2008.5 Citroen C4 Owner's Manual

123
IX
D R I V I N G
In bad weather or in winter, ensure
that the sensors are not covered
with mud, ice or snow. When re-
verse gear is engaged, an audible
signal (long beep) indicates that
the sensors may be dirty.
Reactivation

 Press button A again, the warn-
ing lamp switches off, the system
is reactivated.
Deactivation Operating fault
If an operating fault occurs, this warn-
ing lamp is displayed on the instrument
panel and/or a message appears on
the multifunction screen, accompa-
nied by an audible signal (short beep),
when reverse gear is engaged.
Consult a CITROËN dealer.

 Press button A , the warning lamp
comes on, the system is fully de-
activated.
The system will be deactivated au-
tomatically when a trailer is being
towed or when a bicycle carrier is
fi tted (vehicle fi tted with a towbar
or bicycle carrier recommended by
CITROËN).

125
X
C H E C K S
BONNET
Protects the components of the en-
gine and provides access for check-
ing levels.
Opening
 Push the exterior control B to the
left and raise the bonnet.


Unclip the strut C from its housing.

 Fix the strut in the notch to hold
the bonnet open. Closing

 Take the strut out of the support
notch.

 Clip the strut in its housing.

 Lower the bonnet then slam it
fi rmly at the end of its travel.

 Pull on the bonnet to check that
it is secured correctly.
The location of the interior control
prevents opening of the bonnet
while the driver’s door is closed.
This operation must only be carried
out when the vehicle is stationary.
Avoid opening the bonnet in strong
winds.

 Pull to the right the interior
control A , located under the
dashboard.

126
X
C H E C K S
BLEEDING THE DIESEL FILTER
Protective cover
Removal

 Remove the protective cover by
unclipping fi rst point 1 , then 3
and 4 .

 Unclip point 2 pulling towards
you, then lift.
Refi tting

 Clip point 2 fi rst.

 Lower the cover, centring it.

 Clip points 1 and 4 , pushing ver-
tically and slightly rearwards.

 Clip point 3 , pushing vertically. Draining water from the fuel
filter
Bleed on a regular basis (at every
oil change).
To evacuate the water, slacken the
bleed screw or the water-in-diesel-
fuel sensor, which is located at the
base of the fi lter.
Persist until water ceases to fl ow
out.
Then retighten the bleed screw or
the water-in-diesel-fuel sensor.

127
C H E C K S
RUNNING OUT OF FUEL (DIESEL)
HDi 135 and 140 engine
Detach the protection cover to gain
access to the priming pump. HDi 90 and 110 engine
Detach the protection cover to gain
access to the priming pump. Priming the fuel circuit
In the event of running out of fuel:

 after fi lling (minimum 5 litres),
action the manual priming pump,
until some resistance is felt,

 then operate the starter, gently
pressing the accelerator until the
engine starts.
If the engine fails to start at the fi rst
attempt, wait 15 seconds before try-
ing again.
If the engine fails to start after a few
attempts, repeat the procedure from
the beginning. When the engine is
idling, accelerate gently to complete
the purge of the circuit.
HDi engines are of a highly
technical nature.
All maintenance and re-
pairs require specifi c qualifi cations
which only your CITROËN dealer
can guarantee.

128
X
C H E C K S
PETROL ENGINES
The caps and covers allow access for checking the levels of the various fl uids and for replacing certain components.

1. Power steering reservoir.

2. Screenwash and headlamp wash
reservoir.
3. Coolant reservoir.

4. Brake fl uid reservoir.

5. Battery.
6. Fuse box.

7. Air fi lter * .

8. Dipstick.

9. Engine oil fi ller cap.
* According to engine.

129
X
C H E C K S * According to engine.
DIESEL ENGINES
The covers and caps allow access for checking the levels of the vari ous fl uids, for replacing certain components and for
priming the fuel system.

1. Power steering reservoir.

2. Screenwash and headlamp
wash reservoir.

3. Coolant reservoir.

4. Brake fl uid reservoir.

5. Battery.
6. Fuse box.

7. Air fi lter * .

8. Dipstick.

9. Engine oil fi ller cap.

10. Priming pump * .

11. Degas screw * . As the diesel fuel circuit is
pressurised, any work on
this circuit is prohibited.

130
X
C H E C K S
CHECKING LEVELS
Check all of these levels regularly
and top them up if necessary, unless
otherwise indicated.
If a level drops signifi cantly, have the
corresponding system checked by a
CITROËN dealer.
Oil level
Draining the engine
Refer to the Maintenance and
Warranty Guide for details of the in-
terval for this operation. Oil specifi cation
The oil must correspond to your en-
gine and conform to the manufactur-
er’s recommendations.
Brake fluid level
Draining the circuit
Refer to the Maintenance and
Warranty Guide for details of the in-
terval for this operation.
This fl uid must be changed regu-
larly. Fluid which has been used for
too long may cause a loss of braking
effi ciency.
Fluid specifi cation
The brake fl uid must conform to the
manufacturer’s recommendations
and fulfi l the DOT4 standards.
Coolant level
Draining the circuit
The coolant does not have to be
changed.
Fluid specifi cation
The coolant must conform to the
manufacturer’s recommendations.
The reading will only be
correct if the vehicle is on
level ground and the engine
has been off for more than
15 minutes.
The check is carried out either when
the ignition is switched on using the
oil level indicator on the instrument
panel, or using the dipstick.
Between two oil changes, the con-
sumption should not exceed 0.5 litre
per 600 miles (approx. 1 000 km).
Check this level also between each
scheduled service and before long
journeys. The brake fl uid level should
be close to the "MAX" mark.
If it is not, check the brake
pad wear.
The coolant level should be
close to the "MAX" mark but
should never exceed it.
When the engine is warm,
the temperature of the coolant is
regulated by the fan. This can oper-
ate with the ignition off.

On vehicles which are fi tted with
a particle emission fi lter, the fan
may operate after the vehicle has
been switched off, even if the en-
gine is cold.
In addition, as the cooling system is
pressurised, wait at least one hour
after switching off the engine before
carrying out any work.
To avoid any risk of scalding, un-
screw the cap by two turns to al-
low the pressure to drop. When the
pressure has dropped, remove the
cap and top up the level.
In order to maintain the re-
liability of the engine and
emission control system,
the use of additives in the engine
oil is prohibited.

131
X
C H E C K S
Screenwash and headlamp
wash fluid
Fluid specifi cation
For optimum cleaning and to avoid
freezing, this fl uid must not be topped
up or replaced with plain water.
Reservoir capacities:
-
screenwash: approximately 3 litres,
- screenwash and headlamp wash: approximately 6 litres. Diesel additive level (Diesel
engine with particle emission
filter)
A low additive level is indicated by
lighting of the service warning lamp,
accompanied by an audible warning
and a message on the multifunction
screen.
Topping up
This additive must be topped up by
a CITROËN dealer without delay.
Used products
Avoid prolonged contact of
used oil or fl uids with the
skin.
Most of these fl uids are harmful to
health or indeed very corrosive.
Do not discard used oil or
fl uids into sewers or onto
the ground.
Take used oil to an authorised
waste disposal site.
In the case of vehicles fi tted
with headlamp washers, the
minimum level of this fl uid is
indicated by an audible sig-
nal and a message on the multifunc-
tion screen.
Top up the level when you next stop
the vehicle.