2007 TOYOTA TUNDRA air conditioning

3782007 TUNDRA from Jul. ’07 Prod. (OM34463U)
1. Fan speed selector
2. “A/C” button
3. Air intake selector
4. Temperature selector (passenger sidetemperature control)
5. Air flow selector
6. Temperature selector (driver side temperature control)
Manual air conditioning system—
—Controls
XS19019

3792007 TUNDRA from Jul. ’07 Prod. (OM34463U)
Fan speed selector
Turn the knob to adjust the fan speed—to
the right to increase, to the left to de-
crease.
Temperature selector (driver side)
Turn the knob to adjust the temperature—
to the right to warm, to the left to cool.
“MAX A/C” position—Turning the tempera-
ture selector knob to the “MAX A/C” posi-
tion turns on the air conditioning and sets
the air intake selector to RECIRCULATE
for quick cooling.Temperature selector (passenger side)
Turn the knob to adjust the tempera-
ture—to the right to warm, to the left to
cool.
Independent setting—
When the passenger side selector is
in a position other than the “SYNC”
position, the temperature only on pas-
senger side can be adjusted using the
selector. This function is canceled
when the passenger side temperature
selector is turned to the “SYNC” posi-
tion.
Simultaneous setting— When the passenger side selector is
in the “SYNC” position, the tempera-
tures on both driver and passenger
sides can be simultaneously adjusted
using the driver side selector. This
function is canceled when the passen-
ger side temperature selector is
turned to the right.
G18021
Air flow selector
Turn the knob to select the vents used for
air flow.
1. Panel— Air flows mainly from the
instrument panel vents and the rear
vents.
2. Bilevel— Air flows from both the floor
vents, the instrument panel vents and
the rear vents.
3. Floor— Air flows mainly from the floor
vents.

3802007 TUNDRA from Jul. ’07 Prod. (OM34463U)
4. Floor/Windshield—Air flows mainly
from the floor vents and windshield
vents.
Turning the air flow selector to the
floor/windshield position turns on the
defogging/defrosting function with the
purpose of clearing the windshield.
In this position, air intake selector
mode changes to FRESH automatically
to clear the windshield quickly. If you
want to return the setting to RECIRCU-
LATE mode, press the air intake selec-
tor button once again.
Press the “A/C” button for dehumidified
heating or cooling. This setting clears
the windshield more quickly.
5. Windshield— Air flows mainly from the
windshield vents.
Turning the air flow selector to the
windshield position turns on the defog-
ging/defrosting function and the air con-
ditioning with the purpose of clearing
the windshield.
In this position, air intake selector
mode changes to FRESH automatically
to clear the windshield quickly. It is not
possible to return to RECIRCULATE in
this position. In this position, the air conditioning
turns on regardless of the “A/C button
indicator comes on or goes off. This is
not a malfunction.
For details about air flow selector settings,
see “Air flow selector settings” described
below.
XS19014
Air intake selector
Press the button to select the air source.
1. Recirculate (indicator light is on)—Re-
circulates the air inside the vehicle.
2. Fresh (indicator light is off)—Draws
outside air into the system.
To prevent fogging up of the windshield,
the air intake mode may change automati-
cally to FRESH depending on the condi-
tion of the air conditioning system.

3812007 TUNDRA from Jul. ’07 Prod. (OM34463U)
If the ambient temperature drops, the air
intake mode will automatically change
from RECIRCULATE to FRESH after a few
minutes. This automatic change control
mode can be cancelled by pushing and
holding the button for longer than 2 sec-
onds. The automatic change control mode
will be reactivated if the ignition switch is
turned to the “LOCK” or “ACC” position.
“A/C” button
To turn on the air conditioning, press the
“A/C” button. The “A/C” button indicator
will come on. To turn the air conditioning
off, press the button again.
If the “A/C” button indicator flashes, there
is a problem in the air conditioning system
and the air conditioning automatically
shuts off. If this happens, take your ve-
hicle to a Toyota dealer for service.

