2007 VOLVO C70 CONVERTIBLE homelink

2007 Volvo C70
1-800-663-8255
www.volvocanada.com
2006 © Volvo Car Corporation. All rights reserved.
2 Contents

00 Introduction
General information
6
Volvo and the environment
7
Important warnings
9

01 Safety
Occupant safety
12
Seat belts
14
Supplemental Restraint System
17
Front airbags
18
Occupant Weight Sensor
21
Side impact protection airbags
24
Door mounted inflatable curtains
25
Whiplash Protection System
26
Roll-over Protection System
28
Crash mode
29
Child safety
30
Child restraint systems
33
Infant seats
35
Convertible seats
37
Booster cushions
39
ISOFIX lower anchors
40

02 Instrument and controls
Instrument overview
44
Instrument panel
57
Symbols - instrument panel
50
Information display
53
Lighting panel
55
Left-side steering wheel lever
57
Trip computer
58
Right-side steering wheel lever
60
Cruise control
62
Right-side steering wheel keypad
64
Steering wheel adjustment,
Hazard warning flashers
65
Parking brake
66
12-volt sockets
67
Power windows
68
Mirrors
69
Personal settings
72
HomeLink® Universal
Transceiver (option)
74
file:///K|/delme/2007_C70/07c70_00.htm (2 of 7)12/22/2006 9:15:34 PM

2007 Volvo C70
2 0 0 7
VOLVO C70
42 02 Instruments and controls
Instrument overview
44
Instrument panel
47
Symbols - instrument panel
50
Information display
53
Lighting panel
55
Left-side steering wheel lever
57
Trip computer
58
Right-side steering wheel lever
60
Cruise control
62
Right-side steering wheel keypad
64
Steering wheel adjustment, Hazard warning flashers
65
Parking brake
66
12-volt sockets
67
Power windows
68
Mirrors
69
Personal settings
72
HomeLink® Universal Transceiver (option)
74
43 02 Instruments and controls
44 02 Instruments and controls
file:///K|/delme/2007_C70/07c70_02.htm (1 of 43)12/22/2006 9:15:41 PM

2007 Volvo C70
l VIN number:
The VIN (Vehicle Identification Number) is the car's unique identity n\
umber.
l Number of Keys:
The number of keys registered for the car is displayed here.
Climate functions
l Blower speed in AUTO mode:
The blower speed can be set to AUTO mode in models equipped with ECC. Ch\
oose between "Low", "Normal" and
"High".
l Timer for recirculation:
When the timer is active, the air recirculates in the car for 3-12 minut\
es depending on the ambient temperature. Select
On/Off depending on whether the recirculation timer is to be active or n\
ot.
Reset to factory settings
Use this alternative to return to the default climate system settings.
74 02 Instruments and controls
HomeLink® Universal Transceiver (option)
02 Introduction
HomeLink1 is a system that can be programmed to learn the codes of three differen\
t remote controlled-devices (for
example, a garage door opener, remote lighting, entry gate). HomeLink's\
sun visor-mounted transceiver, powered by
your car's electrical system, may then be used in place of your handheld\
remote controls. The HomeLink transceiver
consists of three programmable buttons and an indicator light.
1 HomeLink is a registered trademark of Johnson Controls, Intl.
© JCI, All rights reserved
file:///K|/delme/2007_C70/07c70_02.htm (38 of 43)12/22/2006 9:15:42 PM\

