2008 CADILLAC STS traction control

If there is a problem detected with StabiliTrak®,a
SERVICE STABILITY SYS message will be displayed
on the DIC. SeeDIC Warnings and Messages on
page 3-80. When this message is displayed, the system
is not operational. Driving should be adjusted
accordingly.
StabiliTrak
®comes on automatically whenever the
vehicle is started. To help assist with directional control
of the vehicle, always leave the system on. StabiliTrak
®
can be turned off, however, by using the TC (traction
control) on/off button. SeeTraction Control System
(TCS) on page 4-6.
If the vehicle is in cruise control when the StabiliTrak
®
activates, the cruise control will automatically disengage.
When road conditions allow you to safely use it again,
you may reengage the cruise control. SeeCruise Control
on page 3-17orAdaptive Cruise Control on page 3-20for
more information.
Enhanced StabiliTrak®
All-wheel-drive (AWD) vehicles with the Active Steering
with Enhanced StabiliTrak®option have an enhanced
computer controlled vehicle stability system that assists
with directional control of the vehicle in difficult driving
conditions. This system coordinates automatic control of
the Active Steering System, the Magnetic Ride Control
Suspension System, and the Brake Control System for
better vehicle performance.During extreme cold temperature conditions, the active
steering function may be temporarily disabled which may
cause the steering wheel to be off set from the center
position while driving straight. This is normal operation
and the vehicle is safe to drive in these cases.
Stability control activates when the computer senses a
difference between the intended path and the direction
the vehicle is actually traveling. Stability control
automatically adjusts the front road wheel steering angle,
modies the suspension stiffness, and selectively applies
braking pressure at any one of the vehicle’s brakes to
help maintain directional control of the vehicle.
When the system activates, a STABILITY SYS ACTIVE
message displays on the Driver Information Center (DIC).
SeeDIC Warnings and Messages on page 3-80You may
also hear a noise or feel vibration in the brake pedal. This
is normal. Continue to steer the vehicle in the direction
you want it to go.
4-9

If the vehicle is in cruise control when Enhanced
StabiliTrak®activates, the cruise control will automatically
disengage. When road conditions allow you to safely use
it again, you may re-engage the cruise control. See
Cruise Control on page 3-17,orAdaptive Cruise Control
on page 3-20for more information.
Enhanced StabiliTrak
®comes on automatically in the
Stability Touring Mode, when the vehicle is started. The
Stability Touring Mode is recommended for normal
driving. Enhanced StabiliTrak
®also has Stability
Competitive Mode that is turned on by pressing the
Traction Control (TC) Button. SeeTraction Control
System (TCS) on page 4-6. This mode is designed to be
used by the performance conscious driver who desires
less stabilty control intervention. SeeCompetitive Driving
Mode (STS-V) on page 4-7. When the Stability Control
Competitive Mode has been activated, traction control
operates in competitive mode and cannot be turned off.
The STABILITY COMPETITIVE MODE message will be
displayed on the DIC. SeeDIC Warnings and Messages
on page 3-80.
When operating your vehicle in the Stability Competitive
Mode, the system provides less stability control
intervention. Driving should be adjusted accordingly.When the stability control Stability Competitive Mode
has been selected, the Active Steering and Magnetic
Ride Control Touring Mode is not available. These
systems are automatically changed to the Performance
Mode, providing more response to road conditions
and quicker steering response. For more information,
see “Active Steering and Magnetic Ride Control
Mode” in the Index of the vehicle’s Navigation Manual.
To assist you with directional control of the vehicle,
always leave the system on. Stability control can
be turned off however, by using the traction control
button. SeeTraction Control System (TCS) on page 4-6.
The STABILITY SYS OFF message will be displayed
on the DIC. SeeDIC Warnings and Messages on
page 3-80.
If there is a problem detected with Enhanced
StabiliTrak
®, the SERVICE STABILITY SYS message
will be displayed on the DIC. SeeDIC Warnings
and Messages on page 3-80. When this message is
displayed, the system is not operating. Driving should be
adjusted accordingly.
4-10