3822007 TUNDRA from Jul. ’07 Prod. (OM34463U)
:driver side :passenger side
To cool off your Toyota after it has
been parked in the hot sun, drive with
the windows open long enough for the
hot air to escape. This operation allows
the air conditioning to cool the interior
more quickly.
Make sure the air intake grilles in front
of the windshield are not blocked (by
leaves or snow, for example).
On humid days, do not blow cold air
on the windshield. The windshield could
fog up because of the difference in air
temperature on the inside and outside
of the windshield.
Keep the area under the front seats
clear to allow air to circulate through-
out the vehicle.
On cold days, set the fan speed to
high for a minute to help clear the
intake ducts of snow or moisture. This
can reduce the amount of fogging on
the windows.
When driving on dusty roads, close all
windows. If dust thrown up by the ve-
hicle is still drawn into the vehicle after
closing the windows, it is recommended
that the air intake selector be set to
FRESH and the fan speed selector to
any setting except “OFF”.
—Air flow selector settings—Operating tips
XS19021
∗
1: Double cab and Crew Max models
∗1
∗ 1 ∗
1
∗2
: Crew Max models
∗1 ∗
1
∗2
∗2
∗ 2
∗ 2
∗1

3832007 TUNDRA from Jul. ’07 Prod. (OM34463U)
If following another vehicle on a dusty
road, or driving in windy and dusty
conditions, it is recommended that the
air intake selector be temporarily set to
RECIRCULATE, which will close off the
outside passage and prevent outside
air and dust from entering the vehicle
interior.Heating
For best results, set controls to:
Fan speed— Any setting except “OFF”
Temperature— Towards red zone
Air intake—FRESH (outside air)
Air flow—FLOOR
Air conditioning—OFF
For quick heating, select recirculated
air for a few minutes. To keep the
windows from fogging, select fresh af-
ter the vehicle interior has been
warmed.
Press the “A/C” button on for dehumidi-
fied heating.
Choose floor/windshield air flow to heat
the vehicle interior while defrosting or
defogging the windshield. Air conditioning
For best results, set controls to:
Fan speed— Any setting except “OFF”
Temperature— Towards blue zone
Air intake—FRESH (outside air)
Air flow—PANEL
Air conditioning—ON

3842007 TUNDRA from Jul. ’07 Prod. (OM34463U)
XS19013a
For quick cooling, turn the temperature
selector knob to the “MAX A/C” posi-
tion. The air conditioning will automati-
cally turn on and the air intake selector
will be set to RECIRCULATE.
Ventilation
For best results, set controls to:
Fan speed— Any setting except “OFF”
Temperature— Towards blue zone
Air intake—FRESH (outside air)
Air flow—PANEL
Air conditioning—OFF
Defogging
Condition: Moisture is on the inside of the
windshield.
For best results, set controls to:
Fan speed— Any setting except “OFF”
Temperature— Towards red zone to heat;
blue zone to cool
Air intake—FRESH (outside air)
Air flow—WINDSHIELD
Turning the air flow selector to the wind-
shield or floor/windshield position turns on
the defogging function with the purpose of
clearing the windshield.
When turning the air flow selector to wind-
shield or floor/windshield position, air in-
take selector mode changes to FRESH
automatically to clear the windshield
quickly. If you want to return the setting
to RECIRCULATE mode, press the air in-
take selector button once again. However,
if the air flow selector is in the windshield
position, it is not possible to return to
RECIRCULATE.
Press the “A/C” button for dehumidified
heating or cooling. This setting clears the
front view more quickly.
On humid days, do not blow cold air
on the windshield—the difference be-
tween the outside and inside tempera-
tures could make the fogging worse.
When side windows fog up, turn the
side vents toward the windows.
Defrosting
Condition: Moisture is on the outside of
the windshield.
For best results, set controls to:
Fan speed— Any setting except “OFF”
Temperature— Towards red zone
Air intake—FRESH (outside air)
Air flow—WINDSHIELD
Turning the air flow selector to the wind-
shield or floor/windshield position turns on
the defrosting function with the purpose of
clearing the windshield.
When turning the air flow selector to wind-
shield or floor/windshield position, air in-
take selector mode changes to FRESH
automatically to clear the windshield
quickly. If you want to return the setting
to RECIRCULATE mode, press the air in-
take selector button once again. However,
if the air flow selector is in the windshield
position, it is not possible to return to
RECIRCULATE.

3862007 TUNDRA from Jul. ’07 Prod. (OM34463U)
1. Fan speed selector
2. “AUTO” button
3. Temperature selector (“TEMP”)(with “DUAL” button indicator
on—individual setting on driver and front
passenger)
(with “DUAL” button indicator
off—simultaneous setting on driver and
front passenger)
4. “A/C” button
5. Air flow selector
6. Windshield air flow button
7. Temperature selector (“PASS TEMP”)
(individual setting on front passenger
side only)
8. “DUAL” button
9. Air intake selector
10. “OFF” button
Automatic air conditioning system
(on some Double cab and Crew Max models)—
—Controls
XS19020a