2008 CADILLAC CTS reset

Tire Pressure
The pressure for each tire can be viewed in the DIC.
The tire pressure is shown in either pounds per square
inch (psi) or kilopascals (kPa). Press the vehicle
information button until the DIC displays Front Tire
PSI (kPa) Left ## Right ##. Press the vehicle information
button again until the DIC displays Rear Tire PSI (kPa)
Left ## Right ##.
If a low or high tire pressure condition is detected by
the system while driving, a message advising you
to check the pressure in a specic tire appears in the
display. SeeInflation - Tire Pressure on page 5-66and
DIC Warnings and Messages on page 3-56for more
information.
Battery Voltage
This display shows the current battery voltage. Your
vehicle’s charging system regulates voltage based
on the state of the battery. The battery voltage may
uctuate when viewing this information on the DIC.
This is normal.
If there is a problem with the battery charging system,
the charging system light illuminates and/or the DIC
displays a message. SeeCharging System Light
on page 3-37,DIC Warnings and Messages on
page 3-56andElectric Power Management on
page 3-21for more information.
Calibrate Compass
Your vehicle may have this feature. The compass can
be manually calibrated. To calibrate the compass
through the DIC, seeDIC Compass on page 3-53.
Change Compass Zone
Your vehicle may have this feature. To change the
compass zone through the DIC, seeDIC Compass on
page 3-53.
Relearn Remote Key
If your vehicle has the Remote Keyless Entry (RKE)
system, this display allows you to match the transmitter
to your vehicle. If your vehicle has the keyless access
system, seeKeyless Access System Operation on
page 2-10for instructions on matching a keyless access
transmitter to your vehicle. To match an RKE transmitter
to your vehicle:
1. Press the vehicle information button until
Press
VTo Relearn Remote Key displays.
2. Press the set/reset button until Remote Key
Learning Active is displayed.
3-52

3. Press and hold the lock and unlock buttons on
the rst transmitter at the same time for about
15 seconds.
On vehicles with memory recall seats, the rst
transmitter learned will match driver 1 and
the second will match driver 2.
A chime sounds indicating that the transmitter is
matched.
4. To match additional transmitters at this time,
repeat Step 3.
Each vehicle can have a maximum of eight
transmitters matched to it.
5. To exit the programming mode, you must cycle
the key to LOCK/OFF.
Blank Display
This display shows no information.
DIC Compass
Your vehicle may have a compass in the Driver
Information Center (DIC).
Compass Zone
The zone is set to zone eight upon leaving the factory.
Your dealer/retailer will set the correct zone for your
location.
Under certain circumstances, such as during a long
distance cross-country trip or moving to a new state
or province, it will be necessary to compensate for
compass variance by resetting the zone through the
DIC if the zone is not set correctly.
Compass variance is the difference between the earth’s
magnetic north and true geographic north. If the
compass is not set to the zone where you live, the
compass may give false readings. The compass must
be set to the variance zone in which the vehicle is
traveling.
3-53

To adjust for compass variance, use the following
procedure:
Compass Variance (Zone) Procedure
1. Do not set the compass zone when the vehicle is
moving. On an automatic transmission vehicle,
only set it when the vehicle is in PARK (P). On a
manual transmission vehicle, only set it when
the vehicle is stopped.
Press the vehicle information button until
Press
VTo Change Compass Zone displays.
2. Find the vehicle’s current location and variance
zone number on the map.
Zones 1 through 15 are available.
3. Press the set/reset button to scroll through and
select the appropriate variance zone.
4. Press the trip/fuel button until the vehicle heading,
for example, N for North, is displayed in the DIC.
5. Calibrate the compass. See “Compass Calibration
Procedure” following.
3-54

