2008 AUDI A4 Telephone

Navigation107
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control If you would like to find a special destination without entering a
specific town, select Special destination
page 116 from the navi-
gation menu after selecting the country.
Selecting “Select destination on map”
You can also set your destination via the map display.
Once the map for the selection of a destination is displayed, cross-
hairs will appear in the centre of the corresponding town. You can
then specify a new destination by moving the crosshairs vertically
and horizontally
page 109.
Applies to vehicles: with navigation system
Single destination (route without stopover)
For a single destination the country and town must
always be specified. You can specify the destination
further by entering an address or a special destination.
Important: The system must be set to Route without
stopover
page 105.
– If the entry space
page 105, fig. 91 does not appear in
the MMI display, press the function selector button
marked .
– Turn the rotary pushbutton and select Country.– Press the rotary pushbutton. Using the rotary push-
button, you can now select a country from the list and
then copy it into the entry space by pressing the rotary
pushbutton.
– Turn the rotary pushbutton and select To w n / Z I P.
– Press the rotary pushbutton. The speller will appear on
the MMI display
page 43.
– Enter the town or the ZIP code via the speller.
– To complete the entry, turn the rotary pushbutton to
Centre (end entry) and press to confirm, or
– To enter additional data on the navigation destination,
turn the rotary pushbutton to Street, Special destination
in town or Select destination on map and press to
confirm.
– Enter the additional information.
– Start the route guidance by turning the rotary push-
button to Start route guidance and then pressing the
rotary pushbutton. The route criteria and subsequently
the map
page 110 will be shown on the MMI display.
An arrow will appear in the display of the driver informa-
tion system.
To add a house number or intersection after entering the destina-
tion, select the line
fig. 95 and complete your entries.
Note
•If your navigation destination contains special characters such
as the dashes in “Stratford-upon-Avon”, simply switch between the
speller for letters and the speller for numbers
page 43.
Fig. 95 Entering a
house number/inter-
section
NAV
A1










Navigation109
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
– Start the route guidance by turning the rotary push-
button to Start route guidance and then pressing the
rotary pushbutton. The route criteria and subsequently
the map
page 110 will be shown on the MMI display.
An arrow will appear in the display of the driver informa-
tion system.
Applies to vehicles: with navigation system
Setting a destination from the map
A point on the map can be set as a destination or stop-
over, stored in the directory and called up on the tele-
phone.
Important: The route guidance function must be activated

page 105.
Activating the map legend menu
– Press the Map control button. A map will appear on the
MMI display.
– Press the rotary pushbutton. The map legend menu will
now be activated, and the crosshairs will appear in the
map display
fig. 97.
Changing the map scale
– Turn the rotary pushbutton to position and press the
rotary pushbutton. You can now zoom out of or zoom in
on the map by turning the rotary pushbutton.
– Press the rotary pushbutton again to leave position .
Moving the crosshairs
– Turn the rotary pushbutton to position .
– Press the rotary pushbutton. Using the rotary push-
button, you can now move the crosshairs horizontally.
– Press the rotary pushbutton again. Using the rotary
pushbutton, you can now move the crosshairs vertically.
– To deactivate the moving crosshairs function, press the
rotary pushbutton again.
Setting a destination
– To set a selected point in the map as the destination, turn
the rotary pushbutton to position .
Fig. 97 Changing a
destination with the
crosshairs
Fig. 98 Calling a posi-
tion on the map
A1
A1
A3
A2










Navigation111
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control You can exit the legend menu by pressing .
Orientation. The map is displayed either facing north or facing
the direction of travel
page 118. If you select the orientation
option in the activated legend menu and press the rotary push-
button, the orientation switches from the direction of travel to
the direction facing north and vice versa. This setting is not
stored.
Scale. Turn the rotary pushbutton clockwise/anti-clockwise to
zoom in or out. You can also change the scale via the activated
legend menu. The setting that was last activated is stored.
Distance to the destination
Estimated time of arrival
Examples of selected map contents
Depiction of motorway exits on a scale of 50 m to 500 m. On a
scale of 750 m to 8 km the exits are displayed as dots.
Location of the vehicle
Destination control button. To switch to entry space

page 105, fig. 91 or the route plan
page 108, fig. 96.
If you use the crosshairs to select map contents, any existing
information on the contents (e.g. address, phone number) will
be displayed. If you select a traffic jam symbol and press the
rotary pushbutton, the corresponding TMC traffic report will be
displayed. On a scale of 1 km upwards, the map contents will
not be displayed.
Display of position coordinates of the crosshairs (longitude and
latitude).
Map position menu. The point on the map selected with the
crosshairs can be set as a destination or stopover, stored in the
directory and called up on the telephone
page 109.
The crosshairs can be moved horizontally and vertically by
turning and pressing the rotary pushbutton. Press the rotary
pushbutton to switch between the horizontal and vertical cross-
hair bars or deactivate this option. Using this option, you can,
for example, select a new destination
page 109.Moving along the route. This function can be used while route
guidance is activated. Turn the rotary pushbutton clock-
wise/anti-clockwise to move the map along the current route.
Altitude display
Note
Did you know that you can choose from four different map types

page 118?
Applies to vehicles: with navigation system
In the driver information system
RETURN
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
Fig. 101 Display when
a lane change is
required
Fig. 102 Display when
a turn-off is required










