2008 Acura MDX ignition

This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position.
If itcomesonandstaysonatany
other time, or it does not come on
when you turn the ignition switch to
the ON (II) position, there is a
problem with the VSA system. You
will also see a ‘‘CHECK VSA
SYSTEM’’ message on the multi-
inf ormation display (see page ).
Take your vehicle to a dealer to have
it checked. Without VSA, your
vehicle still has normal driving ability,
but will not have VSA traction and
stability enhancement. For more
inf ormation, see page .
This indicator may also come on if
there is a problem with the trailer
stability assist f unction (see page). This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position. For more inf ormation, see
page .
This indicator has f our f unctions.
Itcomesonasareminderthatyou
have turned off the vehicle
stability assist (VSA) system.
It flashes when VSA is active (see
page ).
It f lashes when trailer stability
assist is activating (see page ).
It comes on along with the VSA
system indicator if there is a
problem with the VSA system.
You will also see a ‘‘CHECK VSA
SYSTEM’’ message and a
‘‘CHECK TRAILER STABILITY
ASSIST’’ message on the multi- inf ormation display (see page ).
The lef t or right turn signal indicator
blinks when you signal a lane change
or turn. If an indicator does not blink
or blinks rapidly, it usually means
one of the turn signal bulbs is
burned out (see page ). Replace
the bulb as soon as possible, since
other drivers cannot see that you are
signaling.
When you press the hazard warning
button, both turn signal indicators
and all turn signals on the outside of
the vehicle f lash.
1.
2.
3.
4.
81 81
359
375 359
359 375 404
Instrument Panel Indicators
Vehicle Stability Assist
(VSA ) System Indicator
VSA A ctivation Indicator
Turn Signal and
Hazard Warning
Indicators
Inst rument s and Cont rols
67
——yy
()-
yy
2008 MDX

This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position.
This indicator has two f unctions:This indicator monitors the
temperature of the automatic
transmission f luid. It should come on
f or a f ew seconds when you turn the
ignition switch to the ON (II)
position. If it comes on while driving,
it means the transmission fluid
temperature is too high. Pull to the
side of the road when it is saf e, shif t
to Park, and let the engine idle until
the indicator goes out.
You will also see an ‘‘A/T TEMP
HIGH’’ message on the multi-
inf ormation display (see page ).
If this happens, pull to the side of
the road when it is saf e, check
which tire has lost pressure on the
multi-inf ormation display, and
determine the cause. If it is
because of a flat tire, have the flat
tire repaired as soon as possible. If
two or more tires are
underinf lated, call a prof essional
towing service. For more
inf ormation, see page .
If this indicator begins to f lash,
there is a problem with the tire
pressure monitoring system
(TPMS). You will also see a
‘‘CHECK TPMS SYSTEM’’
message on the multi-inf ormation
display. The indicator continues to
f lash f or a while (approximately 1
minute), then stays on. If this
happens, have your dealer check
the system as soon as possible.
For more inf ormation, see page
.
Check the tire pressure monitor on
the multi-inf ormation display and
determinethecause(seepage).
You will also see a ‘‘CHECK TIRE
PRESSURE’’ message on the multi-
inf ormation display (see page ). If it comes on while driving, it
indicates that one or more of your
vehicle’s tires are signif icantly low
on pressure.
1.
82
2.
82 446
352 354
Instrument Panel Indicators
Low Tire Pressure/
TPMS Indicator A/T Temperature
Indicator
68
Continuing to drive with the A/T
temperature indicator on may cause
serious damage to the transmission.
\f—\f—\fy\f\fy
()-
\fy\f\fy
2008 MDX

If the indicator blinks while driving,
it indicates the dif f erential
temperature is too high.
TEMP. HIGH’’ message on the
multi-inf ormation display (see page).
Pull to the side of the road when it is
saf e, shif t to Park, and let the engine
idle until the indicator goes out.
This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position. If this indicator comes on at
any other time, there is a problem in
display (see page ). Take your
For more inf ormation, see page .
This indicator comes on when there
is a system message on the multi-
inf ormation display. Press the INFO
button on the steering wheel (see
page ) to see the message (see
page ).
Most of the time, this indicator
comes on along with other indicators
in the instrument panel such as the
seat belt reminder indicator, SRS
indicator, VSA system indicator, etc.
81
73
8282
348
Instrument Panel Indicators
Super Handling-All
Indicator
Message Indicator
Inst rument s and Cont rols
69

damage to the system.
——yy
()-
yy
vehicletoadealertohaveitchecked.
indicatorblinkingmaycauseserious
messageonthemulti-information
WheelDrive(SH-AWD®)
®theSH-AWD system. You will also
seea‘‘CHECKSH-AWD®SYSTEM’’
Youwillalsoseea‘‘SH-AWD®DIFF
ContinuingtodrivewiththeSH-AWD®
2008 MDX

This indicator comes on when you
turn on the cruise control system by
pressing the CRUISE button (see
page ).
This indicator comes on when you
set the cruise control. See pagef or inf ormation on operating the
cruise control. This indicator comes on with the
high beam headlights. For more
inf ormation, see page .
This indicator comes on when you
turn on the f og lights. For more
inf ormation, see page . This indicator reminds you that the
exterior lights are on. It comes on
when the light switch is in either the or position. This indicator
will also come on when the light
switch is in AUTO and the lights
turn on automatically. If you turn the
ignition switch to the ACCESSORY
(I) or the LOCK (0) position without
turning of f the light switch, this
indicator will remain on. A reminder
chime will also sound when you open
the driver’s door.
This indicator comes on brief ly when
you turn the ignition switch to the
ON (II) position. It will then go of f if
you have inserted a properly-coded
ignition key. If it is not a properly-
coded key, the indicator will blink,
and the engine’s f uel system will be
disabled (see page).
128
120118
270
270
Instrument Panel Indicators
Cruise Control Indicator Cruise Main Indicator High Beam Indicator
Fog L ight Indicator Lights On Indicator
Immobilizer System
Indicator
70
——yy
()-
yy
2008 MDX

