2007 YAMAHA MT-03 lights

1
2
3
4
5
6
7
8
9
10
INSTRUMENT AND CONTROL FUNCTIONS
3-9
EAU12343
Handlebar switches
Left
1. Pass switch “1”
2. Dimmer switch “2/ 1”
3. Horn switch “o”
4. Turn signal switch “y”
5. Hazard switch “
r”
Right
1. Engine stop switch “I/B”
2. Start switch “J”
EAU12350
Pass switch “1”
Press this switch to flash the head-
light.
EAU12400
Dimmer switch “2/1”
Set this switch to “
1” for the high
beam and to “2” for the low beam.
EAU12500
Horn switch “o”
Press this switch to sound the horn.
EAU12460
Turn signal switch “y”
To signal a right-hand turn, push this
switch to “∆”. To signal a left-hand
turn, push this switch to “Ÿ”. When re-
leased, the switch returns to the cen-
ter position. To cancel the turn signal
lights, push the switch in after it has
returned to the center position.
EAU12660
Engine stop switch “I/B”
Set this switch to “I” before starting the
engine. Set this switch to “
B” to stop
the engine in case of an emergency,
such as when the motorcycle overturns
or when the throttle cable is stuck.
EAU12710
Start switch “J”
Push this switch to crank the engine
with the starter.
ECA10050CAUTION:
See page 5-1 for starting instruc-
tions prior to starting the engine.
,
MY03 01-03 ING 6-10-2005 13:52 Pagina 3-9

INSTRUMENT AND CONTROL FUNCTIONS
3-10
1
2
3
4
5
6
7
8
9
10
EAU12733
Hazard switch “r”
With the key in the “ON” or Fposition,
use this switch to turn on the hazard
lights (simultaneous flashing of all turn
signal lights).
The hazard lights are used in case of
an emergency or to warn other drivers
when your vehicle is stopped where it
might be a traffic hazard.
ECA10061CAUTION:
Do not use the hazard lights for an
extended length of time with the
engine not running, otherwise the
battery may discharge.
EAU12820
Clutch lever
1. Clutch lever
The clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the han-
dlebar grip. To engage the clutch, re-
lease the lever. The lever should be
pulled rapidly and released slowly for
smooth clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
3-19).
EAU12870
Shift pedal
1. Shift pedal
The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 5-speed con-
stant-mesh transmission equipped on
this motorcycle.
MY03 01-03 ING 6-10-2005 13:52 Pagina 3-10

PRE-OPERATION CHECKS
4-4
1
2
3
4
5
6
7
8
9
10
ITEM
Instruments, lights,
signals and switches
Sidestand
switchCHECKS
• Check operation.
• Correct if necessary.
• Check operation of ignition circuit cut-off system.
• If system is defective, have Yamaha dealer check vehicle.PAGE
3-3, 3-9
3-20
MY03 04-06 ING 6-10-2005 9:24 Pagina 4

1
2
3
4
5
6
7
8
9
10
OPERATION AND IMPORTANT RIDING POINTS
EAU15950
EWA10270
WARNING0
Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer re-
garding any control or function
that you do not thoroughly un-
derstand.
Never start the engine or oper-
ate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of con-
sciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.
Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised com-
pletely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.
EAUB1340
Starting the engine
In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
The transmission is in the neutral
position.
The transmission is in gear with
the clutch lever pulled and the
sidestand up.
EWA10290
WARNING0
Before starting the engine,
check the function of the igni-
tion circuit cut-off system ac-
cording to the procedure de-
scribed on page 3-20.
Never ride with the sidestand
down.
1. Turn the key to “ON” and make
sure that the engine stop switch is
set to “
I”.
ECAB0040CAUTION:
The following warning lights and in-
dicator lights should come on for a
few seconds, then go off.
Neutral indicator light
Turn signal indicator light
High beam indicator light
Engine trouble warning light
Coolant temperature warning
light
Fuel level warning light
Immobilizer system indicator
light
If a warning or indicator light does
not go off, see page 3-3 for the cor-
responding warning and indicator
light circuit check.
2. Shift the transmission into the
neutral position.
5-1
MY03 04-06 ING 6-10-2005 9:24 Pagina 5-1

1
2
3
4
5
6
7
8
9
10
OPERATION AND IMPORTANT RIDING POINTS
ECA10260CAUTION:
Even with the transmission in
the neutral position, do not
coast for long periods of time
with the engine off, and do not
tow the motorcycle for long
distances. The transmission is
properly lubricated only when
the engine is running. Inade-
quate lubrication may damage
the transmission.
Always use the clutch while
changing gears to avoid dam-
aging the engine, transmission,
and drive train, which are not
designed to withstand the
shock of forced shifting.
EAU16810
Tips for reducing fuel
consumption
Fuel consumption depends largely on
your riding style. Consider the follow-
ing tips to reduce fuel consumption:
Shift up swiftly, and avoid high en-
gine speeds during acceleration.
Do not rev the engine while shift-
ing down, and avoid high engine
speeds with no load on the en-
gine.
Turn the engine off instead of let-
ting it idle for an extended length
of time (e.g., in traffic jams, at traf-
fic lights or at railroad crossings).
EAU16841
Engine break-in
There is never a more important peri-
od in the life of your engine than the
period between 0 and 1600 km (1000
mi). For this reason, you should read
the following material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts
in the engine wear and polish them-
selves to the correct operating clear-
ances. During this period, prolonged
full-throttle operation or any condition
that might result in engine overheating
must be avoided.
5-3
MY03 04-06 ING 6-10-2005 9:24 Pagina 5-3