Navigation113
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
– Enter additional information.
– For quick access to a destination, place a tick next to
Display as top destination by turning and pressing the
rotary pushbutton. Top destinations are listed in the
destination entry screen
page 105, fig. 91 and can be
selected directly.
– Turn the rotary pushbutton to Store entry and press to
confirm.
Storing a destination in an existing entry
– Press the Memory control button.
– Turn the rotary pushbutton to Store in directory and
press to confirm.
– Turn the rotary pushbutton to Find entry and press to
confirm. The speller will appear on the MMI display

page 43.
– Enter the name of the entry you are searching for, or
– Turn the rotary pushbutton to LIST and press to confirm.
A list of all stored directory entries will appear.
– Turn the rotary pushbutton to the entry you wish to select
and press the rotary pushbutton.
– For quick access to a destination, place a tick next to
Display as top destination by turning and pressing the
rotary pushbutton. Top destinations are listed in the
destination entry screen
page 105, fig. 91 and can be
selected directly.
– Turn the rotary pushbutton to Store entry and press to
confirm.If a navigation destination is already stored in an existing address
card, the new destination will automatically overwrite the old one.
Note
•You can call up the address card to make further entries via the
function Edit directory.
•For information on how to manage the directory, please see

page 80.
Applies to vehicles: with navigation system
Route
Calculated routes with specific criteria can be stored and
loaded later as a new navigation destination
Important: You must have entered a route plan
page 108.
– Press the Memory control button.
– Turn the rotary pushbutton to Store route.
– Press the rotary pushbutton. The speller will appear on
the MMI display
page 43.
– Use the speller to enter a name for the route plan you
want to store.
–Turn the speller to OK and press the rotary pushbutton.
The route plan you entered will be stored.
If the function Store route appears in grey lettering, the route
memory is full. In this case, delete any obsolete routes from the
memory
page 117.





 




Navigation115
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
– Press the rotary pushbutton. The top category destina-
tion will be set as the final destination or as a stopover.
– Start the route guidance by turning the rotary push-
button to Start route guidance and then pressing the
rotary pushbutton. The route criteria and subsequently
the map
page 110 will be shown on the MMI display.
An arrow will appear in the display of the driver informa-
tion system.
Note
To update the list of top categories, exit the list by pressing the
button and select the same category again.
Applies to vehicles: with navigation system
Loading from the directory
Important: The navigation mode must be activated

page 105, and a navigation destination must be stored in
the directory
page 84.
– Press the Memory control button.
– Turn the rotary pushbutton to Load from directory.– Press the rotary pushbutton. A list of entries
fig. 105
will appear in the MMI display.
– To select a destination from the list turn the rotary push-
button to mark the entry and press to confirm, or
– To find an entry, turn the rotary pushbutton to Find entry
and press to confirm. You can now search for a name
using the speller.
– Start the route guidance by turning the rotary push-
button to Start route guidance and then pressing the
rotary pushbutton. The route criteria and subsequently
the map
page 110 will be shown on the MMI display.
An arrow will appear in the display of the driver informa-
tion system.
Applies to vehicles: with navigation system
Route
Routes that have been stored previously can be loaded as
a new navigation destination.
Important: The navigation mode must be activated

page 105, a route must have been stored
page 113,
and the system must be set to Route with stopover

page 105.
– Press the Memory control button.
– Turn the rotary pushbutton to Load route.
– Press the rotary pushbutton. A list of entries will appear
in the MMI display.
– To select a route from the list turn the rotary pushbutton
to mark a route and press to confirm.
RETURN
Fig. 105 Loading desti-
nation from directory










