2008 AUDI S8 wheel

Tires and wheels 11111 --------------------------------------------
•
Wheel bolts
Wheel bolts must al wa ys be tightened to the correc t
tor que .
The design of wheel bo lts is matched to the factory installed rims. If
di fferent r ims a re fitted, t he co rrect w heel bo lts wi th the rig ht len gth
and correct ly shaped bolt heads m ust be used. This ensures that
w he els a re fitt ed se cu rel y and that t he bra ke syste m functi on s
correctly.
In certa in ci rc ums ta nces, yo u may no t use wheel bo lts fr om a
differ ent vehicle - eve n if it is the sa me
model=:> page 382.
& WARNING
Improperly tightened or maintained wheel bolts can become loose
causing loss of control, a collision and serious personal injury.
• Always keep the wheel bolts and the threads in the wheel hubs
clean so the wheel bolts can turn easily and be properly tightened .
• Never grease or oil the wheel bolts and the threads in the wheel
hubs. They can become loose while driving if greased or oiled,
even if tightened to the specified torque .
• Only use wheel bolts that belong to the rim being installed .
• Never use different wheels bolts on your vehicle.
• Always maintain the correct tightening torque for the wheel
bolts to reduce the risk of a wheel loss .
If the tightening torque of
the wheel bolts is too low, they can loosen and come out when the
vehicle is moving . If the tightening torque is too high, the wheel
bolts and threads can be damaged and the wheel can become
loose .
0 Note
The specified torque for the wheel bo lts is 9 0 ft lb (12 0 N m) with a
t olerance o f± 7,4 ft lb(± 10 Nm). T orque whee l bolts diago nally.
After changing a whee l, the torque must be checked as soon as possible with a torque wrench
-preferably by an authorized Audi
dea ler o r qua lif ied wo rksho p.•
Low aspect ratio tires
You r Aud i is fact ory- eq uip pe d w it h lo w aspect rati o tire s. T hese tir es
hav e been thorough ly t ested and been se lect ed specifical ly for your
mod el for thei r supe rb pe rf or manc e, r oad f eel an d ha nd ling under
a variety of driving conditions. As k your authorized Audi d ealer for
m or e de tails.
The low aspect rat io o f th ese t ires is indicat ed by a nume ra l of 55 or
less in the tire's size designatio n. The numeral represents the ratio
o f t he tir e's s idewa ll he ig ht in r ela ti on to it s tread w idt h ex pressed
in percentage . Conventiona l tires have a height/width ratio of 60 or
more.
The performan ce of low -aspe ct-ratio tires is particularly sensitive to
improper inflation pressure . It is therefore important that low
aspect ratio tires are inflated to the specified pressure and that the
inflation pressure is regularly checked and maintained . Tire pres­
sures should be checked at least once a month and alway s before a
long
trip :::::, page 331, "Checking tire pressure" .
What you can do to avoid tire and rim damage L ow a spect ratio tires can be damaged mo re easily by impact with
pot ho les, cu rbs, gull ies o r ridge s o n th e road, part icular ly if th e tire
is underinf lated .
I n or der to mini mize th e occurren ce of i mpac t da mag e to the tires
of your vehicle, we recommend that you observe the fol lowing
pr ecaut ions :
• Alwa ys m aint ain recom mended inflatio n pressu res . C he ck you r
t ire p res su re eve ry 2,000 mi les (3, 000 k m) and add ai r if neces sary .
• D rive carefully on roads with potho les, deep gullies or ridges .
The impac t from d riving th rough or ove r such o bstacles can
da mage you r tir es . Imp act with a curb may a lso caus e damage to
your tire s. .,_
Vehicle care

