2008 CADILLAC STS sensor

Disabling and Resetting IntelliBeam™
at the Rearview Mirror
IntelliBeam™ can be disabled and reset to the original
factory setting by using the controls on the inside
rearview mirror.
AUTO
3(IntelliBeam™ On/Off):To disable the
system, press this button on the inside rearview
mirror. The IntelliBeam™ indicator turns off and does
not come back on until the IntelliBeam™ button is
pressed again.
When IntelliBeam™ has turned on the high-beams,
pull or push the high-beam stalk. This disables
IntelliBeam™ and the IntelliBeam™ indicator on the
rearview mirror turns off. To re-enable IntelliBeam™,
press the IntelliBeam™ button on the mirror.
A different sensitivity setting is available for dealer
diagnostics. This is done by pushing and holding this
button for 20 seconds until the light ashes three times.
If you accidentally activate this, the vehicle’s setting
automatically resets each time the ignition is turned off
and then on again; otherwise, refer to the text above
for resetting the system.
Cleaning the IntelliBeam™ Light Sensor
The light sensor is
located on the inside
of the vehicle at the
back of the rearview
mirror.
Clean the light sensor window, periodically, using
glass cleaner on a soft cloth. Gently wipe the sensor
window. Do not spray glass cleaner directly on the
surface of the sensor window.
3-36

During that delay, the instrument panel cluster may
not be as bright as usual. Make sure the instrument
panel brightness lever is in the full bright position.
SeeInstrument Panel Brightness on page 3-41.
To operate your vehicle with the DRL off, turn
the exterior lamp control off and then do one of
the following:
Turn the exterior lamp control to the parking
lamp position.
Turn the exterior lamp control to the headlamp
position.
Turn the exterior lamp control from AUTO to
off and back to AUTO.
An AUTOMATIC LIGHTS OFF message will appear
on the DIC, showing that automatic lighting has
been disabled. SeeDIC Warnings and Messages
on page 3-80.
The regular headlamp system should be turned
on when needed.
Light Sensor
The light sensor for the DRL is located on top of
the instrument panel. If the sensor is covered, it will
read dark, and the exterior lamps may come on
when they are not needed.
3-38

Fog Lamps
Use the fog lamps for better vision in foggy or misty
conditions.
The fog lamp controls are located on the turn
signal/multifunction lever.
-(Fog Lamps):The band with this symbol is used to
turn the fog lamps on and off.
The parking lamps must be on for the fog lamps to work.
To turn the fog lamps on, turn the fog lamp band on
the lever up to the dot and release it. The band
will return to its original position.
To turn the fog lamps off, turn the fog lamp band up
to the dot and release it. The band will return to
its original position, and the fog lamps will turn off.
If the high-beam headlamps are turned on, the
fog lamps will also turn off. They will turn back on
again when you switch back to low-beam headlamps.
Some localities have laws that require the headlamps
to be on along with the fog lamps.
Twilight Sentinel®
Twilight Sentinel®can turn your lamps on and off for you.
A light sensor on top of the instrument panel makes the
Twilight Sentinel
®work, so be sure it is not covered.
With Twilight Sentinel®the following will happen:
When it is dark enough outside, the front turn signal
lamps (DRL) will go off, and the headlamps and
parking lamps will come on. The other lamps
that come on with headlamps will also come on.
When it is bright enough outside, the headlamps
will go off, and the front turn signal lamps (DRL)
will come on, as long as the exterior lamp switch
is in the off position.
3-39

