustment, heated seats, air bags control unit,
steering wheel angle sensor, sunroof, rear screen
demisting, remote control.

13 - Not used.

14 10 A Ignition switch.

15 20 A Sunroof.

16 10 A Exterior mirrors, audio equipment, telematics, rear
DVD player.

P R A C T I C A L I N F O R M A T I O N
IX
141
Engine compartment fuses
The fuse box is placed in the engine compartment near the
battery (left-hand side).
Access to the fuses

 Open the bonnet (refer to the “Access” section),

 Press on the hook A to release the catch,

 Remove the cover completely,

 Change the fuse (refer to the corresponding paragraph).

 When you have fi nished, close the cover carefully to
guarantee the sealing of the fuse box.
Fuse N° Rating Functions

1 15 A Front fog lamps.

2 7 A Engine ECU 2.4 litre 16 V

3 20 A CVT automatic gearbox ECU, relay
CVT automatic gearbox ECU

4 10 A Horn.

5 7.5A Alternator 2.4 litre 16V

6 20 A Headlamp wash.

7 10 A Air conditioning.

8 15 A Engine ECU 2.4 litre 16 V

9 - Not used.

10 15 A Demisting, wipers.

11 - Not used.

12 - Not used.

13 - Not used.

14 10 A Left-hand main beam headlamp.

15 10 A Right-hand main beam headlamp.

16 20 A Left-hand dipped headlamp (xenon).

17 20 A Right-hand dipped headlamp (xenon).

18 10 A Left-hand dipped headlamp, manual
and automatic headlamp
adjustment.

19 10 A Right-hand dipped headlamp.

20 - Not used.

21 10 A Ignition coils

P R A C T I C A L I N F O R M A T I O N
IX
144
Charging the battery using a
battery charger

 Disconnect the battery from the
vehicle.

 Remove the battery and place it in a
ventilated area.

 Remove the top-up caps and top
up the level with distilled water if
necessary.

 Connect the battery to the charger
observing the instructions for use
provided by the manufacturer and
start charging.

 Disconnect the battery from the
charger and let it cool.

 If necessary, top up the level with
distilled water.

 Clean the top of the battery
carefully.

 Put the top-up caps back in place.

 Check that the terminals and
connectors are clean. If they are
covered with sulphate (whitish or
greenish deposit), remove them
and clean them.

 Reconnect the battery starting with
the positive terminal (+). Do not disconnect the terminals
while the engine is running.
Do not charge the batteries
without disconnecting the
terminals fi rst. Following reconnection of the
battery
Following reconnection of the battery,
switch on the ignition and wait 1 minute
before starting to permit initialisation of
the electronic systems. However, if slight
diffi culties are encountered following this
operation, contact a CITROËN dealer.
Referring to the corresponding section,
you must yourself reinitialise:
- the one-touch electric windows,
- the sunroof,
- the satellite navigation system.
Avoid prolonged contact of the
electrolyte with the skin.
Most of these fl uids are harmful
to health and very corrosive. It is advisable to disconnect the
battery if the vehicle is to be left
unused for more than one month.
The batteries contain harmful
substances such as sulphuric acid
and lead. They must be disposed of
in accordance with regulations and
must not, in any circumstances, be
discarded with household waste.
Take used remote control batteries
and vehicle batteries to a special
collection point.
When charging the battery, it is
normal to observe an increase in
temperature and bubbling of the
electrolyte.
Before disconnecting the battery
Wait 2 minutes after switching off the ig-
nition before disconnecting the battery.
Close the windows, the sunroof, the
doors and the tailgate before discon-
necting the battery.

A U D I O E Q U I P M E N T a n d T E L E M A T I C S
XI
154
YOUR AUDIO-CD SYSTEM

This consists of the following
components:
- a control panel,
- a multifunction display,
- steering wheel audio controls,
- 4 or 6 speakers (according to version),
- a CD changer (according to version),
- auxiliary sockets, located at the rear of the centre console (according to
version),
- a radio aerial, located on the roof at the rear of the vehicle. Steering wheel audio controls

1.
On / Off and selection of the
radio or CD mode

2.
Decreasing of the volume

3.
Increasing of the volume

4.
Search for a higher radio
frequency / Next track / Fast
forwards play

5
.
Search for a lower radio frequency / Previous track / Rewind play
They can be used when the ignition
switch is in the “ON” or “ACC” position.
Switching on
Press button 1 for more than two
seconds.
The last source selected before switching
off comes back into operation.
Selecting the source
Press button 1 .
The source changes in the following
order: FM1 / FM2 / FM3 / MW / LW /
CD / FM1...
Searching in radio mode
Press button 4 or
5 to search for a higher
or lower radio frequency respectively.
While a track is being played,
press button 5 once to return to the
beginning of this track.
Adjusting the volume
Press and hold button
2 or
3 to decrease
or increase the volume respectively.

