2008.5 Citroen C5 ECU
[x] Cancel search: ECUPage 117 of 306
121
8
S A F E T Y
For the airbags to be fully
effective, observe the following
safety rules:
Sit in a normal upright position.
Wear a correctly adjusted seat belt.
Do not leave anything between the
occupants and the airbags (a child,
pet, object...). This could hamper the
operation of the airbags or injure the
occupants.
After an accident or if the vehicle
has been stolen or broken into, have
the airbag systems checked.
All work on the airbag system is
strictly forbidden unless it is carried
o u t b y q u a l i fi e d p e r s o n n e l o f t h e
CITROËN network.
Even if all of the precautions men-
tioned are observed, a risk of injury
or of minor burns to the head, chest
or arms when an airbag is triggered
c a n n o t b e r u l e d o u t . T h e b a g i n fl a t e s
almost instantly (within a few millisec-
o n d s ) t h e n d e fl a t e s w i t h i n t h e s a m e
time discharging the hot gas via
openings provided for this purpose. Front airbags
Do not drive holding the steering
wheel by its spokes or resting your
hands on the centre part of the
wheel.
Passengers must not place their feet
on the dashboard.
If possible, do not smoke as deploy-
ment of the airbags can cause burns
or the risk of injury from a cigarette
or pipe.
Never remove or pierce the steering
wheel or hit it violently.
Side airbags
Use only approved covers on the
s e a t s . T h e s e w i l l n o t h i n d e r i n fl a -
tion of the side airbags. Consult a
CITROËN dealer.
D o n o t fi x o r a p p l y a n y t h i n g t o t h e
seat backs. This could cause injury
to the chest or arms if the side air
bag is triggered.
Do not sit with the upper part of the
body any nearer to the door than
necessary. Curtain airbags
D o n o t fi x o r a p p l y a n y t h i n g t o t h e
roof. This could cause injury to the
head if the curtain airbag is trig-
gered.
Do not remove the grab handles in-
stalled on the roof, they play a part
in securing the curtain airbags.
Page 119 of 306
121
8
S A F E T Y
For the airbags to be fully
effective, observe the following
safety rules:
Sit in a normal upright position.
Wear a correctly adjusted seat belt.
Do not leave anything between the
occupants and the airbags (a child,
pet, object...). This could hamper the
operation of the airbags or injure the
occupants.
After an accident or if the vehicle
has been stolen or broken into, have
the airbag systems checked.
All work on the airbag system is
strictly forbidden unless it is carried
o u t b y q u a l i fi e d p e r s o n n e l o f t h e
CITROËN network.
Even if all of the precautions men-
tioned are observed, a risk of injury
or of minor burns to the head, chest
or arms when an airbag is triggered
c a n n o t b e r u l e d o u t . T h e b a g i n fl a t e s
almost instantly (within a few millisec-
o n d s ) t h e n d e fl a t e s w i t h i n t h e s a m e
time discharging the hot gas via
openings provided for this purpose. Front airbags
Do not drive holding the steering
wheel by its spokes or resting your
hands on the centre part of the
wheel.
Passengers must not place their feet
on the dashboard.
If possible, do not smoke as deploy-
ment of the airbags can cause burns
or the risk of injury from a cigarette
or pipe.
Never remove or pierce the steering
wheel or hit it violently.
Side airbags
Use only approved covers on the
s e a t s . T h e s e w i l l n o t h i n d e r i n fl a -
tion of the side airbags. Consult a
CITROËN dealer.
D o n o t fi x o r a p p l y a n y t h i n g t o t h e
seat backs. This could cause injury
to the chest or arms if the side air
bag is triggered.
Do not sit with the upper part of the
body any nearer to the door than
necessary. Curtain airbags
D o n o t fi x o r a p p l y a n y t h i n g t o t h e
roof. This could cause injury to the
head if the curtain airbag is trig-
gered.
Do not remove the grab handles in-
stalled on the roof, they play a part
in securing the curtain airbags.
Page 150 of 306
150
10
C H E C K S
BONNET
Protects the components of the
engine and provides access for
checking levels.
Opening
Lift the lever B and raise the bonnet.
Unclip the strut C from its housing
and pivot it to insert it in the notch
D indicated by a yellow arrow.
F i x t h e s t r u t i n t h e n o t c h t o h o l d
the bonnet open. Closing
Take the strut out of the support
notch.
Clip the strut in its housing.
