2008.5 Citroen C3 PICASSO DAG ABS
[x] Cancel search: ABSPage 18 of 207
!
!
21
INSTRUMENTS and CONTROLS
When the engine is running or the vehi-
cle is moving, the lighting of one of the
following warning lights indicates the
occurrence of a fault requiring interven-
tion on the part of the driver.
Central alert.
Lighting is associated with
the displaying of another
warning light:
- braking,
- power steering,
- engine oil pressure,
- coolant temperature,
stop the vehicle immediately and as
safely as possible. Service.
If this comes on, it indicates
the occurrence of a problem
in one of the systems which
d o e s n o t h a v e a s p e c i fi c
warning light.
In order to identify it, consult the mes-
sage on the multifunction display.
Check:
- the engine oil level,
- t h e s c r e e n w a s h fl u i d l e v e l ,
- the remote control battery,
- the condition of the bulbs.
For any other situations, contact a
CITROËN dealer.
The illumination of this warning light
may also indicate that the (Diesel) par-
t i c l e fi l t e r i s s t a r t i n g t o g e t c l o g g e d u p ,
d u e t o s p e c i fi c e x t e n d e d u r b a n d r i v i n g
conditions: low speed, congestion, etc.
I n o r d e r t o r e g e n e r a t e t h e fi l t e r , y o u a r e
a d v i s e d t o d r i v e , o n c e t r a f fi c c o n d i t i o n s
allow, at a speed of 40 mph (60 km/h)
or above for at least 5 minutes (until the
warning light goes out). Braking.
If this comes on, it indicates the
occurrence of a fault in one of
the braking systems:
- s i g n i fi c a n t d r o p i n t h e l e v e l i n t h e circuit,
- electronic brake force distribution (EBFD) faulty (simultaneous lighting
of the ABS warning light),
stop the vehicle immediately and as
safely as possible.
When the vehicle is moving, check that
the handbrake is fully released.
Any fault resulting in the displaying
of a warning light must be the sub-
ject of further diagnostics by read-
ing the associated message on the
multifunction display.
Should you encounter any prob-
lems, do not hesitate to contact a
CITROËN dealer.
Warning lights
Anti-lock braking system
(ABS).
If this comes on, it indicates the
occurrence of a fault in the anti-
lock braking system.
However, this does not prevent opera-
tion of the vehicle's assisted braking.
Dynamic stability control
(ESP/ASR).
The ESP/ASR system is put
into service automatically when
the vehicle is started.
Unless the system has been deactivated,
if this warning light and the indicator light
on the button come on continuously, this
indicates the occurrence of a fault in the
ESP/ASR system.
If the warning light remains on,
contact your CITROËN dealer.
Page 96 of 207
!
85
Installing a booster seat
The chest part of the seat belt must
be positioned on the child's shoulder
without touching the neck.
Ensure that the lap part of the seat
belt passes correctly over the child's
thighs.
C I T R O Ë N r e c o m m e n d s t h e u s e o f
a b o o s t e r s e a t w h i c h h a s a b a c k , fi t -
ted with a seat belt guide at shoulder
level. As a safety precaution, do not leave:
- one or more children alone and
unsupervised in a vehicle,
- a child or an animal in a vehicle which is exposed to the sun, with
the windows closed,
- the keys within reach of children inside the vehicle.
To prevent accidental opening of the
doors and rear windows, use the
" C h i l d l o c k " .
Take care not to open the rear win-
dows by more than one third.
To protect young children from the
r a y s o f t h e s u n , fi t s i d e b l i n d s o n t h e
rear windows.
The incorrect installation of a child
seat in a vehicle compromises the
child's protection in the event of an ac-
cident.
R e m e m b e r t o f a s t e n t h e s e a t b e l t s o r
the child seat harnesses keeping the
slack in relation to the child's body to a
minimum , even for short journeys.
For optimum installation of the
"forwards-facing" child seat, ensure
that the back of the child seat is in
contact with the back of the vehicle's
seat and that the head restraint does
not cause any discomfort.
