2008 Acura TSX steering wheel

If maintenance service is done by
someone other than your dealer,
reset the maintenance minder as
f ollows:Turn the ignition switch to the ON
(II) position.
To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display. Press and hold the SEL/RESET
button on the steering wheel f or
more than 10 seconds. The
remaining engine oil lif e reset
modewillbeshownonthemulti-
inf ormation display.
To reset the engine oil lif e, press
the INFO button on the steering
wheel to select ‘‘RESET’’ on the
display, and press the SEL/
RESET button.
After the message on the multi-
inf ormation display is canceled by
pressing the INFO button, the
engine oil lif e display will appear in
the lower segment. You will see a
‘‘SERVICE’’ message along with the
percentage of the remaining engine
oil lif e and the maintenance item
code(s) displayed. Your dealer will reset the display
af ter completing the required
maintenance service. You will see
‘‘OIL LIFE 100 %’’ on the lower
segment of the multi-inf ormation
display and the maintenance item
code(s) erased the next time you
turn the ignition switch to the ON
(II) position.
If the engine oil lif e display is not
displayed, press the SEL/RESET
buttononthesteeringwheel
repeatedly until it comes back.
1.
2.
3.
CONT INUED
Maintenance Minder
Maint enance
283
‘‘SERVICE’’ MESSAGE
\f—\f—
y

y
(\fy\fy
2008 TSX

If you do not complete the reset
procedure within 30 seconds af ter
selecting the reset mode, the mode
will be canceled automatically.
If you have the required service
perf ormed but do not reset the
display, or reset the display without
perf orming the service, the system
will not show the proper
maintenance intervals. This can lead
to serious mechanical problems
because you will no longer have an
accurate record of when
maintenance is needed.To cancel resetting the oil life,
presstheINFObuttononthe
steering wheel to select
‘‘CANCEL’’ on the display, and
press the SEL/RESET button.
Immediately have the service
perf ormed, and make sure to reset
the display as previously described.
If the indicated maintenance service
is not done and the remaining engine
oil lif e reaches 0 %, the multi-
inf ormation display will show the
message ‘‘SERVICE PAST DUE’’
and the maintenance item code(s).
This message is displayed when the
total mileage is less than 10 miles
(f or U.S. models) or 10 km (f or
Canadian models) af ter the engine
oillifebecame0%. To cancel the message, press the
INFO button on the steering wheel.
Toseethemessageagain,waitfor
an interval for more than 5 seconds,
and then press the INFO button.
Maintenance Minder
284
\f—\f—
y

y
(\fy\fy
2008 TSX

After the message on the multi-
inf ormation display is canceled by
pressing the INFO button, the
engine oil lif e display will appear in
the lower segment. You will see a
‘‘SERVICE’’ message along with the
maintenance item code(s), and the
total negative mileage af ter the oil
lif e becomes 0 % is displayed.
Immediately have the service
perf ormed, and make sure to reset
the display as previously described.
This message is displayed when you
drive over 10 miles (f or U.S. models)
or 10 km (f or Canadian models)
after seeing the 0 % message.
Also, the total negative mileage
keeps blinking on the display.
This particular message is displayed
when you drive over 10 miles (f or
U.S. models) or 10 km (f or Canadian
models) af ter seeing the 0 %
message.
To cancel the message, press the
INFO button on the steering wheel.
To see the message again, wait f or
an interval of more than 5 seconds,
and then press the INFO button. To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display.
Maintenance Minder
286
U.S.
CANADA
\f—\f—
y


y
(\fy\f
y
2008 TSX

Check the level on the side of the
reservoir when the engine is cold.
The f luid should be between the
UPPER LEVEL and LOWER LEVEL.
If not, add power steering f luid to the
UPPER LEVEL.Pour the f luid slowly and caref ully
so you do not spill any. Clean up
any spill immediately; it could
damage components in the engine
compartment.
A low f luid level can indicate a leak
in the clutch system. Have this
system inspected as soon as possible.
The f luid level should be between
theMINandMAXmarksontheside
of the reservoir. If it is not, add
brake f luid to bring it up to that level.
Use the same fluid specified for the
brake system. Always use Honda Power Steering
Fluid. You may use another power
steering f luid as an emergency
replacement, but have the power
steering system f lushed and ref illed
with Honda PSF as soon as possible.
A low power steering f luid level can
indicate a leak in the system. Check
the f luid level f requently, and have
the system inspected as soon as
possible.
Manual Transmission only
Clutch Fluid
Power Steering Fluid
Brake and Clutch Fluid, Power Steering Fluid
Maint enance
301
MAX
MIN UPPER LEVEL
LOWER LEVEL
Turning the steering wheel to f ull lef t
or right lock and holding it there can
damage the power steering pump.
\f—\f—
y
y
(\fy\f\fy
2008 TSX