_______________________________________________ W_ h_ a
_ t_d_ o_ l _d _o_ n_ o_ w_ ? _ __,ffllll
[ i J Tips
If you no longer have your original warni ng triang le and need to
equip your vehic le with a new one, contact you r authorized Audi
d ea ler for a r eplace men t. •
Jack, tools and spare wheel
Jack
The jack is store d unde rnea th the floor panel in the
lug gage co mpartm en t.
Fig . 280 Luggage
c ompartment vehicle
jack
Before s tori ng the jack, make su re i t is wound back down as far as it
wi ll go.
& WARNING
Improper use of the vehi cle ja ck can cause serious personal inju ­
ries .
• Never use the jack supplied with your Audi on another vehi cle,
particularly on a heavier one. The jack is only suitable for u se on
the vehi cle it came with .
& WARNING (continued )
• Using a bumper jack to raise the vehicle will damage the
bumper system . The jack may slip , causing injury.
• Never support your vehicle on cinder blocks , bricks or other
objects. These may not be able to support the load and could
cause injury when they fail.
• Never start or run the engine while the vehicle is supported by
the jack.
• If you must work under the vehicle , always use safety st ands
s pecifically designed for this purpose .
• Never use the he xagonal socket in the handle of the s crew­
driver to loosen or tighten the wheel bolts.
• Always make sure the spare tire and even a flat tire are secured
in place and not loose , otherwise they could fly forward , causing
personal injury to passengers in the v ehicle in an a ccident or
sudden maneuver .
[ i J Tips
Before you can raise your vehicle using the jack, yo u must act ivate
the jack ing mode ::}
page 188. •
Vehicle care Do-it-yourself service irechnical data

llffl!I What do I do novv?
'---------------------------------------------
Tools
The vehicle tools are stored in the luggage compartment
lid.
Fig . 281 Trunk lid:
Opening the cover
Fig . 282 Trunk lid:
Vehicle tools
-To open the cover, turn the retainer in the direction of the
arrow and pull the cover down
~ page 350, fig. 281.
The onboard tool kit includes:
• Hook for removing wheel covers *
• Plastic hook to remove wheel bolt covers
• Whe el bolt wr ench
• Alignment pin for changing wheels
• Screwdr iv e r with reversible blade •
10 x 13 open ended wrench
• Towing loop
[ i] Tips
Some of the on board items listed above are provided on certain
models only or are optional extras .•
Spare wheel
The spare wheel is stored in the wheel well underneath
the floor panel in the luggage compartment.
Fig . 283 Luggage
compartment spare
wheel
Your vehicle is equipped with a regular spare wheel. It is
held in place by plastic retaining knurled screw.
Taking out the spare wheel
- Raise the floor panel at the plastic handle.
- Securely engage the handle in the luggage compartment
seal as illustrated to keep the floor panel up.
- Unscrew the knurled retainer bolt in the wheel center
~ fig. 283. Turn it counter-clockwise .
- Take out the spare wheel.

What do I do now? Ill
------------------~;___
•
-Disengage and lower the floor panel before you close the
luggage compartment lid again.
Storing the replaced wheel
-Place the replaced wheel inside the spare wheel well in
the luggage compartment.
Tighten the knurled retaining screw clockwise to secure
the wheel in place.
-Disengage and lower the floor panel before you close the
luggage compartment lid again.
& WARNING
Loose items in the passenger compartment can cause serious
personal injury during hard braking or in an accident .
• Never store the spare wheel or jack and tools in the passenger
compartment.
• Always store all jacking equipment, tools, and the spare wheel
in the luggage compartment .
• Tighten the knurled retaining screw for the spare wheel
securely.
[ i] Tips
Check the inflation pressure of the spare tire periodically to keep the
tire ready for use. •
Changing a wheel
Before changing a wheel
Observe the following precautions for your own and your
passenger's safety when changing a wheel.
-After you experience a tire failure, pull the car well away
from moving traffic and try to reach level ground before
you stop
~ &,. .
-All passengers should leave the car and move to a safe
location (for instance, behind the
guardrail) ~&,. .
-Engage the parking brake to prevent your vehicle from
rolling
unintentionally ~&,. .
-Move selector lever to position P ~ &,..
-If you are towing a trailer: unhitch the trailer from your
vehicle.
-Take the jack and the spare tire out of the luggage
compartment~ page 349.
& WARNING
You or your passengers could be injured while changing a wheel if
you do not follow these safety precautions:
• If you have a flat tire, move a safe distance off the road. Turn off
the engine, turn the emergency flashers on and use other warning
devices to alert other motorists.
• Make sure that passengers wait in a safe place away from the
vehicle and well away from the road and traffic.
• To help prevent the vehicle from moving suddenly and possibly
slipping off the jack, always fully set the parking brake and block
the wheel diagonally opposite the wheel being changed. When one _..
Do -it -yourself service

