Page 132 of 207
i
!
i
!
i
119
PRACTICAL INFORMATION
CHANGING A BULB
Procedure for replacing a faulty bulb
with a new bulb
Front lights
1.
Direction indicators (H21 W amber).
2. Dipped headlamps (H7-55 W).
3. Main beam headlamps (H1-55 W).
4. Side lights (W 5 W).
5. Fog lamps (PSX24 W).
In certain climatic conditions (low
temperature, humidity), the pres-
ence of condensation on the in-
side of the headlamp and light
glass is normal ; it disappears
a few minutes after the lights are
s w i t c h e d o n .
Handle the bulbs using a dry
c l o t h .
T h e h e a d l a m p s a r e fi t t e d w i t h p o l y -
carbonate lenses, coated with a
protective varnish:
do not clean them with a dry
or abrasive cloth or using a
detergent or solvent product,
use a sponge and soapy water,
when using a high pressure
washer on stubborn dirt, do not
spend too long on the head-
lamps, lights and their sur-
rounds to avoid damaging their
v a r n i s h a n d t h e i r s e a l s .
Changing direction indicator bulbs Amber coloured bulbs, such as
the direction indicators, must be
replaced with bulbs of identical
s p e c i fi c a t i o n s a n d c o l o u r .
R e m o v e t h e p l a s t i c p r o t e c t i v e c o v e r .
Pull the bulb-holder and replace the
b u l b .
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n r e -
v e r s e o r d e r .
W h e n r e fi t t i n g , c l o s e t h e p l a s t i c
cover carefully to guarantee the
s e a l i n g o f t h e h e a d l a m p . If either of the direction indicator
w a r n i n g l i g h t s i s fl a s h i n g q u i c k l y ,
o n e o f t h e b u l b s i s f a u l t y .
Page 135 of 207
PRACTICAL INFORMATION
Rear lights
1. Brake/side lights (12VP21/5 W).
2. Fog lamp, left-hand side (PR21 W)
Reversing light, right-hand side
(P21 W).
3. Direction indicators (P21 W) Changing brake/side lights and
direction indicator bulbs
u n s c r e w t h e t w o l i g h t fi x i n g b o l t s ,
extract the light carefully pulling it by
its shaft,
t u r n t h e b u l b h o l d e r a q u a r t e r t u r n ,
remove the faulty bulb and replace
i t .
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n r e -
v e r s e o r d e r .
Page 136 of 207
123
PRACTICAL INFORMATION
Changing fog/reversing light bulbs
open the boot,
press on the tabs using 2 screwdrivers,
disconnect the light connector,
t u r n t h e b u l b h o l d e r b y a q u a r t e r
turn,
r e m o v e t h e b u l b a n d r e p l a c e i t .
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n r e -
v e r s e o r d e r . Changing the third stop light bulbs
(4 x W 5 W bulbs)
open the boot,
remove the two plugs located on the
boot inner panel,
press on the body of the light with
2 screwdrivers to remove it from its
housing,
turn the corresponding bulb-holder
a q u a r t e r t u r n ,
p u l l t h e b u l b a n d r e p l a c e i t .
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n r e -
v e r s e o r d e r . Changing the number plate light
bulbs (W 5 W)
insert a thin screwdriver into one of
the lens' exterior holes,
p u s h i t o u t w a r d s t o u n c l i p .
r e m o v e t h e l e n s .
p u l l t h e b u l b a n d r e p l a c e i t .
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n r e -
v e r s e o r d e r .