To change the bulb on the driver’s
side, start the engine, turn the
steering wheel all the way to the
right, then turn of f the engine. To
change the bulb on the passenger’s
side, turn the steering wheel to the
lef t.Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.
Pull the inner f ender cover away
f rom the f ender and bumper.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
4. 5.
2.
1.
3.
CONT INUED
Replacing a Front Side Marker/
FrontParkingLightBulb
Lights
Maint enance
305
HOLDING CLIPS BULBSOCKET
\f—\f—
y
\fy
(\fy\f
\fy
2008 TSX

CONT INUED
Replace your tires with radial tires of
the same size, load range, speed
rating, and maximum cold tire
pressure rating (as shown on the
tire’s sidewall).
Mixing radial and bias-ply tires on
your vehicle can reduce braking
ability, traction, and steering
accuracy. Using tires of a dif f erent
size or construction can cause the
ABS and vehicle stability assist
system (VSA) to work inconsistently.
To help increase tire lif e and
distribute wear more evenly, rotate
the tires according to the
maintenance messages displayed on
the multi-information display. Move
the tires to the positions shown in
the illustration each time they are
rotated. If you purchase directional
tires, rotate only front-to-back.
When the tires are rotated, make
sure the air pressures are checked.
In addition to proper inf lation,
correct wheel alignment helps to
decrease tire wear. If you f ind a tire
is worn unevenly, have your dealer
check the wheel alignment.
Have your dealer check the tires if
you f eel a consistent vibration while
driving. A tire should always be
rebalanced if it is removed f rom the
wheel. When you have new tires
installed, make sure they are
balanced. This increases riding
comf ort and tire lif e. For best results,
have the installer perform a dynamic
balance.
Tires
Replacing T ires and Wheels
Tire Rotation
T ire Maintenance
Maint enance
317
Front
(For non-directional
tires and wheels) (For directional
tires and wheels)
Improper wheel weights can damage
your vehicle’s aluminum wheels. Use
only genuine Acura wheels weights f or
balancing.
\f—\f—
y
y
(\fy\fy
2008 TSX

µµ
If your vehicle needs to be towed,
call a prof essional towing service or
organization. Never tow your vehicle
with just a rope or chain. It is very
dangerous.
The operator
loads your vehicle on the back of a
truck.
Therearetwowaystotowyour
vehicle: If , due to damage, your vehicle must
be towed with the f ront wheels on
the ground, do this:
Release the parking brake.
Shif t the transmission to neutral.
With the f ront wheels on the ground,
it is best to tow the vehicle no farther
than 50 miles (80 km), and keep the
speedbelow35mph(55km/h).
The tow
truck uses two pivoting arms that go
under the tires (f ront) and lif t them
of f the ground. The other two tires
remain on the ground. Turn of f the engine.
ShifttoD,thentoN.
Start the engine.
Release the parking brake.
Leave the ignition switch in the
ACCESSORY (I) position so the
steering wheel does not lock.
Leave the ignition switch in the
ACCESSORY (I) position so the
steering wheel does not lock.
Manual transmission:
Automatic transmission:
CONT INUED
Flat -bed EquipmentWheel-lif t Equipment
T his is the best way to
transport your vehicle.
T his is an
acceptable way to tow your
vehicle.
Emergency Towing
T aking Care of t he Unexpect ed
345
Improper towing preparation will
damage the transmission. Follow the
above procedure exactly. If you cannot
shif t the transmission or start the
engine (automatic transmission), your
vehicle must be transported with the
f ront wheels of f the ground.
\f—\f—
y

y
(\fy\f\fy
2008 TSX

Emergency Towing
346
Trying to lif t or tow your vehicle by the
bumpers will cause serious damage.
The bumpers are not designed to
support the vehicle’s weight.The steering system can be damaged if
the steering wheel is locked. Leave the
ignition switch in the ACCESSORY (I)
position, and make sure the steering
wheel turns f reely bef ore you begin
towing.
\f—\f—
y
\fy
(\fy\f
y
2008 TSX