When certain faults or vehicle conditions are detected,
the Stability control will automatically go into a secure
mode and the STABILITY SECURE MODE message will
be displayed on the DIC. When the Stability Secure Mode
is activated, the stability control system will not respond
to driver requests to change the stability mode until the
next ignition cycle or until the vehicle condition or fault is
returned to normal. When the Stability Secure Mode is
activated, you may see other messages, such as
SERVICE STEERING SYS, SERVICE SUSPENSION
SYS or CHECK TIRE PRESSURE on the DIC. When the
Stability Secure Mode is activated, a larger degree of
steering wheel input at low vehicle speeds and a smaller
degree of steering wheel input at high vehicle speeds
may be required. Stability Secure Mode will be activated
if you are using a compact spare tire. SeeDIC Warnings
and Messages on page 3-80andCompact Spare Tire on
page 5-106.
Persistent operation of your vehicle in the STABILITY
SECURE MODE may be an indication that your vehicle
needs to be serviced by the dealer/retailer.
When certain faults are present, the vehicle’s speed may
be limited and the SPEED LIMITED TO XXX message
will be displayed on the DIC. SeeDIC Warnings and
Messages on page 3-80. When the vehicle’s speed is
limited, you may see other messages, such as SERVICE
STABILITY SYS, SERVICE STEERING SYS or
SERVICE SUSPENSION SYS on the DIC. Have your
vehicle serviced by your dealer/retailer.Enhanced StabiliTrak®and Traction
Control Mode Selection
Enhanced StabiliTrak®can be operated in Touring Mode
or Competitive Mode. It can also be turned off. The
traction control button is used to change stability control
modes (Touring, Competitive or Off) as well as to turn
traction control on or off. SeeTraction Control System
(TCS) on page 4-6. The following information describes
the operation of the traction control button for changing
Traction Control and Stability Control Modes.
When you start your vehicle, Stability control comes on
automatically in the Stability Touring Mode.
To change from Stability Touring Mode to Stability
Competitive Mode, press and hold the traction
control button for about three seconds until
the STABILITY COMPETITIVE MODE message is
displayed on the DIC.
To change from Stability Touring Mode to Stability
Off Mode, press and hold the traction control
button for about ve seconds until the STABILITY
SYS OFF message is displayed on the DIC.
The DIC will temporarily display the STABILITY
COMPETITIVE MODE message prior to displaying
the STABILITY SYS OFF message.
4-11

To change from Stability Competitive Mode to
Stability Touring Mode, press the traction control
button briey and the STABILITY TOURING MODE
message will be displayed on the DIC.
To change from Stability Competitive Mode to
Stability Off Mode, press and hold the traction
control button for approximately ve seconds until
the STABILITY SYS OFF message is displayed
on the DIC. The DIC will temporarily display
the STABILITY TOURING MODE message and
then the STABILITY COMPETITIVE MODE
message prior to displaying the STABILITY SYS
OFF message.
To change from Stability Off Mode to Stability
Touring Mode, press the traction control button
briey and the STABILITY TOURING MODE
message will be displayed on the DIC.
To change from Stability Off Mode to Stability
Competitive Mode, press and hold the traction
control button for about three seconds until
the STABILITY COMPETITIVE MODE message is
displayed on the DIC. The DIC will temporarily
display the STABILITY TOURING MODE message
prior to displaying the STABILITY COMPETITIVE
MODE message.
To turn traction control off while in the Stability
Touring Mode, press the traction control button
briey and the traction control system warning light
will come on. SeeTraction Control System (TCS)
on page 4-6.
To turn traction control on while in the Stability
Touring Mode, press the traction control button
briey and the traction control system warning light
will turn off.
Panic Brake Assist
Your vehicle has a panic brake assist system that
monitors the intention of the driver while braking. If the
system senses that the driver has applied hard/fast
pressure to the brake pedal, the system will generate
additional pressure, making it easier for the driver
to maintain brake application. When this happens the
brake pedal will feel easier to push. Just hold the brake
pedal down rmly and let the system work for you.
You may feel the brakes vibrate, or you may notice
some noise but this is normal. The brakes will return to
normal operation after the brake pedal has been
released.
4-12