Compass Calibration
The compass can be manually calibrated. Only calibrate
the compass in a magnetically clean and safe location,
such as an open parking lot, where driving the vehicle
in circles is not a danger. It is suggested to calibrate
away from tall buildings, utility wires, manhole covers, or
other industrial structures, if possible.
If CAL should ever appear in the DIC display, the
compass should be calibrated.
If the DIC display does not show a heading, for example,
N for North, or the heading does not change after
making turns, there may be a strong magnetic eld
interfering with the compass. Such interference may
be caused by a magnetic CB or cell phone antenna
mount, a magnetic emergency light, magnetic note
pad holder, or any other magnetic item. Turn off
the vehicle, move the magnetic item, then turn on
the vehicle and calibrate the compass.To calibrate the compass, use the following procedure:Compass Calibration Procedure
1. Before calibrating the compass, make sure the
compass zone is set to the variance zone in
which the vehicle is located. See “Compass
Variance (Zone) Procedure” earlier in this section.
Do not operate any switches such as window,
sunroof, climate controls, seats, etc. during
the calibration procedure.
2. Press the vehicle information button until
Press
VTo Calibrate Compass displays.
3. Press the set/reset button to start the compass
calibration.
4. The DIC will display Calibrating Drive In Circles.
Drive the vehicle in tight circles at less than
5 mph (8 km/h) to complete the calibration. The DIC
will display Calibration Complete for a few seconds
when the calibration is complete. The DIC display
will then return to Press
VTo Calibrate Compass.
3-55

DIC Warnings and Messages
Messages are displayed on the DIC to notify the driver
that the status of the vehicle has changed and that
some action may be needed by the driver to correct the
condition. Multiple messages may appear one after
another.
Some messages may not require immediate action, but
you can press any of the DIC buttons on the instrument
panel to acknowledge that you received the messages
and to clear them from the display.
Some messages cannot be cleared from the DIC
display because they are more urgent. These messages
require action before they can be cleared. You should
take any messages that appear on the display seriously
and remember that clearing the messages will only
make the messages disappear, not correct the problem.
The following are the possible messages that can be
displayed and some information about them.
Accessory Mode Active
If your vehicle has the keyless access system, this
message displays when the accessory mode is active.
SeeIgnition Positions (Key Access) on page 2-32
orIgnition Positions (Keyless Access) on page 2-34
for more information.
AFL (Adaptive Forward Lighting)
Lamps Need Service
This message displays when the Adaptive Forward
Lighting (AFL) system is disabled and needs service.
See your dealer/retailer. SeeAdaptive Forward Lighting
System on page 3-19for more information.
All Wheel Drive Off
If your vehicle has the All-Wheel Drive (AWD) system,
this message displays when there is a temporary
condition making the AWD system unavailable.
Your vehicle will run in 2WD. This could be caused by:
Loss of wheel or vehicle speed
AWD system overheat
Certain vehicle electrical conditions
This message turns off when the above conditions are no
longer present and by resetting the warning message.
To reset the warning message, turn the ignition off and
then back on again after 30 seconds. If the message
stays on, see your dealer/retailer right away. See
All-Wheel Drive (AWD) System on page 4-9for more
information.
3-56

Calibrating Drive In Circles
This message displays when calibrating the compass.
Drive the vehicle in circles at less than 5 mph (8 km/h)
to complete the calibration. SeeDIC Compass on
page 3-53for more information.
Calibration Complete
This message displays when the compass calibration is
complete. SeeDIC Compass on page 3-53for more
information.
Change Engine Oil Soon
When this message displays, it means that service is
required for your vehicle. See your dealer/retailer.
SeeEngine Oil on page 5-16andScheduled
Maintenance on page 6-4for more information.
When you reset the Change Engine Oil Soon message
by clearing it from the display, you still must reset
the engine oil life system separately. For more
information on resetting the engine oil life system,
seeEngine Oil Life System on page 5-19.
Check Tire Pressure
This message displays when the pressure in one or
more of the vehicle’s tires needs to be checked.
This message also displays Left Front, Right Front,
Left Rear, or Right Rear to indicate which tire needs
to be checked. You can receive more than one tire
pressure message at a time. To read the other
messages that may have been sent at the same time,
press the set/reset button. If a tire pressure message
appears on the DIC, stop as soon as you can. Have the
tire pressures checked and set to those shown on the
Tire Loading Information label. SeeTires on page 5-58,
Loading the Vehicle on page 4-22, andInflation - Tire
Pressure on page 5-66. The DIC display also shows the
tire pressure values. SeeDIC Operation and Displays
on page 3-48. If the tire pressure is low, the low tire
pressure warning light comes on. SeeTire Pressure
Light on page 3-41.
Cruise Set To XXX MPH (km/h)
This message displays whenever the cruise control is set.
SeeCruise Control on page 3-14for more information.
Driver Door Open
This message displays when the driver door is not closed
completely. Make sure that the door is closed completely.
3-58

