2007 YAMAHA MT-03 low beam

INSTRUMENT AND CONTROL FUNCTIONS
3-4
1
2
3
4
5
6
7
8
9
10
When the key is turned to “OFF” and
30 seconds have passed, the indicator
light will start flashing indicating the
immobilizer system is enabled. After
24 hours have passed, the indicator
light will stop flashing, however the im-
mobilizer system is still enabled.
This model is also equipped with a
self-diagnosis device for the immobi-
lizer system. (See page 3-7 for an ex-
planation of the self-diagnosis device.)
EAU11060
Neutral indicator light “N”
This indicator light comes on when the
transmission is in the neutral position.
EAU11020
Turn signal indicator light “y”
This indicator light flashes when the
turn signal switch is pushed to the left
or right.
EAU11080
High beam indicator light “1”
This indicator light comes on when the
high beam of the headlight is switched
on.
EWA10060
WARNING0
Never turn the key to “OFF” or
“LOCK” while the vehicle is moving,
otherwise the electrical systems
will be switched off, which may re-
sult in loss of control or an acci-
dent. Make sure that the vehicle is
stopped before turning the key to
“OFF” or “LOCK”.
EAU11530
Engine trouble warning light “U”
This warning light comes on or flashes
when an electrical circuit monitoring
the engine is defective. When this oc-
curs, have a Yamaha dealer check the
self-diagnosis system. (See page 3-7
for an explanation of the self-diagno-
sis device.)
The electrical circuit of the warning
light can be checked by turning the
key to “ON”. If the warning light does
not come on for a few seconds, then
go off, have a Yamaha dealer check
the electrical circuit.
EAU11440
Coolant temperature warning
light “u”
This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and allow
the engine to cool.
The electrical circuit of the warning
light can be checked by turning the
key to “ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical
circuit.
ECA10020
CAUTION:
Do not operate the engine if it is
overheated.
EAU11361
Fuel level warning light “K”
This warning light comes on when the
fuel level drops below approximately
4.25 L (1.12 US gal) (0.93 Imp.gal).
When this occurs, refuel as soon as
possible.
MY03 01-03 ING 6-10-2005 13:52 Pagina 3-4

1
2
3
4
5
6
7
8
9
10
INSTRUMENT AND CONTROL FUNCTIONS
3-9
EAU12343
Handlebar switches
Left
1. Pass switch “1”
2. Dimmer switch “2/ 1”
3. Horn switch “o”
4. Turn signal switch “y”
5. Hazard switch “
r”
Right
1. Engine stop switch “I/B”
2. Start switch “J”
EAU12350
Pass switch “1”
Press this switch to flash the head-
light.
EAU12400
Dimmer switch “2/1”
Set this switch to “
1” for the high
beam and to “2” for the low beam.
EAU12500
Horn switch “o”
Press this switch to sound the horn.
EAU12460
Turn signal switch “y”
To signal a right-hand turn, push this
switch to “∆”. To signal a left-hand
turn, push this switch to “Ÿ”. When re-
leased, the switch returns to the cen-
ter position. To cancel the turn signal
lights, push the switch in after it has
returned to the center position.
EAU12660
Engine stop switch “I/B”
Set this switch to “I” before starting the
engine. Set this switch to “
B” to stop
the engine in case of an emergency,
such as when the motorcycle overturns
or when the throttle cable is stuck.
EAU12710
Start switch “J”
Push this switch to crank the engine
with the starter.
ECA10050CAUTION:
See page 5-1 for starting instruc-
tions prior to starting the engine.
,
MY03 01-03 ING 6-10-2005 13:52 Pagina 3-9

1
2
3
4
5
6
7
8
9
10
OPERATION AND IMPORTANT RIDING POINTS
EAU15950
EWA10270
WARNING0
Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer re-
garding any control or function
that you do not thoroughly un-
derstand.
Never start the engine or oper-
ate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of con-
sciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.
Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised com-
pletely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.
EAUB1340
Starting the engine
In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
The transmission is in the neutral
position.
The transmission is in gear with
the clutch lever pulled and the
sidestand up.
EWA10290
WARNING0
Before starting the engine,
check the function of the igni-
tion circuit cut-off system ac-
cording to the procedure de-
scribed on page 3-20.
Never ride with the sidestand
down.
1. Turn the key to “ON” and make
sure that the engine stop switch is
set to “
I”.
ECAB0040CAUTION:
The following warning lights and in-
dicator lights should come on for a
few seconds, then go off.
Neutral indicator light
Turn signal indicator light
High beam indicator light
Engine trouble warning light
Coolant temperature warning
light
Fuel level warning light
Immobilizer system indicator
light
If a warning or indicator light does
not go off, see page 3-3 for the cor-
responding warning and indicator
light circuit check.
2. Shift the transmission into the
neutral position.
5-1
MY03 04-06 ING 6-10-2005 9:24 Pagina 5-1