Instrument Panel Brightness
Press the center knob on the DIC control panel until
the knob pops out. Then turn the knob clockwise
to brighten the lights or counterclockwise to dim
them. If the knob is turned completely clockwise,
the interior lamps turn on.
Entry Lighting
The entry lighting system turns on the reading and
dome lamps and the backlighting to the exterior lamp
control when a door is opened or if you press the
remote keyless entry transmitter unlock button.
If activated by the transmitter, the lighting will remain
active for about 25 seconds. The entry lighting system
uses the light sensor; it must be dark outside in order
for the lamps to turn on. The lamps turn off about
25 seconds after the last door is closed. They will dim
to off if the ignition is on, or immediately deactivate if
the power locks are activated.
Parade Dimming
This feature prohibits dimming of the instrument panel
displays and backlighting during daylight hours when
the key is in the ignition and the headlamps are on.
This feature operates with the light sensor and is fully
automatic. When the light sensor reads darkness outside
and the parking lamps are active, the instrument panel
displays can be adjusted by turning the instrument panel
brightness knob. SeeInstrument Panel Brightness
on page 3-41for additional information. Base Level Shown,
Uplevel Similar
3-41

AUTO (Automatic):When this button is pressed and
the temperature is set, the system automatically controls
the inside temperature, the air delivery mode, the air
conditioning compressor, and the fan speed. AUTO will
appear on the display next to the fan, mode indicators,
and recirculation indicator if the vehicle has a air
quality sensor.
1. Press the AUTO button.
2. Adjust the temperature to a comfortable setting,
generally, between 70°F (21°C) and 80°F (27°C).
Choosing the coldest or warmest temperature setting
will not cause the system to heat or cool any faster.
If the system is set at the warmest temperature
setting, the system will try to continuously heat the
vehicle and will not adjust the system down as the
vehicle warms up.
In cold weather, the system can start at reduced
fan speeds to avoid blowing cold air into the vehicle
until warmer air is available. The system starts
out blowing air at the oor, but can automatically
change modes as the vehicle warms up to maintain
the chosen temperature setting. The length of
time needed for warm up depends on the outside
temperature and the length of time that has elapsed
since the vehicle was last driven.
3. Wait for the system to regulate. This may take
from 10 to 30 minutes. Then adjust the temperature,
if necessary.You can switch from English to metric units through the
Driver Information Center (DIC). SeeDIC Operation
and Displays on page 3-74.
The air-conditioning system removes moisture from the
air, so some water might drip underneath the vehicle
while idling or after turning off the engine. This is normal.
Manual Operation
yNz(Mode):Pressing the mode switch and
changing the mode cancels automatic operation and
allows the operator to manually select the air delivery
location. Press AUTO to return to automatic operation.
The outboard air outlets always receive airow
regardless of the mode selected. SeeOutlet Adjustment
on page 3-54to change this airow from the outboard
outlets.
To change the current mode, select one of the following:
Y(Vent):This mode directs air to the instrument
panel outlets.
\(Bi-Level):This mode splits the air between
the instrument panel outlets and the oor outlets.
In automatic operation, cooler air is directed to the
upper outlets and warmer air to the oor outlets.
[(Floor):This mode directs most of the air to the
oor outlets with some air directed to the outboard
outlets, and a little air directed to the windshield and
side windows.
3-49

The mode switch can also be used to select the defog
mode. Information on defogging and defrosting can
be found later in this section.
yAz(Fan):Press this switch to increase or
decrease the fan speed. Pressing this switch cancels
automatic operation and allows the operator to manually
select the amount of airow. Press AUTO to return to
automatic operation.
If the airow seems low when the fan speed is at the
highest setting, the passenger compartment air lter
may need to be replaced. For more information,
seePassenger Compartment Air Filter on page 3-55
andScheduled Maintenance on page 6-4.
h(Recirculation):Press this button to control the
air source for the climate control system. If in AUTO
mode, press this button once to select recirculation.
This mode keeps outside air from coming in the vehicle
and recirculates the air in the vehicle. It can be used
to prevent outside air and odors from entering the
vehicle or to help cool the air inside the vehicle
more quickly.
Recirculation is not available in the defrost mode
and shuts off when defog mode is selected. Both of
these features are designed to limit fogging in the
vehicle. If recirculation is selected during defog mode,
it automatically turns off after 10 minutes to limit
problems with fogging.In some conditions, using recirculation for long periods
of time can cause the air inside the vehicle to become
too dry or stuffy. To prevent this from happening,
after the air in the vehicle has cooled, select AUTO to
return to automatic climate control operation or push
the recirculation button again to select outside air.
Press this button a second time to select outside air.
:(Outside Air):This mode forces the system to
pull air from outside the vehicle. It can be used to bring
fresh air into the vehicle.
Air Quality Sensor:Your vehicle could have an air
quality sensor to help limit the climate control system
from pulling in some harmful exhaust fumes from older,
poorly running, or diesel-equipped vehicles that are
driving near you. This sensor, when active, monitors the
air quality in front of your vehicle and switches to air
recirculation when poor quality air is detected outside
your vehicle. Press the AUTO button on the climate
control to activate the air quality sensor. The word AUTO
comes on the center of the climate control display.
While the air quality sensor senses poor quality air,
the recirculation graphic displays.
3-50