When stability control activates, the system
automatically adjusts the front road wheel steering
angle, modies the suspension stiffness, and selectively
applies braking pressure at any one of the vehicle’s
brakes to help maintain directional control of the vehicle.
Adjustments to the steering will not be felt in the
steering wheel. SeeEnhanced StabiliTrak
®on page 4-9.
It is recommended that the battery not be disconnected
when the steering wheel is turned from the center
position. If this occurs, the center position of the steering
wheel could be temporarily changed a small amount.
You can continue to operate your vehicle and, after
a short time, the center position of the steering wheel
will return to normal.
Steering Tips
It is important to take curves at a reasonable speed.
A lot of the “driver lost control” accidents mentioned on
the news happen on curves. Here is why:
Experienced driver or beginner, each of us is subject to
the same laws of physics when driving on curves.
The traction of the tires against the road surface makes
it possible for the vehicle to change its path when
you turn the front wheels. If there is no traction, inertia
will keep the vehicle going in the same direction. If
you have ever tried to steer a vehicle on wet ice, you
will understand this.The traction you can get in a curve depends on the
condition of the tires and the road surface, the angle at
which the curve is banked, and your speed. While
you are in a curve, speed is the one factor you
can control.
Suppose you are steering through a sharp curve.
Then you suddenly accelerate. Both control
systems — steering and acceleration — have to do
their work where the tires meet the road. Adding the
sudden acceleration can demand too much of those
places. You can lose control. SeeTraction Control
System (TCS) on page 4-6andStabiliTrak
®System on
page 4-8orEnhanced StabiliTrak®on page 4-9.
What should you do if this ever happens? Ease up on
the accelerator pedal, steer the vehicle the way you
want it to go, and slow down.
Your stability system might be active. SeeDIC Warnings
and Messages on page 3-80andStabiliTrak
®System
on page 4-8orEnhanced StabiliTrak®on page 4-9.
Speed limit signs near curves warn that you should
adjust your speed. Of course, the posted speeds are
based on good weather and road conditions. Under less
favorable conditions you will want to go slower.
If you need to reduce your speed as you approach a
curve, do it before you enter the curve, while the
front wheels are straight ahead.
4-14

Skidding
In a skid, a driver can lose control of the vehicle.
Defensive drivers avoid most skids by taking reasonable
care suited to existing conditions, and by not overdriving
those conditions. But skids are always possible.
The three types of skids correspond to your vehicle’s
three control systems. In the braking skid, the wheels are
not rolling. In the steering or cornering skid, too much
speed or steering in a curve causes tires to slip and lose
cornering force. And in the acceleration skid, too much
throttle causes the driving wheels to spin.
A cornering skid is best handled by easing your foot off
the accelerator pedal.
Remember: Any traction control system helps avoid only
the acceleration skid. If your traction control system is
off, then an acceleration skid is also best handled
by easing your foot off the accelerator pedal.
If your vehicle starts to slide, ease your foot off the
accelerator pedal and quickly steer the way you want
the vehicle to go. If you start steering quickly enough,
your vehicle may straighten out. Always be ready
for a second skid if it occurs.You might see the STABILITY SYS ACTIVE message
on the Driver Information Center. SeeDIC Warnings and
Messages on page 3-80andStabiliTrak®System on
page 4-8orEnhanced StabiliTrak®on page 4-9.
Of course, traction is reduced when water, snow, ice,
gravel, or other material is on the road. For safety, you
will want to slow down and adjust your driving to
these conditions. It is important to slow down on slippery
surfaces because stopping distance will be longer and
vehicle control more limited.
While driving on a surface with reduced traction, try your
best to avoid sudden steering, acceleration, or braking,
including reducing vehicle speed by shifting to a lower
gear. Any sudden changes could cause the tires to slide.
You may not realize the surface is slippery until your
vehicle is skidding. Learn to recognize warning
clues — such as enough water, ice, or packed snow on
the road to make a mirrored surface — and slow down
when you have any doubt.
Remember: Any Antilock Brake System (ABS) helps
avoid only the braking skid.
4-17

