2007 YAMAHA GP1300R fuel

Features and functions
28

The current display will continue to operate
for 25 seconds after the engine stops.
EJU31460Tachometer
The engine speed (r/min) is displayed by seg-
ments. Each segment indicates a 250 r/min
increment.
EJU31500Speedometer
The meter shows the watercraft speed
against water.
NOTE:
To switch the speedometer display between
kilometers and miles, push the select button
for at least 1 second, within 10 seconds after
the meter is displayed.
EJU31510Fuel level meter
The fuel level meter is provided for convenient
fuel level checking while riding.The fuel level meter has eight segments
which show the amount of fuel remaining in
the fuel tank.
NOTE:
The fuel level is most accurate when the wa-
tercraft is sitting level on a trailer or in the wa-
ter.
EJU31530Hour meter/voltmeter
NOTE:
To switch the display between the hour meter
and the voltmeter, push the select button for
at least 1 second after the meter is displayed
for more than 10 seconds.
Hour meter
The hour meter is provided to make it easy to
follow the maintenance schedule.
1Select button
1Select button
UF1G74E0.book Page 28 Monday, July 31, 2006 10:10 AM

Features and functions
29
The meter shows the hours of engine opera-
tion that have elapsed since the watercraft
was new.
Voltmeter
The voltmeter is provided to display the volt-
age of the battery.
The voltmeter displays 12 volts or more when
the battery voltage is within specification.
If the voltage displayed is low, return to shore
and, if necessary, have a Yamaha dealer
check the charging system and the battery.
EJU31560Fuel level warning indicator
If the fuel remaining in the fuel tank drops to
about 13 L (3.4 US gal, 2.9 Imp gal), the low-
est two fuel level segments, the fuel level
warning indicator, and the “WARNING” light
begin to blink. The buzzer also starts sound-
ing intermittently.
If this occurs, refill the fuel tank as soon as
possible.
The warning signals will be cleared when the
engine is restarted after the fuel tank is re-
filled.
EJU31570Oil level warning indicator
If the oil remaining in the oil tank drops to
about 1.7 L (0.45 US gal, 0.37 Imp gal) or the
oil filter is clogged, the oil level warning indica-
tor and the “WARNING” light begin to blink.The buzzer also starts sounding intermittent-
ly.
If this occurs, refill the oil tank as soon as pos-
sible.
The warning signals will be cleared when the
engine is restarted after the oil tank is refilled.
NOTE:
If the oil level warning indicator and the
“WARNING” light blink when there is ade-
quate oil in the oil tank, have a Yamaha dealer
check the oil filter for dirt and clogs.
EJU31580Engine overheat warning indicator
This model is equipped with an engine over-
heat warning system.
If the engine starts to overheat, the “WARN-
ING” light and the engine overheat warning in-
dicator begin to blink, and the buzzer sounds
intermittently.
If this occurs, reduce the engine speed, return
to shore, and then check for water discharge
UF1G74E0.book Page 29 Monday, July 31, 2006 10:10 AM

Features and functions
31
speeds. If this occurs, the “WARNING” light
and the engine overheat warning indicator
come on and the buzzer sounds continuously.
In addition, the warning system will cut the ig-
nition to the engine to reduce the risk of se-
vere overheating. The engine cannot be
started until it cools down, so it may be neces-
sary to have the watercraft towed back to the
shore. (See “Towing the watercraft” on page
78 for towing procedures.)
The warning signals will be cleared when the
engine is restarted after it has cooled down.
NOTE:
If multiple warnings occur at the same time,
their priority is as follows:
(1) Final engine overheat warning
(2) Fuel level warning
(3) Oil level warning
(4) Initial engine overheat warning
(5) Exhaust temperature warning
(6) Check engine warning
EJU31610Exhaust temperature warning indicator
This model is equipped with an exhaust tem-
perature warning system.
If the exhaust temperature becomes too hot,
the “WARNING” light and the exhaust tem-
perature warning indicator begin to blink, and
the buzzer sounds intermittently.If this occurs, reduce the engine speed and
return to shore to allow the exhaust system to
cool down.
WARNING
EWJ00830
Do not touch the hot muffler or catalytic
converter during or immediately after en-
gine operation; they can cause serious
burns. In addition, the catalytic converter
becomes hotter after the engine stops be-
fore cooling down.
CAUTION:
ECJ00810
This model is equipped with a catalytic
converter.

If the “WARNING” light, exhaust temper-
ature warning indicator, and buzzer
come on, reduce the engine speed (be-
low 4000 r/min) and return to shore.