Under some conditions, the air quality sensor system
does not operate. In cold weather, the system might
not be active (even if AUTO is displayed) because
of concerns of fogging your windows, which may occur
by activating recirculation mode. Also, the air quality
sensor system does not remain in recirculation mode
for extended periods of time that could cause stuffy
or very dry conditions in the vehicle. Following a poorly
running vehicle for an extended period of time may
not keep recirculation active indenitely.
The air quality sensor does not activate due to organic
odors, like skunk, and may not activate on many
chemical-related odors. If you wish to limit these types
of odors, manually select recirculation. Your vehicle
could also have a charcoal lter that can limit many
odors from being pulled into your vehicle. This
lter needs to be changed periodically. SeeScheduled
Maintenance on page 6-4. The air quality sensor
system does not protect against carbon monoxide (CO),
which you cannot see or smell. SeeEngine Exhaust
on page 2-38.
O(Power Driver’s Temperature):Press the power
button located on the driver’s side of the climate
control panel to turn the entire climate control system
on or off. Turn the knob to increase or decrease
the temperature inside the vehicle.
O(Power Passenger’s Temperature):Press the
power button located on the passenger’s side of
the climate control panel to turn the passenger’s climate
control system on if they wish to have a different
setting than the driver. Turn the knob to increase or
decrease the temperature for the front passenger.
Turning the passenger’s side power button off will not
shut off the climate control system for the passenger.
The system is set to the same setting as the driver.
{(Ventilated Seat):Press this button, to turn
on the driver or passenger’s side ventilated seat,
if the vehicle has this feature. SeeHeated and
Ventilated Seats on page 1-3.
J(Heated Seat):Press this button, to turn on the
driver or passenger’s side heated seat and seatback,
if the vehicle has this feature. SeeHeated and
Ventilated Seats on page 1-3.
^(Air Conditioning):Press this button to manually
turn off the air conditioning compressor. Press AUTO
to return to automatic operation. To limit fogging on
the windshield, the air conditioning compressor
cannot be off while in the defrost mode.
3-51

Sensors
There is a solar sensor located on the instrument panel,
near the windshield.
There is also an interior temperature sensor located
next to the steering wheel on the instrument panel.
These sensors monitor the solar radiation and the air
inside the vehicle, then use the information to adjust
the temperature, the fan speed and the air delivery
system, in order to maintain the selected temperature.The system may also supply cooler air to the side of the
vehicle facing the sun. Do not cover the sensors or the
automatic climate control system will not work properly.
Defogging and Defrosting
Fog on the inside of windows is a result of high humidity
(moisture) condensing on the cool window glass.
This can be minimized if the climate control system
is used properly. There are two modes to clear fog
from the windshield. Use the defog mode to clear the
windows of fog or moisture and warm the passengers.
Use the defrost mode to remove fog or frost from
the windshield more quickly.
yNz(Mode):Press this button until defog appears
on the display.
-(Defog):This mode directs the air between the
windshield and oor outlets with some air supplied to
the outboard panel outlets and side window defogging
outlets. When this mode is selected, the system turns off
recirculation and runs the air-conditioning compressor
unless the outside temperature is at or below freezing.
The recirculation mode is cancelled when the system
enters the defog mode. If recirculation is selected while
in the defog mode, it is cancelled after 10 minutes.
3-52