2008 Alfa Romeo 8C Release

137
5
A
USING THE VEHICLE
ELECTRIC PARKING
BRAKE
The vehicle is equipped with an automatic
parking brake EPB (Electric Parking Brake).
It is automatically engaged when the engine
is turned off and it is disengaged when, with
the engine running, the accelerator pedal is
depressed.
When the electric parking brake is engaged and
the key is turned to STOP, the warning light

illuminates on the instrument panel.During engagement and disengagement, the
warning light
flashes until the maximum
engagement force and full release have been
reached.
In the above conditions, the automatic activation
function can be deactivated/activated by
pressing the button A on the dashboard.
CAUTION
During engagement or
disengagement of the electric parking
brake, always hold the brake pedal
depressed.

139
5
A
USING THE VEHICLE
Malfunction indication
In the event of electric parking brake system
failures, the warning light
! on the display
will come on.
Depending on the message displayed, it signals
the following failures of the EPB system:
- Parking brake failure
If the message warning you to go to the
nearest Authorised Service Centre of the
Manufacturer’s Network is displayed,
drive slowly and remember that the electric
parking brake device is not functioning.
- Excessive temperature. If after leaving the engine off (key turned
to STOP) for about 15 minutes without
using the parking brake, the warning
light illuminates again when the engine
is started, slowly drive to an Authorised
Service Centre of the Manufacturer’s
Network. If the brake failure is accompanied by the
message “Mechanical release only”, the
manual emergency deactivation procedure
must be performed to release the parking
brake.
Deactivating the PARK OFF automatic
operation
To deactivate manual operation of the electric
parking brake, with the engine on, press the
button
A on the dashboard. The words PARK OFF
will appear on the display for 5 seconds and then
the page that was active previously will reappear.
To reactivate automatic operation, press the
button A again, the words PARK ON appear on
the display for 5 seconds.
WARNING: In certain conditions, when the
battery voltage is low, the electric parking brake
activation/deactivation system may temporarily
be deactivated for safety reasons. Therefore,
typically during engine starting when the battery
voltage drops, the message PARK OFF may
temporarily appear on the display indicating that
automatic operation is temporarily disabled.
WARNING: In the case of performance
starting, check that the electric parking brake is
disengaged.

140
5
D
- Parking brake system overhaul
The EPB system requires maintenance,
therefore contact an Authorised Service
Centre of the Manufacturer’s Network to
have the system corrected.
CAUTION
In the event of an electric
parking brake failure, contact an
Authorised Service Centre of the
Manufacturer’s Network as soon as
possible.
Emergency disengagement
In the event that the electric parking brake locks
with a total system failure, you need to manually
release the parking brake using the special tool
provided in the toolkit.
Proceed as follows:
- Move the left-hand seat fully forward and
fully tilt the backrest.
- Using a screwdriver remove the cover
D by
prising on its left-hand side.- Insert the special tool in the just uncovered
pipe.
- Turn the handle clockwise until it is
released.
- Remove the tool from the pipe and refi t the
cover.
CAUTION
After each manual emergency
release, the electric parking brake
system will be inefficient until its
operation is corrected by an Authorised
Service Centre of the Manufacturer’s
Network.

146
6
EMERGENCY
STARTINGIf the Alfa Romeo CODE fails to deactivate the
engine immobilizer, the CODE
warning light
will illuminate permanently, while the EOBD
warning light will go off after four seconds
to turn on again immediately afterwards: the
engine will not start. To start the engine, it is
necessary to follow the emergency starting
procedure.
WARNING: We recommend that you carefully
read the entire procedure before performing it.
If you make a mistake, turn the ignition key to
STOP and repeat the operations from step 1.1) Read the 5-digit electronic code found on
the CODE CARD.
2) Turn the ignition key to MAR: at this
moment the CODE
and EOBD
warning lights are on.
3) Depress the accelerator pedal and hold
it down. Approximately 8 seconds later,
the EOBD warning light will go off.
Release the accelerator and get ready to
count the number of times the EOBD warning light fl ashes.
4) As soon as the number of fl ashing is equal
to the fi rst digit of your CODE CARD, fully
depress the accelerator pedal and hold it
down until the EOBD warning light
goes off (after approximately 4 seconds).
You can now release the accelerator pedal.
5) The EOBD warning light starts fl ashing
again. As soon as the displayed number of
fl ashing is equal to the second digit of your
CODE CARD, depress the accelerator and
hold it down.
6) Follow the same procedure for the
remaining digits in the code on the CODE
CARD.
7) When the last digit has been entered, keep
the accelerator pedal pressed down. The
EOBD warning light comes on for 4
seconds and then goes off. You can now
release the accelerator pedal.
8) A quick fl ashing of the EOBD warning
light (about 4 seconds) confi rms that
procedure has been carried out correctly.
9) Start the engine by pressing the START
button while holding the brake pedal
depressed.If the EOBD warning light remains on,
turn the key to position STOP and repeat the
procedure from step 1.
This procedure can be repeated an unlimited
number of times.
WARNING: After an emergency staring, you
should contact an Authorised Service Centre of
the Manufacturer’s Network as the emergency
starting procedure will have to be carried out
every time you start the vehicle.