If you cannot locate and correct the
cause of the overheating, consult a
Yamaha dealer. Continuing to operate at
higher speeds could result in severe en-
gine damage.
The warning signals will be cleared when the
engine is restarted after it has cooled down.
EJU31630Check engine warning indicator
If a sensor malfunction or a short circuit is de-
tected, the “WARNING” light and the check
UF1G74E0.book Page 31 Monday, July 31, 2006 10:10 AM

Operation
35
EJU31800
Fuel and oil
This engine uses Yamaha’s oil injection sys-
tem, which provides superior lubrication by
ensuring the proper fuel-to-oil ratio for all op-
erating conditions. No fuel premixing is nec-
essary, except during the engine break-in
period. Simply pour gasoline into the fuel tank
and oil into the oil tank.
The engine utilizes an electronic fuel injection
system to deliver the optimal air-fuel ratio re-
quired by the engine. By ensuring the optimal
combustion conditions, this system is able to
increase startability and improve fuel econo-
my.
EJU31850Gasoline
WARNING
EWJ00440
GASOLINE AND ITS VAPORS ARE HIGH-
LY FLAMMABLE AND EXPLOSIVE!

Do not smoke when refueling, and keep
away from sparks, flames, and other
sources of ignition.

Stop the engine before refueling.

Refuel in a well-ventilated area with the
watercraft in a horizontal position.

Do not stand or sit on the watercraft
while refueling in case of fire.

Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags. Always properly dispose of
gasoline-soaked rags.

Avoid overfilling the fuel tank. Stop fill-
ing when the fuel level just reaches the
bottom of the filler tube. Do not fill up the
filler tube because fuel expands as it
warms up and could overflow. If tempo-
rarily leaving the watercraft with a full
fuel tank, do not leave it in direct sun-
light. Leave it in a well-ventilated areawith the watercraft in a horizontal posi-
tion.

Tighten the fuel tank filler cap securely
after refueling.

If you should swallow some gasoline, in-
hale a lot of gasoline vapor, or get gaso-
line in your eyes, get immediate medical
attention.

If any gasoline spills on your skin or
clothing, immediately wash the affected
area with soap and water and change
your clothes.
CAUTION:
ECJ00320

Do not use leaded gasoline. Leaded gas-
oline can seriously damage the catalytic
converter.

Use only fresh gasoline that has been
stored in clean containers.
EJU31860Gasohol
There are two types of gasohol: gasohol con-
taining ethanol and that containing methanol.
Gasohol containing ethanol can be used if
ethanol content does not exceed 10% and the
fuel meets the minimum octane ratings.
Gasohol containing methanol is not recom-
mended by Yamaha because it can cause
fuel system damage and engine performance
problems.Recommended gasoline:
Regular unleaded gasoline with a mini-
mum octane rating of
86 (Pump octane number) = (R +
M)/2
90 (Research octane number)
UF1G74E0.book Page 35 Monday, July 31, 2006 10:10 AM

Operation
36
EJU318802-stroke engine oil
CAUTION:
ECJ00270
Use only YAMALUBE 2-W engine oil, oth-
erwise the catalytic converter and other
engine components could be seriously
damaged.
NOTE:
YAMALUBE 2-W engine oil is developed for
this watercraft and available from a Yamaha
dealer.
EJU31920Filling the fuel tank
CAUTION:
ECJ00290
Be careful when refueling. Avoid getting
water and other contaminants in the fuel
tank. Contaminated fuel can cause poor
running and engine damage.
(1) Open the hood, remove the front storage
compartment, and then check the fuel
level. (See “Front storage compartment”
on page 32 for more information.)
(2) Remove the fuel tank filler cap, and then
slowly add fuel to the fuel tank. Stop fillingwhen the fuel level just reaches the bot-
tom of the filler tube.
(3) Install the fuel tank filler cap and front
storage compartment, and then close the
hood.
NOTE:
Do not fill up the filler tube because fuel ex-
pands as it warms up and could overflow.
EJU31960Filling the oil tank
WARNING
EWJ00420

Do not add gasoline to the oil tank. Fire
or explosion could result.

Oil in the bilge is a serious fire hazard.
Wipe up any spilled oil immediately.
CAUTION:
ECJ00300
Do not allow the oil tank to become com-
pletely empty. If the oil tank becomes emp-
ty, the oil pump must be bled to ensure
proper oil flow, otherwise engine damage
could result. If necessary, have a Yamaha
dealer bleed the oil pump.
(1) Remove the seat to view the oil level.
(See page 21 for seat removal and instal-
lation procedures.) Recommended engine oil:
YAMALUBE 2-W
Fuel tank capacity:
60.0 L (15.9 US gal) (13.2 Imp.gal)
UF1G74E0.book Page 36 Monday, July 31, 2006 10:10 AM