Driving in Rain and on Wet Roads
Rain and wet roads can reduce vehicle traction
and affect your ability to stop and accelerate. Always
drive slower in these types of driving conditions
and avoid driving through large puddles and
deep-standing or owing water.
{CAUTION:
Wet brakes can cause accidents. They might
not work as well in a quick stop and could
cause pulling to one side. You could lose
control of the vehicle.
After driving through a large puddle of water
or a car/vehicle wash, lightly apply the brake
pedal until the brakes work normally.
Flowing or rushing water creates strong
forces. Driving through owing water could
cause your vehicle to be carried away. If this
happens, you and other vehicle occupants
could drown. Do not ignore police warnings
and be very cautious about trying to drive
through owing water.
Hydroplaning
Hydroplaning is dangerous. Water can build up under
your vehicle’s tires so they actually ride on the
water. This can happen if the road is wet enough and
you are going fast enough. When your vehicle is
hydroplaning, it has little or no contact with the road.
There is no hard and fast rule about hydroplaning. The
best advice is to slow down when the road is wet.
Other Rainy Weather Tips
Besides slowing down, other wet weather driving tips
include:
Allow extra following distance.
Pass with caution.
Keep windshield wiping equipment in good shape.
Keep the windshield washer uid reservoir lled.
Have good tires with proper tread depth. SeeTires
on page 5-57.
4-19

The Traction Control System (TCS) improves your
ability to accelerate when driving on a slippery road.
Even though you have TCS, slow down and adjust your
driving to the road conditions. Under certain conditions,
you might want to turn the TCS off, such as when
driving through deep snow and loose gravel, to help
maintain vehicle motion at lower speeds. SeeTraction
Control System (TCS) on page 4-6,StabiliTrak
®System
on page 4-8orEnhanced StabiliTrak®on page 4-9,
Rocking Your Vehicle to Get It Out on page 4-26, and
“Winter Tires” underTires on page 5-57.
The Antilock Brake System (ABS) improves your
vehicle’s stability when you make a hard stop on a
slippery road. Even though you have ABS, begin
stopping sooner than you would on dry pavement. See
Antilock Brake System (ABS) on page 4-5.
Allow greater following distance on any
slippery road.
Watch for slippery spots. The road might be ne until
you hit a spot that is covered with ice. On an
otherwise clear road, ice patches can appear in
shaded areas where the sun cannot reach, such as
around clumps of trees, behind buildings, or under
bridges. Sometimes the surface of a curve or an
overpass can remain icy when the surrounding roads
are clear. If you see a patch of ice ahead of you,
brake before you are on it. Try not to brake while you
are actually on the ice, and avoid sudden steering
maneuvers.
If You Are Caught in a Blizzard
If you are stopped by heavy snow, you could be in a
serious situation. You should probably stay with
your vehicle unless you know for sure that you are near
help and you can hike through the snow. Here are
some things to do to summon help and keep yourself
and your passengers safe:
Turn on the hazard warning ashers.
Tie a red cloth to your vehicle to alert police that
you have been stopped by the snow.
Put on extra clothing or wrap a blanket around you.
If you do not have blankets or extra clothing, make
body insulators from newspapers, burlap bags,
rags, oor mats — anything you can wrap around
yourself or tuck under your clothing to keep warm.
4-23