147
6
ABIN AN EMERGENCY
TOOLKIT
The vehicle is equipped with the following tools:
- toolkit, housed in the luggage compartment
- box with electric compressor, jack and
tools for fi tting the spare wheel (optional),
located inside the spare wheel itself.
The toolkit, housed under the floor panel,
contains:
- 8 + 10 open end wrench
- 13 + 17 open end wrench
- double slot + cross-head screwdriver
- tow hook
- Electric parking brake actuator release tool
IF A TYRE GETS A
PUNCTURE PRECAUTIONS IN THE
EVENT OF A PUNCTURE
If a tyre gets a puncture, you can make a first
emergency repair using the tyre repair kit
provided.
This kit allows repairing tyre punctures of up to
6 mm (7/32 in); the kit can be used in any
atmospheric condition.
Do not remove the foreign body (e.g. screw or
nail) from the punctured tyre.
Take the repair kit out of the bag found in the
luggage compartment and position it near the
punctured tyre.Screw the flexible inflation hose
A, onto the
pneumatic valve
B.

152
6
N
P
3) Replace the snap-fi tted bulb
P.
4) Refi t the bulb holder
N inserting fi rst the
electrical connector side and then pressing
on the other side to hook up the clip. THIRD STOP LIGHT
In order to replace the bulbs, you must remove
the light cluster. It is therefore advisable to
contact an Authorised Service Centre of the
Manufacturer’s Network. NUMBER PLATE LIGHTS
To replace the number plate light bulb (C 5W):
1) Release the dome light by gently prising on
the side with a screwdriver.
2) Remove the unit and turn the bulb holder.

168
6
B
C
A
IF THE BATTERY IS
FLAT First of all, we recommend that you read
the precautions contained in the section
”Maintenance“ to prevent the battery from
running flat and to help ensure its long life.
STARTING WITH THE
AUXILIARY BATTERY
See the chapter ”Starting the engine“ on page
114 in the section ”Using the vehicle”.WARNING: Under no circumstance should a
battery be used for an emergency start-up: This
could damage the electronic systems, particularly
the control units managing the ignition and fuel
supply functions.
RECHARGING THE
BATTERY
You are advised to recharge the battery slowly
and at a low amperage for about 24 hours.
Proceed as follows:
1) Deactivate the electronic alarm using the
radio control.
2) Lift the rear shelf
A and the box cover
B
and release the hooks
C.
WARNING: First disconnect the negative pole
terminal (–) then the positive pole one (+).3) Connect the battery charger cables to the
battery poles.WARNING: The battery is housed in a metal box, therefore, be extremely careful not to let the
battery charger clips come into contact with it.
4) Turn on the battery charger.
5) When the battery is recharged, turn off the
battery charger before disconnecting it from
the battery.
6) Reconnect the terminals to the battery
poles, observing the polarity.WARNING: First reconnect the positive pole
terminal (+) and then the negative pole one
(–).
WARNING: Before reconnecting the battery
terminals, check that the key has been removed
from the ignition or at least that it is in the STOP
position.

202
8
CAUTION
During the tyre life, the rolling
direction of the first fitting shall
always be observed, also in case of
“non-directional” tyres.
CAUTION
Check the depth of the tyre
tread at regular intervals (minimum
allowed value 1.6 mm). The thinner
is the tread, the greater is the risk of
skidding.
CAUTION
Drive carefully on wet roads to
decrease the risk of aquaplaning.
WINDSCREEN
WIPERSClean the rubber parts regularly using the
appropriate products.
Change the blades if the edge of the rubber
is deformed or worn. In any case, the blades
should be changed about once a year.
CAUTION
Travelling with worn wiper
blades is very dangerous because it
reduces the visibility in the event of
poor atmospheric conditions.
CAUTION
The arms of the wiper blade
have to be replaced with new ones
after having disassembled them twice.
The special arm fixing system ensures
optimal mechanical stability only after
the first two refitting operations,
provided that the specified tightening
torque is observed.CAUTION
We advise you to have any
operations involving removal of the
windscreen wiper arms performed at
an Authorised Service Centre of the
Manufacturer’s Network.
Some simple measures may reduce the
possibility of damage to the blades.
- In the case of temperatures below zero °C,
check that ice has not stuck the rubber part
against the windscreen glass. If necessary,
release with an anti-ice product.
- Remove any snow on the windscreen: as
well as protecting the blades, this avoids
forcing and overheating the electric motor.
- Do not activate the windscreen wipers when
the windscreen is dry.