PERIODIC MAINTENANCE AND MINOR REPAIR
Headlight lens
•Do not affix any type of tinted
film or stickers to the head-
light lens.
•Do not use a headlight bulb
of a wattage higher than
specified.
5. Install the headlight bulb cover,
and then connect the coupler.
6. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAUB1380
Replacing an auxiliary
light bulb
1. Auxiliary light socket
2. Auxiliary light bulb
If the auxiliary light bulb burns out, re-
place it as follows.
1. Turn the handlebar to the right or
left side to access the auxiliary
light socket.
2. Remove the auxiliary light socket
(together with the bulb) by pulling it.
3. Remove the defective bulb by
pulling it out.
4. Insert a new bulb into the socket.
5. Install the auxiliary light socket
(together with the bulb) by push-
ing it in.
EAUB1370
Replacing the tail/brake
light bulb
1. Tail/brake light bulb cover
2. Cover bolts
1. Tail/brake light socket
2. Tail/brake light bulb
6-34
1
2
3
4
5
6
7
8
9
10
MY03 04-06 ING 6-10-2005 9:25 Pagina 6-34

1
2
3
4
5
6
7
8
9
10
INDEX
A
Air filter element, cleaning the
check hoses ..................................6-13
Air filter element, replacing ..............6-13
Anti-theft alarm (optional)...................3-8
Auxiliary light bulb, replacing ...........6-34
B
Battery ..............................................6-29
To access the battery....................6-29
To charge the battery ....................6-30
To store the battery .......................6-31
Brake and clutch levers,
checking and lubricating ...............6-26
Brake fluid ........................................6-22
Changing ......................................6-22
Checking fluid level.......................6-21
Brake lever .......................................3-11
Brake pads, checking.......................6-20
Brake pedal ......................................3-11
Lubricating ....................................6-26
C
Cables, checking and lubricating .....6-25
Care and storage ...............................7-1
Cast wheels......................................6-19
Catalytic converter ...........................3-13
Checking and lubricating the
brake and clutch levers.................6-26
Checking and lubricating the
brake pedal ...................................6-26Checking and lubricating the
cables ...........................................6-25
Checking and lubricating the
sidestand ......................................6-27
Checking and lubricating the
throttle grip and cable ...................6-25
Checking the sidestand switch.........3-20
Clock mode ........................................3-7
Clutch lever ......................................3-10
Clutch lever free play, adjusting .......6-19
Consumer information ........................9-1
Controls and instruments ...................2-3
Function ..........................................3-1
Coolant .............................................6-12
Coolant temperature warning light .....3-4
D
Description .........................................2-1
Controls and instrument .................2-3
Left view..........................................2-1
Right view .......................................2-2
Dimmer switch....................................3-9
Drive chain, cleaning and
lubricating .....................................6-24
Drive chain slack ..............................6-23
Adjusting .......................................6-23
Checking .......................................6-23
E
Engine break-in ..................................5-3
Engine idling speed, adjusting .........6-14
Engine oil and oil filter element ..........6-8Engine oil filter element....................6-10
Engine stop switch .............................3-9
Engine trouble warning light...............3-4
F
Front fork, checking .........................6-27
Front wheel ......................................6-37
Installing........................................6-37
Removing......................................6-37
Fuel ..................................................3-12
Fuel consumption, tips for reducing ...5-3
Fuel level warning light ......................3-4
Fuel tank breather/overflow hose.....3-13
Fuel tank cap ....................................3-11
Fuses, replacing ...............................6-31
H
Handlebar switches ............................3-9
Dimmer switch ................................3-9
Engine stop switch..........................3-9
Hazard switch ...............................3-10
Horn switch .....................................3-9
Pass switch .....................................3-9
Start switch .....................................3-9
Turn signal switch ...........................3-9
Headlight bulb, replacing .................6-33
High beam indicator light ...................3-4
Horn switch ........................................3-9
I
Identification numbers ........................9-1
Idling speed, adjusting .....................6-14
Ignition circuit cut-off system............3-19
MY03 07-10 ING 5-10-2005 17:09 Pagina 1