PERIODIC MAINTENANCE AND MINOR REPAIR
EAUB1410
Replacing the license plate
light bulb
1. Reinforcement plate
2. Bulb socket
3. License plate light bulb
1. Remove the reinforcement plate
by removing the bolts and nuts.
2. Remove the license plate light
bulb socket by pulling it out.
NOTE:
When removing the license plate light
bulb socket, be careful not to pull too
hard.
EAU24350
Supporting the motorcycle
Since this model is not equipped with
a centerstand, follow these precau-
tions when removing the front and rear
wheel or performing other mainte-
nance requiring the motorcycle to
stand upright. Check that the motorcy-
cle is in a stable and level position be-
fore starting any maintenance. A
strong wooden box can be placed un-
der the engine for added stability.
To service the front wheel
1. Stabilize the rear of the motorcy-
cle by using a motorcycle stand
or, if an additional motorcycle
stand is not available, by placing
a jack under the frame in front of
the rear wheel.
2. Raise the front wheel off the
ground by using a motorcycle
stand.
6-36
1
2
3
4
5
6
7
8
9
10
3. Remove the defective bulb by
pulling it out of the socket.
4. Insert a new bulb into the socket.
5. Install the bulb socket by pushing
it in.
6. Install the reinforcement plate in
the original position, and then
tighten bolts and nuts to the spec-
ified torque.
Tightening torque:
Reinforcement plate nut:
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Reinforcement plate bolt (centre):
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Reinforcement plate bolt (upper):
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
MY03 04-06 ING 6-10-2005 9:26 Pagina 6-36
PERIODIC MAINTENANCE AND MINOR REPAIR
6-38
1
2
3
4
5
6
7
8
9
10
EAU25080
Rear wheelEAU25311
To remove the rear wheelEWA10820
WARNING0
It is advisable to have a Yama-
ha dealer service the wheel.
Securely support the motorcy-
cle so that there is no danger of
it falling over.
1. Wheel axle nut
2. Drive chain slack adjusting bolt
3. Locknut
4. Drive chain
1. Wheel axle
2. Brake caliper bracket
1. Loosen the axle nut.
2. Lift the rear wheel off the ground
according to the procedure on
page 6-36.
3. Remove the axle nut.
4. Loosen the locknut on each side
of the swingarm.
5. Turn the drive chain slack adjust-
ing bolts fully in direction (a) and
push the wheel forward.
6. Remove the drive chain from the
rear sprocket.
4. Install the brake calipers by in-
stalling the bolts.
NOTE:
Make sure that there is enough space
between the brake pads before in-
stalling the brake calipers onto the
brake discs.
5. Install the brake hose holders by
installing the bolts.
6. Tighten the wheel axle, the front
wheel axle pinch bolt and the
brake caliper bolts to the speci-
fied torques.
Tightening torques:
Wheel axle:
72 Nm (7.2 m·kgf, 52 ft·lbf)
Front wheel axle pinch bolt:
14 Nm (1.4 m·kgf, 10 ft·lbf)
Brake caliper bolt:
40 Nm (4.0 m·kgf, 29 ft·lbf)
7. Push down hard on the handlebar
several times to check for proper
fork operation.
MY03 04-06 ING 6-10-2005 9:26 Pagina 6-38
1
2
3
4
5
6
7
8
9
10
PERIODIC MAINTENANCE AND MINOR REPAIR
6-39
NOTE:
If the drive chain is difficult to re-
move, remove the wheel axle first,
and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.
The drive chain cannot be disas-
sembled.
7. While supporting the brake
caliper bracket, pull the wheel
axle out, and then remove the
wheel.
ECA11070CAUTION:
Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.
EAU34430
To install the rear wheel
1. Install the wheel and the brake
caliper bracket by inserting the
wheel axle from the right-hand
side.
NOTE:
Make sure that the retainer on the
swingarm is inserted into the slot
in the brake caliper bracket.
Make sure that there is enough
space between the brake pads
before installing the wheel.
2. Install the drive chain onto the
rear sprocket.
3. Install the axle nut, and then low-
er the rear wheel so that it is on
the ground.
4. Adjust the drive chain slack. (See
page 6-23.)
5. Tighten the axle nut to the speci-
fied torque.
Tightening torque:
Axle nut:
150 Nm (15.0 m·kgf, 108 ft·lbf)
EAU25870
Troubleshooting
Although Yamaha motorcycles receive
a thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition systems,
for example, can cause poor starting
and loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your motorcycle
require any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the motorcycle
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
MY03 04-06 ING 6-10-2005 9:26 Pagina 6-39
