2007 TOYOTA CAMRY ECU

’07Camry_U (L/O 0608)
168
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
Move the selector lever down to the
“−” side to select the “1” range. The
downshift to first range when the ve-
hicle speed drops down to or lower
than 38 km/h (24 mph), and maximum
engine braking will be enabled.
CAUTION
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to skid or
spin.
(e) Backing up
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with
your foot, shift the selector lever to the
“R” position.
NOTICE
Never shift into reverse while the ve-
hicle is moving.
(f) Parking
1. Bring the vehicle to a complete stop.
2. With the brake pedal pressed down,
fully depress the parking brake pedal
to apply the parking brake securely.
3. With the brake pedal pressed down,
shift the selector lever to the “P” posi-
tion.
CAUTION
Never attempt to move the selector
lever into “P” position under any cir-
cumstances while the vehicle is mov-
ing. Serious mechanical damage and
loss of vehicle control may result.
(g) Good driving practice
If the transmission repeatedly shifts up
and down between third gear and over-
drive when climbing a gentle slope,
shift the selector lever into sequential
position.
When towing a trailer, in order to main-
tain engine braking efficiency, do not
use overdrive.
CAUTION
Always keep your foot on the brake
pedal while stopped with the engine
running. This prevents the vehicle
from creeping.
NOTICE
Always use the brake pedal or the
parking brake to hold the vehicle on
an upgrade. Do not attempt to hold
the vehicle using the accelerator ped-
al, as this can cause the transmission
to overheat.
(h) If you cannot shift the selector le-
ver out of “P” position
If you cannot shift the selector lever from
the “P” position even though the brake
pedal is depressed, use the shift lock
override button. For instructions, see “If
you cannot shift automatic transmission
selector lever” on page 355 in Section 4.

’07Camry_U (L/O 0608)
178
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
NOTICE:
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable protec-
tion against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed
and used in accordance with the instruc-
tions, may cause harmful interference to
radio communications. However, there is
no guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful interfer-
ence to radio or television reception,
which can be determined by turning the
equipment off and on, the user is en-
couraged to try to correct the interfer-
ence by one or more of the following
measures:
−Reorient or relocate the receiving an-
tenna.
−Increase the separation between the
equipment and receiver.−Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
−Consult the dealer or an experienced
radio/TV technician for help.
FCC WARNING:
Changes or modifications not ex-
pressly approved by the party respon-
sible for compliance could void the
user’s authority to operate the equip-
ment.
For vehicles sold in Canada
Operation is subject to the following two
conditions: (1) this device may not
cause interference, and (2) this device
must accept any interference, including
interference that may cause undesired
operation of the device.
REPLACING TIRES AND WHEELS
When replacing the tires and wheels, be
sure to install tire pressure warning valves
and transmitters. ID codes on the tire
pressure warning valves and transmitters
are registered on the tire pressure warning
ECU. When replacing a tire pressure
warning valve and transmitter, it is neces-
sary to register the ID code of tire pres-
sure warning valve and transmitter. Have
the ID code registered by your Toyota
dealer.
NOTICE
When the tires or tire pressure warn-
ing valves and transmitters must be
replaced, have them replaced by your
Toyota dealer. The tire pressure warn-
ing valves and transmitters will be
affected by the installation or removal
of tires.

’07Camry_U (L/O 0608)
198
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
1 2 3 4 5 6 (Preset buttons)
These buttons are used to preset and
tune in radio stations.
To preset a station to a button: Tune in
the desired station. (See “TUNE·FILE” or
“SEEK·TRACK”.) Push and hold down the
button until you hear a beep—this will set
the station to the button. The preset but-
ton number will appear on the display.
To recall a preset station: Push the button
for the station you want. The preset but-
ton number and station frequency will ap-
pear on the display.
These systems can store one AM and two
FM stations for each button. (The display
will show “AM”, “FM1” or “FM2” when you
push “AM·SAT”, “FM1” or “FM2” button.)
XM satellite radio
∗—
These buttons are used to preset and
tune in radio channels.
To preset a channel to a button: Tune in
the desired channel. (See “TUNE·FILE” or
“SEEK·TRACK”.) Push and hold down the
button until you hear a beep—this will set
the channel to the button. The preset but-
ton number will appear on the display.To recall a preset channel: Push the but-
ton for the channel you want. The preset
button number and channel number will
appear on the display.
This radio can store three XM channels
for each button. (The display will show
“SAT1”, “SAT2” or “SAT3” when you push
“AM·SAT” button.)
∗: Use of satellite radio requires XM tuner
and service. Contact your Toyota deal-
er for details.
(Eject button)
This button is used to eject one or all
compact discs.
To eject the current compact disc, push
and release the compact disc eject button.
To eject a specific disc, push “” (preset
button 3) or “” (preset button 4) until the
number of the disc you want to eject is
displayed. Push and release the eject but-
ton.
To eject all discs at a time, press and
hold the eject button until you hear a
beep. The last compact disc played before
pushing the button will be ejected first. If
the ejected disc is not removed for a long
time, the eject function will be cancelled.
(Reverse/Fast forward button)
Push and hold “
” (preset button 6) or
“
” (preset button 5) to fast forward or
reverse within a compact disc. When you
release the button, the player will resume
playing.
AM·SAT (AM band and XM satellite ra-
dio
∗)
Push the “AM·SAT” button to turn on the
radio and select the AM or XM band.
“AM”, “SAT1”, “SAT2” or “SAT3” will ap-
pear on the display.
Error messages
If the satellite radio tuner malfunctions,
your audio system will display following
error messages.
“ANTENNA”:
The XM antenna is not connected.
Check whether the XM antenna cable
is attached securely.
A short−circuit occurs in the antenna or
the surrounding antenna cable. See a
Toyota certified dealer.