I f t h e h e a d r e s t r a i n t h a s t o b e r e m o v e d ,
ensure that it is stored or attached se-
curely to prevent it from being thrown
around the vehicle in the event of sharp
braking.
C h i l d r e n u n d e r t h e a g e o f 1 0 m u s t n o t
travel in the "forwards-facing" position
on the front passenger seat, unless
the rear seats are already occupied by
other children, cannot be used or are
absent.
D i s a r m t h e p a s s e n g e r a i r b a g w h e n
a "rearwards-facing" child seat is in-
stalled on the front seat.
Otherwise, the child would risk being
seriously injured or killed if the air bag
w e r e t o i n fl a t e .
Page 103 of 207
!
i
!
91
BRAKING ASSISTANCE SYSTEMS
Group of supplementary systems which
help you to obtain optimum braking in
complete safety in emergency situations:
- the anti-lock braking system (ABS),
- the electronic brake force distribu-tion (EBFD),
- the emergency braking assistance (EBA).
Anti-lock braking system and electronic brake force distribution
Linked systems which improve the sta-
bility and manoeuvrability of your vehi-
cle when braking, in particular on poor
or slippery surfaces.
When braking in an emergency,
p r e s s v e r y fi r m l y w i t h o u t r e l e a s i n g
the pressure. When replacing wheels (tyres and
rims), ensure that they conform to
the manufacturer’s recommenda-
tions.
Operating fault
If this warning light comes on,
accompanied by an audible
signal and a message on the
multi-function display, it indicates
a malfunction of the anti-lock braking sys-
tem which could result in loss of control of
the vehicle when braking.
If this warning light comes on,
together with the STOP and
ABS warning lights, accompa-
nied by an audible signal and a
message on the multifunction display, it
indicates a malfunction of the electronic
brake force distribution which could
result in loss of control of the vehicle
when braking.
You must stop as soon as it is safe
to do so.
Emergency braking assistance
System which, in an emergency, ena-
bles you to obtain the optimum braking
pressure more quickly, thus reducing
the stopping distance.
Activation
The anti-lock braking system comes
into operation automatically when there
is a risk of wheel lock.
Normal operation of the ABS may make
itself felt by slight vibration of the brake
pedal. Activation
It is triggered by the speed at which the
brake pedal is pressed.
The effect of this is a reduction in the
resistance of the pedal and an increase
i n b r a k i n g e f fi c i e n c y .
In both cases, contact a CITROËN
dealer. When braking in an emergency,
p r e s s fi r m l y w i t h o u t r e l e a s i n g t h e
pressure.
Page 136 of 207
123
PRACTICAL INFORMATION
Changing fog/reversing light bulbs
open the boot,
press on the tabs using 2 screwdrivers,
disconnect the light connector,
t u r n t h e b u l b h o l d e r b y a q u a r t e r
turn,
r e m o v e t h e b u l b a n d r e p l a c e i t .
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n r e -
v e r s e o r d e r . Changing the third stop light bulbs
(4 x W 5 W bulbs)
open the boot,
remove the two plugs located on the
boot inner panel,
press on the body of the light with
2 screwdrivers to remove it from its
housing,
turn the corresponding bulb-holder
a q u a r t e r t u r n ,
p u l l t h e b u l b a n d r e p l a c e i t .
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n r e -
v e r s e o r d e r . Changing the number plate light
bulbs (W 5 W)
insert a thin screwdriver into one of
the lens' exterior holes,
p u s h i t o u t w a r d s t o u n c l i p .
r e m o v e t h e l e n s .
p u l l t h e b u l b a n d r e p l a c e i t .
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n r e -
v e r s e o r d e r .
Page 141 of 207
128
PRACTICAL INFORMATION
Engine compartment fuses
The fuse box is placed in the engine
compartment near the battery (left-hand
s i d e ) .
Access to the fuses
U n c l i p t h e c o v e r .
Change the fuse (see correspond-
i n g p a r a g r a p h ) .