2007 Volvo C70
NOTE
l For your security, the HomeLink Universal Transceiver is designed to not\
function if you lock your car from the
outside.
l Retain the original transmitter(s) for future programming procedures (\
for example, if you purchase a new
vehicle).
l For your own security, erase all programmed buttons on the HomeLink Univ\
ersal Transceiver when you sell your
vehicle.
l Metallic sun protection films should not be used on any windows in a veh\
icle equipped with HomeLink Universal
Transceiver. This could interfere with the transceivers function.
Operating the HomeLink Universal Transceiver
Once programmed, the HomeLink Universal Transceiver can be used in place\
of your handheld transmitters.
NOTE
The HomeLink universal transceiver will function for 30 minutes after th\
e driver's door has been opened without
switching on the vehicle's ignition.
Press the programmed HomeLink button to activate the garage door, drivew\
ay gate, security lightning, home security
system etc.
Your original hand-held transmitters may, of course, be used at any time\
.
WARNING
l If you use HomeLink to open a garage door or gate, be sure no one is nea\
r the gate or door while it is in motion.
l Do not use the HomeLink Universal Transceiver with any garage door opene\
r that lacks safety "stop" and
"reverse" features as required by federal safety standards. (This inclu\
des any garage door opener model
manufactured before April 1, 1982). A garage door opener that cannot "d\
etect" an object, signalling the door to
"stop" and "reverse" does not meet current federal safety standards. Usi\
ng a garage door opener without these
features increases the risk of serious injury or death. For more informa\
tion on this matter, call toll-free 1-800-355-
3515. (Internet:
www.HomeLink.com).
Programming the transceiver for the first time (U.S. residents)
1. For first time training, press and hold the two outer HomeLink button\
s, releasing only when the HomeLink
indicator light begins to flash after 20 seconds. (Do not perform this \
step when training the additional HomeLink
buttons.)
2. Position the hand-held transmitter 1-3 inches away from the HomeLink \
surface
75 02 Instruments and controls
HomeLink® Universal Transceiver (option)
file:///K|/delme/2007_C70/07c70_02.htm (39 of 43)12/22/2006 9:15:42 PM\

2007 Volvo C70
(located on your sun visor), keeping the HomeLink indicator light in v\
iew.
3. Using both hands, simultaneously press and hold both the desired Home\
Link button and hand held transmitter
button. DO NOT release until the HomeLink indicator light flashes slowly\
and then rapidly. When the indicator light
flashes rapidly, both buttons may be released. (The rapid flashing indi\
cates successful training.)
NOTE
Some garage door openers may require you to replace step 3 with the "cyc\
ling" procedure noted in the
"Programming the transceiver for the first time (Canadian residents)" \
section.
4. Press and hold the trained HomeLink button and observe the indicator \
light.
l If the indicator light is solid/continuous, training is complete and you\
r device should activate when the HomeLink
button is pressed and released.
l If the indicator light blinks rapidly for 2 seconds and then turns a sol\
id/continuous light, proceed with the following
training instructions for a rolling code device. A second person may mak\
e the following steps quicker and easier.
Please use a ladder or other device. Do not stand on your vehicle to per\
form the next steps.
5. At the garage door opener receiver (motorhead unit) in the garage, \
locate the "learn" or "smart" button (usually near
where the hanging antenna wire is attached to the unit). If there is di\
fficulty locating the training button, reference the
garage door opener's manual or contact us toll-free 1-800-355-3515 (Int\
ernet:
www.HomeLink.com).
6. Press and release the "learn" or "smart" button (the name and color \
of the button may vary by manufacturer).
NOTE
Once the button is pressed, there are 30 seconds in which to initiate th\
e next
step.
7. Return to the vehicle and firmly press and hold the trained HomeLink \
button for two seconds and release. Repeat
the "press/hold/release" sequence up to 3 times to complete the training\
process.
To train additional HomeLink buttons, begin with step two.
Programming the transceiver for the first time (Canadian residents)
1. For first time training, press and hold the two outer HomeLink button\
s releasing only when the HomeLink indicator
light begins to flash after 20 seconds. (Do not perform this step when \
training the additional HomeLink buttons.)
2. Position the hand-held transmitter 1-3 inches (2.5-7.5 cm) away fro\
m the HomeLink surface (located on your)
keeping the HomeLink indicator light in view.
3. Using both hands, simultaneously press and hold both the desired Home\
Link button and hand held transmitter
button. During programming, your handheld transmitter may automatically \
stop transmitting. Continue to press and
hold the desired HomeLink button while you press and re-press ("cycle")\
your handheld transmitter every two
file:///K|/delme/2007_C70/07c70_02.htm (40 of 43)12/22/2006 9:15:42 PM\