’07Camry_U (L/O 0608)
215
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
WMA—
WMA (Windows Media Audio) is an audio
compression format developed by Micro-
soft. It compresses files into a size small-
er than that of MP3 files. The decoding
formats for WMA files are Ver. 7, 8, and
9.Phone Setup (see page 221)
Pair phone
To use the hands−free system, you
need to register your phone in the sys-
tem.
Change name
The registered phone names can be
changed.
Delete
The registered phones can be deleted.
List phones
The registered phone names can be
checked.
Select phone
The registered phones can be selected.
Set passkey
The passkey can be changed.Security (see page 226)
Set PIN
The PIN can be set or changed.
Phone book lock
The phone book can be locked.
Phone book unlock
The locked phone book can be un-
locked.
System Setup (see page 230)
Adjust Guidance Volume
Guidance volume can be adjusted.
Initialize
Phone Book (see page 230)
Add Entry
Phone numbers and voice tags can be
registered.
Change Name
The registered names can be changed.
Delete Entry
The registered names can be deleted.
Handsfree phone system—
—Reference

’07Camry_U (L/O 0608)
217
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
The system may not function in the follow-
ing conditions and places:
The cellular phone is turned off.
The current position is outside the
communication area.
The cellular phone is not connected.
The cellular phone has a low battery.
The cellular phone is hiding behind the
seat or in the glove box and console
box.
The cellular phone touches or is cov-
ered with metal materials.
This system supports the following ser-
vice.
HFP (Hands Free Profile) Ver. 1.0
OPP (Object Push Profile) Ver. 1.1
If your cellular phone does not support
HFP, you cannot enter the Bluetooth
phone, and take OPP service individually.
BLUETOOTH is a trademark owned by
Bluetooth SIG. Inc.When transferring ownership of the ve-
hicle:
A lot of personal data is registered
when you use the handsfree system.
When transferring ownership of the ve-
hicle, initialize the system.
If you initialize it, the former state will
never come back again. Pay much atten-
tion when initializing the data.
You can initialize the following data in the
system.
Phone book data
Dialed numbers and received calls
Speed dial
Bluetooth phone data
Security code
FCC ID: HYQBTAU01A
IC ID: 1551ABTAU01A
MADE IN JAPAN
This device complies with Part 15 of the
FCC Rules and RSS−210. Operation is
subject to the following two conditions:
(1) This device may not cause harmful
interference, and (2) This device must
accept any interference received, includ-
ing interference that may cause unde-
sired operation.
CAUTION
Changes or modifications not ex-
pressly approved by the party respon-
sible for compliance could void the
user’s authority to operate the equip-
ment.