-What do I do now? PW-------------------------
&, WARNING (continued)
front wheel is lifted off the ground, placing the Automatic Trans­
mission in
"P" (Park) will not prevent the vehicle from moving.
• Before you change a wheel, be sure the ground is level and firm.
If necessary, use a sturdy board under the jack.
• After installing the spare wheel, make sure that you replace the
flat tire/wheel in its storage area properly and tighten the knurled
retaining screw securely.
[ i] Tips
Before changing the wheel, you must activate the jacking mode, so
that the automatic controls for the Adaptive Air Suspension do not
make it more difficult to lift the vehicle with the
jack ~ page 7 88. •
Changing a wheel
When you change a wheel, follow the sequence described
below step-by-step and in exactly that order.
1. Activate the vehicle jacking mode => page 188.
2. Remove the decorative wheel cover*. For more details
see also
=> page 353, "Decorative wheel covers" or
=> page 353, "Wheels with wheel bolt caps" .
3. Loosen the wheel bolts => page 354.
4. Locate the proper mounting point for the jack and align
the jack below that
point=> page 354.
5. Lift the car with the jack=> page 354.
6. Remove the wheel with the flat tire and then install the
spare
=> page 356 .
7. Tighten all wheel bolts lightly. 8.
Lower the vehicle with the jack.
9. Use the wheel bolt wrench and firmly tighten all wheel
bolts
=> page 354.
10. Replace the decorative wheel cover*.
11. Deactivate the vehicle jacking mode => page 188 .
& WARNING
Always read and follow all WARNINGS and information ~ & in
"Raising the vehicle" on
page 354 and ~ page 357. •
After changing a wheel
A wheel change is not complete without the doing the
following.
-Store and secure the wheel you replaced in the spare
wheel well.
-Replace the tools and the jack in their proper location.
-Check the tire pressure on the spare wheel immediately
after mounting it.
-As soon as possible , have the tightening torques on all
wheel bolts checked with a torque wrench. The correct
tightening torque is 90 ft lb (120 Nm) .
-Have the flat tire replaced as soon as possible.
[ i] Tips
• If you notice that the wheel bolts are corroded and difficult to
turn while changing a tire, they should be replaced before you check
the tightening torque . .,_

What do I do now? -
-----------------
• Drive at reduced speed until you have the tightening torqu es
checked .•
A pplies to vehic les: wi th deco ra tive w heel covers
Decorative wheel covers
The decorative wheel covers must be removed first to
access the wheel bolts.
Removing
Fig . 284 Changing a
wheel: Removing the
wheel cover
-Insert the hook prov ided with the vehicle tool k it in the
hole in the hub.
Pull off the
decorative wheel cover ~ fig. 284. •
A pp lies to veh ic les: w ith whee l bo lts with caps
Wheels with wheel bolt caps
The caps must be removed first from the wheel bolts
before the bolts can be unscrewed .
Removing
Fig. 285 Changing a
wheel: removing the
wheel bolt caps
-Push the plastic clip provided with the veh icle tool kit
over the wheel bolt cap unt il it engages.
-Pull on the plastic clip to remove the cap~ fig. 285.
Refitting
-Place the caps over the wheel bolts and push them back
on.
Th e caps are to pro tect and ke ep the wheel bo lts clean. •
Vehicle care Do-it-yourself service irechnical data