2007 Volvo C70
seconds until the frequency signal has been learned. The indicator light\
will flash slowly and then rapidly after several
seconds upon successful training. DO NOT release until the HomeLink indi\
cator light flashes slowly and then rapidly.
When the indicator light flashes rapidly, both buttons may be released. \
(The rapid flashing indicates successful
training.)
76 02 Instruments and controls
HomeLink® Universal Transceiver (option)
4. Press and hold the trained HomeLink button and observe the indicator \
light.
l If the indicator light is solid/continuous, training is complete and you\
r device should activate when the HomeLink
button is pressed and released.
l If the indicator light blinks rapidly for 2 seconds and then turns a sol\
id/continuous light, proceed with the following
training instructions for a rolling code device. A second person may mak\
e the following steps quicker and easier.
Please use a ladder or other device. Do not stand on your vehicle to per\
form the next steps.
5. At the garage door opener receiver (motorhead unit) in the garage, \
locate the "learn" or "smart" button (usually near
where the hanging antenna wire is attached to the unit). If there is di\
fficulty locating the training button reference the
garage door opener's manual or contact us.
6. Press and release the "learn" or "smart" button (the name and color \
of the button may vary by manufacturer).
NOTE
Once the button is pressed, there are 30 seconds in which to initiate th\
e next
step.
7. Return to the vehicle and firmly press and hold the trained HomeLink \
button for two seconds and release. Repeat
the "press/hold/release" sequence up to 3 times to complete the training\
process.
NOTE
During programming, your hand-held transmitter may automatically stop tr\
ansmitting. Continue to press and hold
the desired HomeLink button while you press and repress ("cycle") your\
hand-held transmitter every two seconds
until the frequency signal has been learned. The indicator light will fl\
ash slowly and then rapidly after several
seconds upon successful training. If necessary, follow steps 5-7 to comp\
lete the training for a rolling code device.
To train additional HomeLink buttons, begin with step two.
Rolling Code Programming
Rolling code garage door openers that are "code-protected" and manufactu\
red after 1996 may be determined by the-
following:
l Reference the garage door opener owner's manual for verification.
l The handheld transmitter appears to program the HomeLink Universal Trans\
ceiver but does not activate the garage
door.
file:///K|/delme/2007_C70/07c70_02.htm (41 of 43)12/22/2006 9:15:42 PM\

2007 Volvo C70
l Press and hold the trained HomeLink button. The garage door opener has t\
he rolling code feature if the indicator
light flashes rapidly and then turns solid after 2 seconds.
To train a garage door with the rolling code feature, follow these instr\
uctions (the aid of a second person may make
the training quicker and easier):
1. Locate the training button on the garage door opener motor head unit.\
Exact location and color of the button may
vary by garage door opener brand. If there is difficulty locating the tr\
aining button, reference the garage door opener
owner's manual or please visit our Web site at
www.homelink.com.
2. Press the training button on the garage door opener motor head unit (\
which activates the "training light").
NOTE
Following step 2, there are 30 seconds in which to initiate step
3.
3. Firmly press and release the programmed HomeLink® button. Press an\
d release the HomeLink button a second
time to complete the training process. (Some garage door openers may re\
quire
77 02 Instruments and controls
HomeLink® Universal Transceiver (option)
you to do this procedure a third time to complete the training.)
The garage door opener should now recognize the HomeLink Wireless Contro\
l System. The remaining two buttons
may now be trained if this has not previously been done. Refer to the Pr\
ogramming portion of this text. The
HomeLink Wireless Control System (once programmed) or the original han\
dheld transmitter may be used to activate
the garage door. In the event that there are still difficulties in progr\
amming the HomeLink Wireless Control System,
please visit our Web site,
www.homelink.com.
Reprogramming a Single HomeLink Button
To program a device to HomeLink using a HomeLink button previously train\
ed, follow these steps:
1. Press and hold the desired HomeLink button. Do NOT release until step\
4 has been completed.
2. When the indicator light begins to flash slowly (after 20 seconds),\
position the handheld transmitter 1 to 3 inches
away from the HomeLink surface.
3. Press and hold the handheld transmitter button. The HomeLink indicato\
r light will flash, first slowly and then
rapidly.
4. When the indicator light begins to flash rapidly, release both button\
s.
file:///K|/delme/2007_C70/07c70_02.htm (42 of 43)12/22/2006 9:15:42 PM\

2007 Volvo C70
The previous device has now been erased and the new device can be activa\
ted by pushing the HomeLink button that
has just been programmed. This procedure will not affect any other progr\
ammed HomeLink.
Erasing Channels
Individual buttons cannot be erased. However, to erase all three program\
med buttons:
1. Press and hold the two outside buttons until the indicator light begi\
ns to flash (after 20 seconds).
2. Release both buttons.
The HomeLink® Wireless Control System is now in the training (learni\
ng) mode and can be programmed at any time
following steps 2 through 4 in the Programming section.



Contents | Top of Page
file:///K|/delme/2007_C70/07c70_02.htm (43 of 43)12/22/2006 9:15:42 PM\