1
2
3
4
5
6
7
8
9
10
PERIODIC MAINTENANCE AND MINOR REPAIR
6-56-5
NO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING (x 1,000 km)
110203040
ANNUAL
CHECK
• Check the air cut-off valve, reed valve, and hose
for damage.
• Check fuel hoses for cracks or damage.
• Check the screw clamp for looseness.
• Check operation.
• Adjust headlight beam. Air induction system
Muffler and exhaust
pipe
Lights, signals and
switches 28
✻
29✻
30✻
EAU18670
NOTE:
The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
Hydraulic brake service
Regularly check and, if necessary, correct the brake fluid level.
Every two years replace the internal components of the brake master cylinders and calipers, and change the brake
fluid.
Replace the brake hoses every four years and if cracked or damaged.√√√√ √
√√√√√
√√√√√ √
MY03 04-06 ING 6-10-2005 9:24 Pagina 6-5

MOTORCYCLE CARE AND STORAGE
7-1
1
2
3
4
5
6
7
8
9
10
EAU26000
Care
While the open design of a motorcycle
reveals the attractiveness of the tech-
nology, it also makes it more vulnera-
ble. Rust and corrosion can develop
even if high-quality components are
used. A rusty exhaust pipe may go un-
noticed on a car, however, it detracts
from the overall appearance of a mo-
torcycle. Frequent and proper care
does not only comply with the terms of
the warranty, but it will also keep your
motorcycle looking good, extend its
life and optimize its performance.
Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and cov-
ers as well as all electrical cou-
plers and connectors, including
the spark plug cap, are tightly in-
stalled.3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod-
ucts onto seals, gaskets, sprock-
ets, the drive chain and wheel
axles. Always rinse the dirt and
degreaser off with water.
Cleaning
ECA10770CAUTION:
Avoid using strong acidic
wheel cleaners, especially on
spoked wheels. If such prod-
ucts are used on hard-to-re-
move dirt, do not leave the
cleaner on the affected area
any longer than instructed. Al-
so, thoroughly rinse the area
off with water, immediately dry
it, and then apply a corrosion
protection spray.
Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use on-
ly a soft, clean cloth or sponge
with mild detergent and water
to clean plastic.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.
Do not use high-pressure
washers or steam-jet cleaners
since they cause water seep-
age and deterioration in the fol-
lowing areas: seals (of wheel
and swingarm bearings, fork
and brakes), electric compo-
nents (couplers, connectors,
instruments, switches and
lights), breather hoses and
vents.
MY03 07-10 ING 5-10-2005 17:09 Pagina 2

INDEX
1
2
3
4
5
6
7
8
9
10
Checking operation procedure .....3-20
Immobilizer system ............................3-1
Immobilizer system indicator light ......3-3
Indicator and warning lights ...............3-4
Coolant temperature warning
light .................................................3-4
Engine trouble warning light ...........3-4
Fuel level warning light ...................3-4
High beam indicator light ................3-4
Immobilizer system indicator light...3-3
Neutral indicator light ......................3-4
Turn signal indicator light................3-4
Indicator lights brightness
control mode ...................................3-8
Instruments ........................................2-3
Instrument and control functions ........3-1
K
Key identification number...................9-1
Keys ...................................................3-1
L
License plate light bulb, replacing....6-36
Lubricating the brake and
clutch levers ..................................6-26
Lubricating the brake pedal..............6-26
Lubricating the cables ......................6-25
Lubricating the drive chain ...............6-24
Lubricating the sidestand .................6-27
Lubricating the throttle grip and
cable .............................................6-25M
Main switch/steering lock ...................3-2
Model label .........................................9-2
Multi-function meter unit.....................3-5
Clock mode .....................................3-7
Indicator lights brightness
control mode ...................................3-8
Odometer, tripmeter modes ............3-6
Self-diagnosis devices ....................3-7
Tachometer .....................................3-6
N
Neutral indicator light .........................3-4
O
Odometer, tripmeter modes ...............3-6
Oil filter element ...............................6-10
Operation and important riding
points ..............................................5-1
Owner’s tool kit ..................................6-1
P
Panels, removing and installing .........6-6
Parking ...............................................5-4
Pass switch ........................................3-9
Periodic maintenance and
lubrication chart ..............................6-2
Periodic maintenance and minor
repair...............................................6-1
Pre-operation check list .....................4-2
Pre-operation checks .........................4-1R
Rear wheel .......................................6-38
Installing........................................6-38
Removing......................................6-38
Record the identification numbers .....9-1
S
Safety information ..............................1-1
Seats ................................................3-14
Self-diagnosis devices .......................3-7
Shift pedal ........................................3-10
Shifting ...............................................5-2
Shock absorber assembly
(adjusting) .....................................3-16
Side suspension, lubricating ............6-27
Sidestand .........................................3-18
Sidestand, checking and
lubricating .....................................6-27
Sidestand switch, checking ..............3-20
Spark plug, checking..........................6-6
Specifications .....................................8-1
Start switch.........................................3-9
Starting the engine .............................5-1
Steering, checking............................6-28
Steering lock ......................................3-2
Storage...............................................7-3
Supporting the motorcycle ...............6-36
T
Tachometer ........................................3-6
Tail/brake light bulb, replacing..........6-34
Throttle cable free play, adjusting ....6-15
MY03 07-10 ING 5-10-2005 17:09 Pagina 2