Operation
38
EJU31980
Pre-operation checks EJU31990Pre-operation check list
Before operating this watercraft, perform the checks in the following check list. See the accom-
panying text in this chapter for details on how to perform the checks.
WARNING
EWJ00410
If any item in the pre-operation check list is not working properly, have it inspected and
repaired before operating the watercraft, otherwise an accident could occur.
NOTE:
Pre-operation checks should be made each time the watercraft is used. These checks can be
completed in a short time. It is worth the time spent to ensure safety and reliability.
ITEM ROUTINE PAGE
BEFORE LAUNCH OR OPERATION
Engine compartmentRemove the seat and front storage compartment to
ventilate the engine compartment. Check for fuel va-
pors and loose electrical connections.39
BilgeCheck for water and fuel and drain if necessary. 39
Stern drain plugsCheck for proper installation. 40
Throttle leverCheck that the throttle lever springs back smoothly. 42
Steering systemCheck for proper operation. 42
QSTSCheck for proper operation. 42
Fuel and oilCheck the fuel and oil levels and replenish if neces-
sary.
Check the hoses and tanks for leakage.39
Water separatorCheck for water and drain if necessary. 39
BatteryCheck the electrolyte level and battery condition. 40
HoodCheck that the hood is securely closed. 21
SeatCheck that the seat is securely installed. 21
Hull and deckCheck the hull and deck for cracks and other dam-
age.39
Jet intakeCheck for debris and remove if necessary. 43
Fire extinguisherCheck the condition and replace if necessary. 41
Engine shut-off cordCheck the condition and replace if frayed or broken. 44
SwitchesCheck the start switch, engine stop switch, and en-
gine shut-off switch for proper operation.44
AFTER LAUNCH
Cooling water pilot outletCheck that water is discharged while the engine is
running and the watercraft is in the water.44
Multifunction information
centerCheck for warning indications and proper operation. 44
UF1G74E0.book Page 38 Monday, July 31, 2006 10:10 AM

Operation
39
EJU32280Pre-operation check points EJU32300Engine compartment
Ventilate the engine compartment before
each use.
To ventilate the engine compartment, remove
the seat and front storage compartment. (See
“Seat” on page 21 and “Front storage com-
partment” on page 32 for more information.)
Leave the engine compartment open for a few
minutes to allow any fuel vapors to escape.
While the engine compartment is open, check
for loose electrical connections.
WARNING
EWJ00460
Failure to ventilate the engine compart-
ment could result in a fire or explosion. Do
not start the engine if there is a fuel leak or
a loose electrical connection.
EJU32350Hull and deck
Check the hull and deck for cracks and other
damage. If any damage is found, have a
Yamaha dealer repair the watercraft.
EJU32371Fuel and oil systems
Check the fuel system for leakage, cracks,
and malfunctions before each use. (See page
66 for check points and correct procedures.)
(1) Remove the fuel tank filler cap to release
any pressure that might have built up in
the fuel tank.(2) Remove the seat and front storage com-
partment. (See “Seat” on page 21 and
“Front storage compartment” on page 32
for more information.)
(3) Check the fuel and oil levels in the tanks
and replenish if necessary. (See page 36
for refueling procedures and page 36 for
oil tank filling procedures.)
(4) Install the fuel tank filler cap, seat, and
front storage compartment.
EJU32420Water separator
Check the water separator for water. The wa-
ter separator retains any water that may have
entered through the fuel tank breather hose if
the watercraft was capsized. Normally, the
water separator is empty.
If water remains in the water separator, drain
it by removing the drain screw. Place a drain
pan under the water separator to catch the
draining water or use a dry cloth to soak up
any water that could spill into the watercraft. If
any water spills into the watercraft, be sure to
wipe it up with a dry cloth. Also, be sure to in-
stall the drain screw after draining the water
separator.
EJU32440Bilge
Check the bilge for moisture and fuel residue.
This watercraft is equipped with a convention-
al jet vacuum bilge draining system and an
1Water separator
2Drain screw
UF1G74E0.book Page 39 Monday, July 31, 2006 10:10 AM

Operation
45
tion on proper operation of the multifunction
information center.)EJU32740
Operation
WARNING
EWJ00510
Before operating your watercraft, become
familiar with all of the controls. Consult a
Yamaha dealer about any control or func-
tion that you do not fully understand. Fail-
ure to understand how the controls work
could cause an accident or prevent you
from avoiding an accident.
CAUTION:
ECJ00460
Make sure that the stern drain plugs are
tightened securely before launching the
watercraft.
EJU32760Engine break-in
The engine break-in period is essential to al-
low the various components of the engine to
wear and polish themselves to the correct op-
erating clearances. This ensures proper per-
formance and promotes longer component
life.
CAUTION:
ECJ00450

For the first tankful of fuel, premix the
fuel in a fuel-to-oil ratio of 50:1 (in addi-
tion to the oil in the oil tank).

After break-in, use straight gasoline for
normal operation.
UF1G74E0.book Page 45 Monday, July 31, 2006 10:10 AM