This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position. If this indicator comes on at
any other time, there is a problem in
the system. While this indicator is on,
the comfort button will not work, and
the system will remain in the sport
mode. You will also see a ‘‘CHECK
ADS SYSTEM’’ message on the
multi-inf ormation display. Have the
vehicle checked by your dealer as
soon as possible. For more
inf ormation, see page .This indicator comes on as a
reminder that you must ref uel soon.
When the indicator comes on, there
is about 1.8 US gal (7.0
)of fuel
remaining in the tank bef ore the
needle reaches E. There is a small
reserve of f uel remaining in the tank
when the needle reaches E. You will
also see a ‘‘LOW FUEL’’ message on
the multi-information display (see
page ). This indicator comes on when the
security system is set. See page
f or more inf ormation on the
security system.
82
361
269
Active Damper System
Indicator
L ow Fuel Indicator Security System Indicator
Instrument Panel Indicators
Inst rument s and Cont rols
71
LOW FUEL INDICATOR
SECURITY SYSTEM INDICATOR
\f—\f—\fy\f
\f
y
()-
\fy\f\fy
2008 MDX

ÛÝÛÝ
ÛÝThe multi-inf ormation display in the
instrument panel displays various
inf ormation and messages when the
ignition switch is in the ON (II)
position. Some of the messages help
you operate your vehicle more
comf ortably.
Others help to keep you aware of the
periodic maintenance your vehicle
needs f or continued trouble-f ree
driving.
When you open the driver’s door, a
‘‘Welcome’’ message is shown on the
multi-inf ormation display. When you
turn the ignition switch from the ON
(II) position to the ACCESSORY (I)
position, a ‘‘Goodbye’’ message is
shownonthedisplay.
To change the display, press the
INFO( / )buttononthesteering
wheel repeatedly until the main
menu appears (see page ).With the ignition switch in the ON
(II) position, the multi-inf ormation
display changes as shown in the next
page each time you press the INFO
( / ) button or SEL/RESET
button.
When you turn the ignition switch to
the ON (II) position, what you last
selected is displayed.
In the multi-information display, the
system message is also displayed
(see page ) and you can
customize your vehicle control
settings (see page ).
74 83
80
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
73
INFO ( / )
BUTTON
SEL/
RESET
BUTTON
\f—\f—\fy\f

y
()-
\fy\f\fy
2008 MDX

This shows the estimated distance
you can travel on the fuel remaining
in the f uel tank. This distance is
estimated f rom the f uel economy
you received over the last several
miles(U.S.) or kilometers (Canada),
so it will vary with changes in speed,
traf f ic, etc.
This shows your vehicle’s average
f uel economy in mpg (U.S. models)
or liter/100 km (Canadian models)
since you last reset the Trip A or
Trip B.
You can customize the Trip A and
AVERAGE FUEL A reset condition
in the multi-information display (see
page ).
This shows the average speed you
are traveling in miles per hour (mph)
forU.S.modelsorkilometersper
hour (km/h) f or Canadian models.
To reset the AVERAGE SPEED you
have traveled, press and hold the
SEL/RESET button until the
number resets.This shows the time passed traveled
since you last reset it. When you turn
the ignition switch to the ON (II)
position, ELAPSED TIME is reset.
If you want to reset the ELAPSED
TIME manually, go to the trip
computer’s ELAPSED TIME display,
andpressandholdtheSEL/RESET
button until the number resets.
You can customize the ELAPSED
TIME reset condition on the multi-
inf ormation display (see page ).
92
94
AVERAGE FUEL A/B RANGE
A VERA GE SPEEDEL A PSED T IME
Multi-Inf ormation Display
Inst rument s and Cont rols
79
\f—\f—\fy\f\fy
()-
\fy\f\fy
2008 MDX

When the main menu displays
‘‘Keyless Memory Settings ,’’ you
can customize some vehicle control
settings.
To enter the customizing mode,
press the SEL/RESET button.If you turn the ignition switch to the
ACCESSORY (I) or the LOCK (0)
position, or move the shif t lever out
of Park, the display will change to
the normal screen.
You can customize some vehicle
control settings f or ‘‘DRIVER 1’’ and
‘‘DRIVER 2’’ separately. If ‘‘DRIVER
1’’ or ‘‘DRIVER 2’’ is not displayed,
customizing is not possible.
To have the driver’s ID detected,
make sure your remote transmitter
is linked to the system (see Keyless
Memory Settings on page).
If you want the settings as they were
when the vehicle lef t the f actory,
select DEFAULT ALL, as described
on page .
Ref er to the table on the f ollowing
pages about the settings you want to
customize.
If you want to change any vehicle
control settings, select CHG
SETTING, then press the SEL/
RESET button.
To change the settings, the ignition
switch must be in the ON (II)
position, and the vehicle must be
stopped with the transmission in
Park. 86
139
CONT INUED
Multi-Inf ormation Display
Customize Settings
Inst rument s and Cont rols
83
TM TM
\f—\f—\fy\fy
()-
\fy\f\fy
2008 MDX