2007 YAMAHA MT-03 drain bolt

DESCRIPTION
EAU10410
Left view
1. Main fuse (page 6-31)
2. Battery (page 6-29)
3. Idle adjusting screw (page 6-14)
4. Air filter element (page 6-13)
5. Owner’s tool kit (page 6-1)6. Seat lock (page 3-14)
7. Shift pedal (page 3-10)
8. Engine oil drain bolt (crankcase) (page 6-9)
9. Engine oil drain bolt (oil tank) (page 6-9)
2-1
1
2
3
4
5
6
7
8
9
10
MY03 01-03 ING 6-10-2005 13:54 Pagina 12

1
2
3
4
5
6
7
8
9
10
DESCRIPTION
EAU10420
Right view
2-2
10. Grab bar
11. Fuse box (page 6-32)
12. Rear brake fluid reservoir (page 6-21)
13. Front brake fluid reservoir (page 6-21)
14. Coolant reservoir (page 6-12)15. Engine oil filler cap/dipstick (page 6-8)
16. Coolant drain bolt (page 6-12)
17. Engine oil filter element (page 6-10)
18. Shock absorber assembly spring preload adjusting ring (page 3-16)
19. Brake pedal (page 3-11)
MY03 01-03 ING 6-10-2005 13:56 Pagina 13

1
2
3
4
5
6
7
8
9
10
PERIODIC MAINTENANCE AND MINOR REPAIR
ECA10010CAUTION:
Do not operate the vehicle until you
know that the engine oil level is suf-
ficient.
EWA10360
WARNING0
Never remove the engine oil tank
cap after high-speed operation,
otherwise hot engine oil could
spout out and cause damage or in-
jury. Always let the engine oil cool
down sufficiently before removing
the oil tank cap.
4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
5. Install the oil filler cap.
To change the engine oil
(with or without oil filter element
replacement)
1. Start the engine, warm it up for
several minutes, and then turn
it off.
2. Place the motorcycle on its side
stand, then place an oil pan under
the oil tank and another under the
engine to collect the used oil.
3. Remove the engine oil filler cap
and the drain bolt to drain the oil
from the crankcase.
4. Remove the drain bolt to drain the
oil from the oil tank.
1. Engine oil crankcase drain bolt
2. Engine oil tank drain bolt
5. Remove the oil filter element
drain bolt to drain the oil from the
oil filter element.
6-9
MY03 04-06 ING 6-10-2005 9:24 Pagina 6-9

NOTE:
Make sure that the O-rings are proper-
ly seated.
9. Install the oil drain bolts, and then
tighten them to the specified
torques.
PERIODIC MAINTENANCE AND MINOR REPAIR
1. Engine oil filter element drain bolt
2. Oil filter element cover bolts
NOTE:
Skip steps 6-8 if the oil filter element is
not being replaced.
6. Remove the oil filter element cov-
er by removing the bolts.
7. Remove and replace the oil filter
element and O-rings.
8. Install the oil filter element cover
by installing the bolts and the oil
filter element drain bolt, then
tightening them to the specified
torques.
1. Engine oil filter element
2. O-rings
6-10
1
2
3
4
5
6
7
8
9
10
Tightening torques:
Oil filter element cover bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Oil filter element drain bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Tightening torques:
Engine oil drain bolt (crankcase):
30 Nm (3.0 m·kgf, 22 ft·lbf)
Engine oil drain bolt (oil tank):
30 Nm (3.0 m·kgf, 22 ft·lbf)
10. Add the specified amount of the
recommended engine oil, and
then install and tighten the oil filler
cap.
MY03 04-06 ING 6-10-2005 9:24 Pagina 6-10