2008 Acura RL Owner's Manual

ÛÝ
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. To exit ELAPSED TIME RESET
without changing the current setting,
select EXIT by pressing the INFO
( / ) button, then press the SEL/
RESET button. The screen goes
back to CUSTOMIZE MENU.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
elapsed time reset setup.
Multi-Inf ormation Display
102
\f—\f—
y\f
y
(\fy\f
\fy
2008 RL

ÛÝÛ
Ý
ÛÝ
ÛÝ
There are two position setups you
can make:MEMORY POSITION LINK
AUTO TILT & TELESCOPIC
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select POSITION SETUP by
pressing the INFO ( / ) button,
and then press the SEL/RESET
button.
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
CONT INUED
Position Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
103
Press the or button.
Press the SEL/RESET button. seepage104
seepage106
\f—\f—
y\fy
(\fy\f
\fy
2008 RL

ÛÝ
When Memory Position Link is set
to ON, the driver’s seat, the steering
wheel, and the outside mirror
positions move to the positions
stored in memory. To cause the
memory to activate, open the driver’s
door with the remote, or grab the
door handle while carrying the
remote.
To set the seat memory position, see
page . For inf ormation on using
the remote, see page . While the multi-information display
is in the POSITION SETUP screen
of the CUSTOMIZE GROUP, press
the SEL/RESET button. The screen
changes to the above display.Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
160
170
Memory Posit ion L ink
Multi-Inf ormation Display
104
\f—\f—
y\f\fy
(\fy\f
\fy
2008 RL

ÛÝ
To exit MEMORY POSITION LINK
without changing the current setting,
select EXIT by pressing the INFO
( / ) button, then press the SEL/
RESET button. The screen goes
back to CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
memory position link setup.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
105
\f—\f—
y\fy
(\fy\f

\fy
2008 RL

ÛÝÛÝ
When AUTO TILT & TELESCOPIC
is set to ON, the steering wheel
automatically moves f ully in and up
when you turn the ignition switch to
the LOCK (0) position and release it,
or when you remove the built-in key
from the ignition switch.
While the multi-information display
is in the POSITION SETUP screen
of the CUSTOMIZE GROUP, press
the SEL/RESET button. The screen
changes to CUSTOMIZE MENU.
Press the INFO ( / ) button until
you see the above display.Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
A ut o T ilt & T elescopic
Multi-Inf ormation Display
106
\f—\f—
y\fy
(\fy\f


y
2008 RL

ÛÝ
To exit AUTO TILT &
TELESCOPIC without changing the
current setting, select EXIT by
pressing the INFO ( / ) button,
then press the SEL/RESET button.
The screen goes back to
CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the auto
tilt and telescopic setup.
Multi-Inf ormation Display
Inst rument s and Cont rols
107
\f—\f—
y\fy
(\fy\f

y
2008 RL

Û
Ý
ÛÝ Û
Ý
ÛÝ
DOOR UNLOCK MODE
KEYLESS ACCESS
LIGHT FLASH
KEYLESS ACCESS BEEP
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button, until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
There are three settings in the
keyless access setup:
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select KEYLESS ACCESS
SETUP by pressing the INFO ( / ) button, then press the SEL/
RESET button.
K EYL ESS A CCESS Setup
Multi-Inf ormation Display
108
Press the or button.
Press the SEL/RESET button. seepage109
seepage111
seepage113
\f—\f—
y\f\fy
(\fy\f

y
2008 RL

ÛÝ
To select whether the driver’s door
or all doors unlock when you open
the driver’s door with the remote or
by grabbing the door handle (while
carrying the remote), f ollow these
instructions:
While the multi-information display
is in the KEYLESS ACCESS SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to the above display.Press the SEL/RESET button. The
screen changes as shown above.
Select DRIVER DOOR ONLY or
ALL DOORS by pressing the INFO
( / ) button, then press the SEL/
RESET button to enter your
selection.
CONT INUED
Door Unlock Mode
Multi-Inf ormation Display
Inst rument s and Cont rols
109
\f—\f—
y\f

y
(\fy\f

y
2008 RL