It allows you to:
- listen to the radio in FM/MW/LW,
- listen to audio CDs (CD-DA, CD- Text, CD-R/RW) or CDs with MP3
fi les. Switching off
Press button 1 for more than two
seconds. Searching in CD mode
Press button
4 or
5 to select the next or
previous track on the CD respectively.
Press and hold button 4 or 5 for fast
forwards or rewind playing of the current
track of the CD respectively.

A U D I O E Q U I P M E N T a n d T E L E M A T I C S
XI
157
GENERAL FUNCTIONS
Switching on Press the “PWR” button.
The last source selected
before switching off resumes
operation.
The audio equipment functions can be
used when the ignition switch is in the
“ON or “ACC” position.
Adjusting the volume Turn the “VOL” dial
respectively to the left to
decrease the volume or to
the right to increase it.
Switching off
Press the “PWR” button again. Setting the audio modes
Press the “SOUND” button
several times; the audio
modes change in the
following order:
SUB PUNCH / TYPE /
FIELD / BASS / MID /
TREBLE / FADER / BALANCE / OFF.
Quick access mode
To access the personalised sound
functions quickly, press and hold
this button, then turn it to reach the
personalised sound setting of your
choice.
Release the button to store the setting.
“Hold” mode
If you press this button for more than
2 seconds in the audio setting mode, the
system switches to “Hold” mode. The
audio mode selected will be retained
until you press this button again for
more than 2 seconds. Selecting the musical ambience
“TYPE”
Turn the “SOUND” dial; the
musical ambiences change
in the following order:
CLASSIC / JAZZ / POP /
ROCK / HIP-HOP.
Once the ambience has
been selected, press the “SOUND” but-
ton to confi rm.
“CLASSIC”: optimises the acoustics to
obtain perfect equalisation of the sound
for classical music.
“JAZZ”: optimises the acoustics to
obtain an ambient sound with speciifc
modulations in the bass, mid tone and
treble for jazz.
“POP”: optimises the acoustics to obtain
clear vocals and modulation of the bass
and treble for pop music.
“ROCK”: optimises the acoustics to
obtain a sound in harmony with the
rhythm which places the emphasis on
the mid tone for rock music.
“HIP-HOP”: optimises the acoustics
to obtain a powerful sound and
accentuation of the bass for hip-hop
music.
If the “TYPE” is changed, the sound
cuts out briefl y.
The audio setting mode is deactivated
when the radio is operated or a CD
is played or after approximately
10 seconds without any action.

A U D I O E Q U I P M E N T a n d T E L E M A T I C S
XI
211
Making a telephone call using a name in the phone book, receiving a call
Using a name in the system’s phone
book
The name must be recorded in the
system’s phone book. 8 - Answer “Yes” or say “No” to
return to step 4.
Redialling the last number Receiving a call
The telephone ring is transmitted on the
speaker by the front passenger’s seat.
If an audio source (CD, radio, ...) is in
operation when the call is received, it is
placed on mute and only the incoming
call is heard.
When the ignition switch is in the ACC
or ON position, the audio system is
activated automatically if an incoming
call is received, even if it was originally
off.
1 - Press the PICK UP button.
At the end of the call, the audio system
returns to its previous status.
1 - Press the SPEAK button.
2 - Say “Call”.
4 - Say the name of the person that you wish to call.
6 - Say the location corresponding to the number that you wish to
call. 1 - Press the SPEAK button.
2 - Say “Redial”.
3 - The system says “Name please”.
5 - If several telephone numbers have
been recorded for this person, the
system says “Do you wish to call
{home}, {work}, {mobile} or
{pager}?”
7 - The system requests confi rmation of the name. 9 - The system says “Call to at
” and makes the call.