Lower the bonnet then slam it
fi r m l y a t t h e e n d o f i t s t r a v e l .
Pull on the bonnet to check that
it is secured correctly.
To avoid any risk of burns, only han-
dle the bonnet strut by its yellow
end.
The location of the interior control
prevents opening of the bonnet
while the front passenger’s door is
closed.
This operation must only be carried
out when the vehicle is stationary.
Avoid opening the bonnet in strong
winds.
Open the front passenger door.
Pull the interior control A , located
at the bottom of the door frame.
Page 165 of 306
165
11
P R A C T I C A L I N F O R M A T I O N
Access to the spare wheel
To remove the spare wheel
L i f t u p t h e b o o t fl o o r u s i n g t h e
strap (Saloon) or the retractable
handle (Tourer).
Fold back the boot carpet
(Saloon).
Attach the hook to the top of the
boot.
Detach the strap then push the
wheel forwards so as to be able
to lift it. To reposition the spare wheel
P o s i t i o n t h e s p a r e w h e e l fl a t i n
the boot, then pull it towards
you.
N e x t p l a c e t h e t o o l b o x i n s i d e t h e
wheel, then secure the assembly
with the belt.
Release the strap to return the
b o o t fl o o r t o i t s i n i t i a l p o s i t i o n . The tyre pressure is indi-
cated on the label located
on the left-hand door centre
pillar. On this label, the pressures
a r e s p e c i fi e d , a c c o r d i n g t o t h e v e -
hicle load.
Page 167 of 306
167
11
P R A C T I C A L I N F O R M A T I O N
Wheel for temporary use
Y o u r v e h i c l e m a y b e fi t t e d w i t h a
spare wheel which is different to
t h o s e o n t h e v e h i c l e . W h e n fi t t i n g
the spare wheel, it is normal to no-
tice that the wheel bolt washers do
not come into contact with the wheel
rim. The spare wheel is secured by
the conical tapering of the wheel
bolt’s shaft.
W h e n r e fi t t i n g t h e o r i g i n a l w h e e l ,
ensure that the wheel bolt contact
surfaces are clean and in good con-
dition. Fitting a wheel
Fit the wheel on the hub, using
the centring guide. Make sure
that the contact surface between
the hub and the wheel is clean.
Screw in the bolts but do not fully
tighten them.
Lower the jack and remove it.
Tighten the wheel bolts, using
the wheelbrace.
R e fi t t h e p r o t e c t o r s o n t h e b o l t s .
Return the ground clearance to
the normal position.
Ensure the tyre pressure is cor-
rect and have the balancing
checked.
Deflation detection
These wheels have tyre pressure
sensors. It is essential to have re-
pairs carried out by a CITROËN
dealer.
Anti-theft bolts
Each wheel is equipped with one
anti-theft bolt.
To remove it:
Remove the protector using tool 3 .
Use the anti-theft socket with the
wheelbrace. I f y o u r v e h i c l e i s fi t t e d w i t h
a spare wheel of a different
size to those on the vehi-
c l e , y o u m u s t n o t e x c e e d 5 0 m p h
(80 km/h) whilst using the spare
wheel.
T h e w h e e l b o l t s a r e s p e c i fi c t o t h e
type of wheel.
If the type of wheel is changed,
check with your CITROËN dealer
that the wheel bolts are compatible
with the new wheels.
Take care to note down the code
number engraved on the head of
the anti-theft bolt socket. This will
enable you to obtain a replace-
ment anti-theft bolt socket from a
CITROËN dealer .
Page 168 of 306
167
11
P R A C T I C A L I N F O R M A T I O N
Wheel for temporary use
Y o u r v e h i c l e m a y b e fi t t e d w i t h a
spare wheel which is different to
t h o s e o n t h e v e h i c l e . W h e n fi t t i n g
the spare wheel, it is normal to no-
tice that the wheel bolt washers do
not come into contact with the wheel
rim. The spare wheel is secured by
the conical tapering of the wheel
bolt’s shaft.
W h e n r e fi t t i n g t h e o r i g i n a l w h e e l ,
ensure that the wheel bolt contact
surfaces are clean and in good con-
dition. Fitting a wheel
Fit the wheel on the hub, using
the centring guide. Make sure
that the contact surface between
the hub and the wheel is clean.
Screw in the bolts but do not fully
tighten them.
Lower the jack and remove it.
Tighten the wheel bolts, using
the wheelbrace.