lll'I....__W_ h_ a
_ t_d_ o_ l _d _o_ n_ o_ vv_ ? ______________________________________________ _
Loosening and tightening the wheel bolts
The wheel bolts must be loosened before raising the
vehicle .
Loosening
Fig . 28 6 Chang in g a
w hee l: loos enin g t he
whee l bolts
-Install the wheel bolt wrench over the wheel bolt and
push it down as far as it will go.
Take tight hold of the
end of the wrenc h handle and turn
the wheel bolts counter-clockwise about
one single turn
in the direction of
arrow =:> fig. 286.
Tightening
-Install th e wheel bolt wren ch over the wheel bo lt and
push it down as far as it w ill go .
- Take tight hold o f the
end of th e w re n ch handle and tur n
each wheel bolt clockwi se until it is seated.
& WARNING
• Do not u se fo rc e or hu rry when changi ng a whe el -you c an
ca use th e vehicle to slip off the jack and c ause ser iou s pers onal
injurie s.
& W AR N IN G (c ontinu ed )
• Do not loo sen th e wheel b olt s m ore than one turn before you
rai se the vehicle w ith the jack .
-You ris k an inju ry.
[ i] Tips
• Never use the hexagonal socket in the handle of the screwdriver
to loosen or tighten the wheel bolts .
• If a wheel bo lt is very tight, you may find it easier to loosen by
carefully pushing down on the end of the wheel bolt wrench with
one foot only . As you do so, hold on to the car to keep your balance
and take care not to slip. •
Raising the vehicle
The vehicle must be lifted with the jack first before the
wheel can be removed.
Fig . 287 C ha ng ing a
w he el: m ounting
poi nts for th e jac k ..

What do I do now? -
-----------------
Fig. 288 Clos e-up :
prope r positioning of
jack
- Activa te the ve hicle ja cking mode before c ha ngin g a
w heel
=> p age 188.
- Posi tio n th e jack bel ow th e doo r sill und er t he mounting
point
th at is c los est to th e w hee l to be cha nged
=> p age 354 , fig. 28 7.
- Exten d the
jack und er the li ftin g po int on the do or sill
un til it s a rm is posi tio ned direct ly und er t he lif tin g p oint
=>& .
- Alig n the j ack so tha t its a rm @ en gag es t he plast ic
lif tin g p oint on the door sill a nd the mova ble base ® is
fl at on the
groun d=> fig . 288.
- Wind t he jack up furt her u ntil the flat t ire co mes off the
gr oun d=> &-
The jack must be installed only at the places indicated ~ page 354,
fig. 287 . There is exa ctly on e loca tion for e ach w heel. The ja ck m ust
not be positioned at any other
l ocation~ &.
The jack sho uld be posit ioned ap pro xima tely 8 in . (2 0 cm) be hind
th e fro nt whe el or 6 i n. (1 5 c m) in fr ont o f the rear w heel.
A n unstab le surfac e under th e jack can cause the vehicl e to s lip off
t h e jack . A lways pro vide a firm base for th e ja ck on the grou nd. If
necessary place a s turdy board or similar support under the ja ck. On ha
rd, s lippery surfaces (such as ti les) us e a rubb er mat or similar to
p revent th e ja ck fro m
slippin g~ & .
& WARNING
• You or your pa ssengers could be injured while changing a
wheel if you do not follow these safety precautions:
-Positioning the jack under the vehicle at any other place than
those indicated above may damage the vehicle or may result in
personal injuries.
- A soft or unstable surfa ce under the ja ck may cause the
vehicle to slip off the jack . Always provide a firm base for the
jack on the ground . If necessary , use a sturdy board under the
jack .
- On hard , slippery surface (such as tiles ) use a rubber mat or
similar to prevent the jack from slipping.
• To help prevent injury to yourself and your passengers :
- Do not raise the vehicle until you are sure the jack is securely
engaged .
- Passengers must not remain in the vehicle when it is jacked
up .
- Make sure that passengers wait in a safe place away from
the vehicle and well away from the road and traffic .
- Make sure jack position is correct , adjust as necessary and
then continue to raise the jack.
[ i ] Tips
Befo re c hangi ng th e wheel, yo u must ac tivate the jac king mode, s o
that the automatic controls for the Adapt ive Air Suspension do not
make it more difficult to lift the veh ic le with the
jack ~ page 188. •
Vehicle care Do-it-yourself service irechnical data