Navigation 116
– Start the route guidance by turning the rotary push-
button to Start route guidance and then pressing the
rotary pushbutton. The route criteria and subsequently
the map
page 110 will be shown on the MMI display.
An arrow will appear in the display of the driver informa-
tion system.
Other settings
Applies to vehicles: with navigation system
Special destinations
Special destinations can be selected in the entry space
when entering single destinations or stopovers.
– Select: Function selector button > Special
destination, or
– Select: Function selector button > stopover >
Special destination.
The navigation system can also guide you to special destinations
such as petrol stations or hotels. When entering your destination,
simply choose the approximate location of the special destination
(in the immediate vicinity, in the vicinity of the destination or nation-
wide). You can then select the category of the special destination
from a list (e.g. petrol station or hotel). The MMI display even indi-
cates the direction of the special destinations (arrows).
In immediate vicinity
The special destination is located in the immediate vicinity of your
vehicle. The special destinations are sorted according to the
distance from your current location, starting with the closest. You
can use this function, for example, to plan stopovers (closest restau-
rant).In vicinity of destination
The special destination is located in the vicinity of your destination.
You can use this function, for example, to find a petrol station near
your destination.
Nationwide
A special destination can be found irrespective of your current posi-
tion and your navigation destination. You can use this function, for
example, to navigate to an airport in the selected country.
Call: (telephone number)*
If telephone numbers are stored for a special destination on the
navigation DVD and your vehicle is equipped with a factory-fitted
telephone*, you can call the selected special destination. For
example, you can call a restaurant and reserve a table before driving
to the destination.
Note
There are certain destination entries in the list that cannot be
displayed completely because they are too long (too many charac-
ters). If you select one of these entries, a separate window will be
displayed after a few seconds. This window will show more informa-
tion about the selected entry.
Applies to vehicles: with navigation system
Top destination
– Select: Function selector button , or
– Select: Function selector button > stopover.
When storing a navigation destination, you can activate the func-
tion Display as top destination (). Top destinations are listed in the
destination entry screen
page 105, fig. 91 and can be copied into
the destination entry field directly.
NAV
NAV
NAV
NAV





!




Navigation117
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Applies to vehicles: with navigation system
Deleting a route
– Select: Function selector button > control button
Memory > Delete route.
Stored route plans (routes with stopovers) will now be deleted.
Applies to vehicles: with navigation system
Changing a route plan
A route plan (Route with stopover) can be changed, moved, deleted
or set as a destination again. Simply use the rotary pushbutton to
select the destination or a stopover on the route plan and then press
the rotary pushbutton. Then select one of the options displayed.
If you delete the destination, the last stopover will automatically be
set as the new destination.
Applies to vehicles: with navigation system
Route list
– Select: Function selector button > control button
Route > Route list.
The route list is only visible when the route guidance is active and
contains the following information:
•Details of the route
•Distances
•Street names
•Town and place names
Applies to vehicles: with navigation system
Route criteria
– Select: Function selector button > control button
Route > Route criteria.
The route will be calculated according to various criteria.
Dynamic navigation
The dynamic navigation function optimises a route plan by using
the most current traffic reports to automatically recalculate routes
and avoid traffic jams.
If the navigation does not display a detour route, although the
dynamic navigation function is ON and a traffic jam has been
reported on the planned route, this is because the estimated time
required for the detour is longer than the estimated time required
for remaining on the route with the traffic jam.
Route options
The navigation system selects the faster or shorter route.
Motorway / ferry / toll road
If you do not want the navigation system to include motorways,
ferries or toll roads in the route calculation, you can set the option
avoid. However, there can be situations in which you will not be able
to avoid them.
Note
If one of the selected criteria is unavoidable (i.e. the route must
contain the undesired criterion), the system will automatically
calculate the route accordingly.
NAV
NAV
NAV










Navigation 118
Applies to vehicles: with navigation system
Avoiding a route
– Select: Function selector button > control button
Route > Avoid route from here.
When the route guidance is activated, a section of the calculated
route that you have set will be avoided. The navigation system will
calculate an alternative route.
Using the rotary pushbutton, select the length of the route which is
to be avoided.
If you stop and restart the route guidance, it will be necessary to
reenter the route section to be avoided.
Note
If the MMI is not able to offer an alternative route, this indicates that
no suitable detour is available in the vicinity.
Applies to vehicles: with navigation system
Navigation details
– Select: Function selector button > control button
Nav-Info.
When the route guidance is activated, the following information on
your destination will be displayed:
•Destination / stopovers
•Estimated time of arrival
•Distance to the destination
•Current position of the vehicle
•Longitude and latitude coordinates of the destination
•Longitude, latitude and altitude of the vehicle
•Satellites received
The last route guidance cue will be repeated.
Call: (telephone number)*
If telephone numbers are stored for a special destination on the
navigation DVD and your vehicle is equipped with a factory-fitted
telephone*, you can call the selected special destination. For
example, you can call a restaurant and reserve a table before driving
to the destination.
Applies to vehicles: with navigation system
Map colours
– Select: Function selector button > function
selector button > Map colours.
Day
The map background will be lit brightly.
Night
The map background will be darkened.
Auto
When the dipped lights are on, the map scheme will switch from day
to night.
Applies to vehicles: with navigation system
Orientation
– Select: Function selector button > function
selector button > Orientation.
North
The map is set to face north. The position of the arrow will change
according to the movement and direction of the vehicle.
NAV
NAV
NAV
SETUP
NAV
SETUP