R e fi t t h e p r o t e c t o r s o n t h e b o l t s .
Return the ground clearance to
the normal position.
Ensure the tyre pressure is cor-
rect and have the balancing
checked.
Deflation detection
These wheels have tyre pressure
sensors. It is essential to have re-
pairs carried out by a CITROËN
dealer.
Anti-theft bolts
Each wheel is equipped with one
anti-theft bolt.
To remove it:
Remove the protector using tool 3 .
Use the anti-theft socket with the
wheelbrace. I f y o u r v e h i c l e i s fi t t e d w i t h
a spare wheel of a different
size to those on the vehi-
c l e , y o u m u s t n o t e x c e e d 5 0 m p h
(80 km/h) whilst using the spare
wheel.
T h e w h e e l b o l t s a r e s p e c i fi c t o t h e
type of wheel.
If the type of wheel is changed,
check with your CITROËN dealer
that the wheel bolts are compatible
with the new wheels.
Take care to note down the code
number engraved on the head of
the anti-theft bolt socket. This will
enable you to obtain a replace-
ment anti-theft bolt socket from a
CITROËN dealer .
Page 183 of 306
180
11
P R A C T I C A L I N F O R M A T I O N
FUSEBOX C
Fuse N° Rating
Function
F1 15 A Rear screen wipe (Tourer)
F2 30 A Locking and deadlocking relay
F3 5 A Airbags
F4 10 A A u t o m a t i c g e a r b o x - a d d i t i o n a l h e a t e r u n i t ( D i e s e l ) - e l e c t r o c h r o m e r e a r v i e w m i r r o r s
F5 30 A Front window - sun roof - passenger door lighting - passeng er rear view mirror adjustment
F6 30 A Rear window
F7 5 A V a n i t y m i r r o r l i g h t i n g - G l o v e b o x l i g h t i n g - i n t e r i o r l a m p s - t o r c h ( t o u r e r )
F8 20 A R a d i o - C D c h a n g e r - C o n t r o l s a t t h e s t e e r i n g w h e e l - D i s p l a
y - D e fl a t i o n d e t e c t i o n - E l e c t r i c
boot ECU
F9 30 A Cigar-lighter - front 12 V socket
F10 15 A Alarm - Controls on the steering wheel, signalling and scre en wipe controls
F11 15 A Low current ignition switch
F12 15 A Driver’s electric seat - instrument panel - seat belt not fasten
ed warning lamps -air
conditioning controls
F13 5 A Engine relay unit - Hydraulic suspension pump cut-off relay - a irbag ECU supply
F14 15 A Rain and brightness sensor - parking assistance - passenger’s electri
c seat - trailer relay
u n i t - H I F I a m p l i fi e r E C U - H a n d s - f r e e k i t - L a n e D e p a r t u r e W a r n i n g S y s t e m
F15 30 A Locking and deadlocking relay
F17 40 A H e a t e d r e a r s c r e e n - e x t e r i o r h e a t e d r e a r v i e w m i r r o r s
FSH SHUNT PARK SHUNT
Page 186 of 306
183
11
P R A C T I C A L I N F O R M A T I O N
BATTERY
Procedure for charging your battery
w h e n i t i s fl a t o r f o r s t a r t i n g t h e e n -
gine using another battery. Starting using another
battery
Access to the battery V6 HDi engine
The battery is located under the
bonnet.
To gain access to it:
open the bonnet using the inte-
r i o r l e v e r , t h e n t h e e x t e r i o r l e v e r ,
secure the bonnet strut,
remove the plastic cover to gain
access to the two terminals,
u n c l i p t h e f u s e b o x t o r e m o v e
the battery, if necessary. The battery is located in the boot un-
der the left-hand wing trim.
To gain access to it:
open the boot,
o p e n t h e fl a p a n d r e m o v e t h e
battery.
Lift the pins to remove the front
left headlamp cover (V6 HDi en-
gine).
Connect the red cable to the
p o s i t i v e t e r m i n a l ( + ) o f t h e fl a t
battery A , then to the positive ter-
minal (+) of the slave battery B .
Connect one end of the green or
black cable to the negative ter-
minal (-) of the slave battery B .
V6 HDi engine: the positive ter-minal (-) is located under the red cover.
Connect the other end of the
green or black cable to the earth
point C on the broken down ve-
hicle.
Operate the starter, let the en-
gine run.
Wait until the engine returns to
idle and disconnect the cables.