Left Rear Door Open
This message displays when the driver side rear door is
not closed completely. Make sure that the door is
closed completely.
Maximum # Electronic Keys Learned
If your vehicle has the keyless access system, this
message displays when the maximum number of
transmitters have been learned. SeeKeyless Access
System Operation on page 2-10for more information.
Oil Pressure Low Stop Engine
Notice:If you drive your vehicle while the engine
oil pressure is low, severe engine damage may
occur. If a low oil pressure warning appears on
the instrument panel cluster and/or DIC, stop the
vehicle as soon as possible. Do not drive the vehicle
until the cause of the low oil pressure is corrected.
SeeEngine Oil on page 5-16for more information.
This message displays when the vehicle’s engine
oil pressure is low. The oil pressure light may also
appear on the instrument panel cluster. SeeOil
Pressure Light on page 3-44. SeeEngine Oil on
page 5-16for more information.Stop the vehicle immediately, as engine damage can
result from driving a vehicle with low oil pressure.
Have the vehicle serviced by your dealer/retailer as soon
as possible when this message is displayed.
Parking Assist Off
If your vehicle has the Ultrasonic Rear Parking Assist
(URPA) system, after the vehicle has been started, this
message displays to remind the driver that the URPA
system has been turned off. Press the set/reset button to
acknowledge this message and clear it from the DIC
display. To turn the URPA system back on, see “Parking
Assist” underDIC Operation and Displays on page 3-48.
SeeUltrasonic Rear Parking Assist (URPA) on
page 2-52for more information.
Passenger Door Open
This message displays when the passenger side front
door is not closed completely. Make sure that the door is
closed completely.
3-62

Service StabiliTrak
This message displays if there has been a
problem detected with the StabiliTrak®system.
The TCS/StabiliTrak warning light on the instrument
panel cluster also comes on.
If this message comes on while you are driving, pull off
the road as soon as possible and stop carefully. Try
resetting the system by turning the ignition off then back
on. If this message still stays on or comes back on
again while you are driving, your vehicle needs service.
Have the StabiliTrak system inspected by your
dealer/retailer as soon as possible. SeeStabiliTrak
®
System on page 4-8for more information.
Service Theft Deterrent System
This message displays when there is a problem with the
theft-deterrent system programmed in the key. A fault
has been detected in the system which means that
the system is disabled and it is not protecting the
vehicle. The vehicle usually restarts; however, you may
want to take the vehicle to your dealer/retailer before
turning off the engine. SeeImmobilizer Operation
(Key Access) on page 2-30orImmobilizer Operation
(Keyless Access) on page 2-31for more information.
Service Tire Monitor System
This message displays if a part on the Tire Pressure
Monitor System (TPMS) is not working properly. The tire
pressure light also ashes and then remains on during
the same ignition cycle. SeeTire Pressure Light on
page 3-41. Several conditions may cause this message
to appear. SeeTire Pressure Monitor Operation on
page 5-70for more information. If the warning comes on
and stays on, there may be a problem with the TPMS.
See your dealer/retailer.
Service Traction Control
This message displays when there is a problem with
the Traction Control System (TCS). The TCS/StabiliTrak
warning light on the instrument panel cluster also comes
on. When this message displays, the system will not limit
wheel spin. Adjust your driving accordingly. See your
dealer/retailer for service. SeeTraction Control System
(TCS) on page 4-6for more information.
Service Transmission
This message displays when there is a problem with the
vehicle’s transmission. Have your vehicle serviced by
your dealer/retailer.
3-66