’07Camry_U (L/O 0608)
222
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
Set PassKey
The passkey can be changed. A 4 to 8
digit code can be input as a passkey.
Delete
The registered phones can be deleted.
To enter the phone setup menu
1. Push the off−hook switch to turn the
hands−free system on.
2. Follow voice guidance instructions, or
turn the “AUDIO CTRL” knob until
“Setup” is displayed and push the
knob.
“Setup. Please push the talk switch and
say security, or phone setup.” is heard.
3. Follow voice guidance instructions, or
turn the “AUDIO CTRL” knob until
“Phone Setup” is displayed and push
the knob.
“Phone setup. Push the talk switch and
say pair phone, select phone, change
name, list phones, set passkey or delete.”
is heard.
“XXX (phone name) already selected.” is
heard and “XXX (phone name)” is dis-
played.
If no phone has been registered, the sys-
tem may not function properly.To pair phones
1. Push the talk switch and say “Pair
phone”, or turn the “AUDIO CTRL”
knob until “Pair Phone” is displayed
and push the knob.
“Pair. Push the talk switch and say a
name for the phone.” is heard.
2. Follow voice guidance instructions, or
turn the “AUDIO CTRL” knob until
“Record Name” is displayed, push the
knob and say “XXX (desired phone
name)”.
“Push the talk switch and say confirm.
Otherwise, say go back.” is heard.
3. Follow voice guidance instructions, or
turn the “AUDIO CTRL” knob until
“Confirm” is displayed and push the
knob.
“XXX Ready for phone pairing. Please use
the phone to connect it to the hands−free
system. The passkey for the phone is....”
is heard.
After “HANDS FREE” is displayed, a pass-
key
∗ is displayed and “Searching.” is
heard.
4. Input the displayed passkey into the
phone.“The phone is paired and ready for use.
Returning to the main menu.” is heard and
“Paired” is displayed.
The system may not function in the follow-
ing cases:
If 6 phones have already been regis-
tered.
If the vehicle is moving.
If the system cannot communicate with
the phone.
∗: Passkey is a password required to reg-
ister a phone to the system.
INFORMATION
To use the handsfree system, you
need to register your phone in the
system. Once you have registered
it, you can make a handsfree call.
Up to 6 phones can be registered.
For the operation of the phone, see
the manual that comes with your
cellular phone.
The passkey can be changed. See
page 225 for changing the passkey.

’07Camry_U (L/O 0608)
226
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
To delete a phone
1. Push the talk switch and say “Delete”,
or turn the “AUDIO CTRL” knob until
“Delete” is displayed and push the
knob.
“Delete. Push the talk switch and say the
phone name to delete.” is heard.
2. Follow voice guidance instructions, or
turn the “AUDIO CTRL” knob until the
phone name you want to delete is dis-
played and push the knob.
When using a voice command:
“XXX Push the talk switch and say con-
firm. Otherwise, say go back.” is heard
and “XXX” is displayed.
Follow voice guidance instructions, or turn
the “AUDIO CTRL” knob until “Confirm” is
displayed and push the knob.
“Deleted. Returning to the phone setup.”
is heard and “Deleted” is displayed.
When using the knob:
“Deleted. Returning to the phone setup.”
is heard and “Deleted” is displayed.The system may not function in the follow-
ing cases:
If no phone has been registered.
If the system does not recognize the
voice command.The security menu includes the following:
Set PIN (Personal Identification Num-
ber)
The PIN can be set or changed.
Phone book lock
The phone book can be locked.
When the phone book is locked, the fol-
lowing functions cannot be used:
Dial by name
Redial
Callback
Speed Dial
PhoneBook
Phone book unlock
The locked phone book can be unlocked.
—Security

’07Camry_U (L/O 0608)
227
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
To enter the security menu
1. Push the off−hook switch to turn the
hands−free system on.
2. Follow voice guidance instructions, or
turn the “AUDIO CTRL” knob until
“Setup” is displayed and push the
knob.
“Setup. Please push the talk switch and
say security, or phone setup.” is heard.
3. Follow voice guidance instructions, or
turn the “AUDIO CTRL” knob until
“Security” is displayed and push the
knob.
“Security. Push the talk switch and say
set PIN, phone book lock, or phone book
unlock.” is heard.To set a PIN
Push the talk switch and say “Set PIN”,
or turn the “AUDIO CTRL” knob until “Set
PIN” is displayed and push the knob.
“There is no PIN number set. Please reg-
ister a PIN number. Please push the talk
switch and say a four−digit PIN number.”
is heard.When using a voice command:
1. Push the talk switch and say “XXX
(new PIN number)”.
2. Follow voice guidance instructions, or
turn the “AUDIO CTRL” knob until
“Confirm” is displayed and push the
knob.
“The PIN number has been set. Returning
to the security.” is heard and “Completed”
is displayed.
When using the knob:
1. Turn the “AUDIO CTRL” knob to select
a number. Push the “AUDIO CTRL”
knob to set.
2. Repeat the above procedure until the
entire four−digit number is set.
3. When the PIN is set, push the “AUDIO
CTRL” knob.
4. Follow voice guidance instructions, or
turn the “AUDIO CTRL” knob until
“Confirm” is displayed and push the
knob.
“The PIN number has been set. Returning
to the security.” is heard and “Completed”
is displayed.