W h e n y o u h a v e fi n i s h e d , c l o s e t h e
cover carefully to guarantee the
s e a l i n g o f t h e f u s e b o x . Fuse table
Fuse N° Rating Functions
F1 20 A Engine control unit supply, cooling fan unit control,
m u l t i f u n c t i o n e n g i n e c o n t r o l m a i n r e l a y .
F2 15 A H o r n .
F3 10 A F r o n t / r e a r w a s h - w i p e .
F4 20 A D a y t i m e r u n n i n g l a m p s .
F5 15 A D i e s e l h e a t e r ( d i e s e l e n g i n e ) , f u e l p u m p ( p e t r o l
engine)
F6 10 A ABS/ESP control unit, ABS/ESP cut-off relay,
s e c o n d a r y s t o p s w i t c h .
F7 10 A E l e c t r i c a l p o w e r s t e e r i n g .
F8 25 A S t a r t e r c o n t r o l .
F9 10 A S w i t c h i n g a n d p r o t e c t i o n u n i t ( D i e s e l ) .
F10 30 A D i e s e l e n g i n e i n j e c t i o n p u m p v a l v e , i n j e c t o r s a n d
ignition coils (petrol engine)
F11 40 A A i r c o n d i t i o n i n g b l o w e r .
Page 142 of 207
129
PRACTICAL INFORMATION
Fuse N° Rating Functions
F12 30 A W i n d s c r e e n w i p e r s s l o w / f a s t s p e e d .
F13 40 A B u i l t - i n s y s t e m s i n t e r f a c e s u p p l y ( i g n i t i o n p o s i t i v e ) .
F14 30 A V a l v e t r o n i c s u p p l y ( p e t r o l ) .
F15 10 A R i g h t - h a n d m a i n b e a m h e a d l a m p .
F16 10 A L e f t - h a n d m a i n b e a m h e a d l a m p .
F17 15 A L e f t - h a n d d i p p e d h e a d l a m p .
F18 15 A R i g h t - h a n d d i p p e d h e a d l a m p .
F19 15 A Multifunction engine control supply (petrol engine),
a i r c o o l i n g s o l e n o i d v a l v e s ( D i e s e l ) .
F20 10 A Multifunction engine control supply (petrol engine),
T u r b o p r e s s u r e r e g u l a t i o n v a l v e ( D i e s e l ) , e n g i n e
c o o l a n t l e v e l d e t e c t o r ( D i e s e l ) .
F21 5 A Fan assembly control supply, APC, ABS ESP
r e l a y s .
Page 148 of 207
i!
134
PRACTICAL INFORMATION
TOWING THE VEHICLE
Access to the tools Towing your vehicle
On the front bumper, unclip the cover
b y p r e s s i n g a t t h e b o t t o m .
S c r e w t h e t o w i n g e y e i n f u l l y .
I n s t a l l t h e t o w b a r .
Switch on the hazard warning lights
o n t h e t o w e d v e h i c l e .
P l a c e t h e g e a r l e v e r i n n e u t r a l .
On the rear bumper, unclip the cover
b y p r e s s i n g a t t h e b o t t o m .
S c r e w t h e t o w i n g e y e i n f u l l y .
I n s t a l l t h e t o w b a r .
Switch on the hazard warning lights
o n t h e t o w e d v e h i c l e .
Towing another vehicle
The towing eye is installed under the
b o o t fl o o r .
To gain access to it:
open the boot,
r e m o v e t h e m o v a b l e b o o t fl o o r ,
lift up the boot carpet,
remove the towing eye from the tool
h o l d e r . When towing with all four wheels on
t h e g r o u n d , a l w a y s u s e a t o w b a r .
When towing with only two wheels
on the ground, always use profes-
s i o n a l l i f t i n g e q u i p m e n t .
When towing with the engine off,
there is no longer any braking or
s t e e r i n g a s s i s t a n c e .
Failure to observe this special con-
dition could result in damage to
certain braking components and
the absence of braking assistance
t h e n e x t t i m e t h e e n g i n e i s s t a r t e d .
Procedure for having your vehicle towed
or for towing another vehicle using a re-
m o v a b l e t o w i n g e y e .