’07Camry hybrid_U (L/O 0610)
i
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
Foreword
Welcome to the growing group of value−conscious people who drive Toyotas. We are proud of the advanced engineering and
quality construction of each vehicle we build.
This Owner ’s Manual explains the operation of your new Toyota. Please read it thoroughly and have all the occupants
follow the instructions carefully. Doing so will help you enjoy many years of safe and trouble free motoring. For
important information about this manual and your Toyota, read the following pages carefully.
When it comes to service, remember that your Toyota dealer knows your vehicle very well and is interested in your complete
satisfaction. Your Toyota dealer will provide quality maintenance and any other assistance you may require.
If there is not a Toyota dealer near you, please call the following number:
U.S. OWNERS:
When traveling in the U.S. mainland or Canada: Toyota Customer Experience Center Toll free:1 800 331 4331
Hawaii:
Servco Automotive Customer Services Toll free:1 888 272 5515
CANADIAN OWNERS:
When traveling in Canada or the U.S. mainland: Toyota Canada Customer Interaction Centre Toll free:1 888 TOYOTA 8 or 1 888 869 6828
Please leave this Owner ’s Manual in this vehicle at the time of resale. The next owner will need this information also.
All information and specifications in this manual are current at the time of printing. However, because of Toyota’s policy of
continual product improvement, we reserve the right to make changes at any time without notice.
Please note that this manual applies to all models and explains all equipment, including options. Therefore, you may
find some explanations for equipment not installed on your vehicle.
Please access our websites for further information.
The U.S. mainland www.toyota.com
Hawaiiwww.toyotahawaii.com
Canadawww.toyota.ca
©2006 TOYOTA MOTOR CORPORATION
All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of Toyo ta
Motor Corporation.
’07Camry hybrid_U (L/O 0610)
28
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
To lock or unlock all the doors, push
the switches slowly and securely.
To lock: Push the lock switch. All the
doors are locked simultaneously. At this
time one beep will sound and turn signal
lights flash once.
Check to see that the doors are securely
locked.
If any of the doors is not securely closed,
or if the key is left in the vehicle, locking
cannot be performed by the lock switch
and a beep will sound continuously for 10
seconds.
To stop the beep, take out the key from
the vehicle or push the unlock switch.
The answerback function (the turn signal
flash and the beep) can be disabled. For
details, contact your Toyota dealer.
To unlock: Push the unlock switch once to
unlock the driver ’s door alone. Pushing
the switch twice within 3 seconds unlocks
all the doors simultaneously. Each time
the unlock switch is pushed, two beeps
will sound and turn signal lights flash
twice.
This double switch operation to unlock all
doors can be changed to a single switch
operation. For details, contact your Toyota
dealer.If the “POWER” switch is set at ACC or
ON, the vehicle cannot be unlocked via
the unlock switch.
You have 60 seconds to open a door after
using the wireless remote unlock feature.
If a door is not opened by then, all the
doors will be automatically locked again.
If the wireless remote control is used to
lock the doors near the window or door
handle, there is a possibility that the door
may not unlocked by entry function of
smart key system. Under these circum-
stances, use the wireless remote control
function to unlock the doors.
The automatic locking time can also be
set to 30 seconds. For details, contact
your Toyota dealer.
If the lock or unlock switch is kept
pressed in, the locking or unlocking opera-
tion is not repeated. Release the switch
and then push again.
When you unlock doors using the wireless
remote control, the illuminated entry func-
tion will be activated. (For further informa-
tion, see “Illuminated entry system” on
page 127 in Section 1
−5.)
To open the trunk lid, push the trunk
opener switch of the electronic key for
1 second. A long beep will sound.
If the “POWER” switch is set at ACC or
ON, the trunk lid cannot be opened by the
trunk opener switch.
—Opening trunk lid
’07Camry hybrid_U (L/O 0610)
36
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
To reactivate the smart key system, per-
form any of the following:
(a) Press the lock button on the front out-side door handle or trunk open button
while carrying the electronic key.
(b) Perform a wireless remote control op- eration.
(c) Insert and turn the mechanical key in the keyhole of the driver’s door. If the electronic key receives strong elec-
tromagnetic waves over a period of time,
the battery can be drastically run down.
You should always keep the following
electrical appliances at least 1 m (3 ft.)
away from the electronic key.
TV
Personal computer
Cellular phone or cordless phone re-
charger unit
Electric light stand
Fluorescent desk light For vehicles sold in U.S.A.
FCC ID: NI4TMLF 2
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, includ-
ing interference that may cause unde-
sired operation.
CAUTION
Changes or modifications not ex-
pressly approved by the party respon-
sible for compliance could void the
user’s authority to operate the equip-
ment.
’07Camry hybrid_U (L/O 0610)
121
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
Automatic light cut off system
Position 1 or “AUTO” position with the
tail lights on—
The lights automatically turn off when the
driver ’s door is opened after the “POWER”
switch is turned off.
Position 2 or “AUTO” position with the
headlights on—
The lights automatically turn off after 30
seconds when any of the doors or trunk
lid is opened and closed after the
“POWER” switch is turned off.
The lights can be turned off immediately
by pushing the lock switch on the elec-
tronic key with all the doors locked and
the trunk lid closed.
The time period before the lights turn off
can be changed. For details, ask your
Toyota dealer.
If any of the doors or trunk lid is left
open, the lights automatically turn off after
20 minutes.
To turn on the lights again, set the
“POWER” switch at ON or actuate the
headlight switch. If you are going to park
for over one week, make sure the knob is
in the “DRL OFF” position.NOTICE
To prevent the 12 volt battery from
being discharged, do not leave the
lights on for a long period when the
hybrid system is turned off.
Daytime Running Light (DRL) system
The Daytime Running Light (DRL) system
can make it easier for others to see the
front of your vehicle during the day. The
DRL system can be helpful in many differ-
ent driving conditions, but they can be
especially helpful in the short periods after
dawn and before sunset.
The DRL system will make your headlights
come on at a reduced brightness when:
The “POWER” switch is set at ON with
the hybrid system turned on.
The light switch is in the “AUTO” posi-
tion with the headlights off or position
1.
The parking brake is released.
To turn on the other exterior lights and
instrument panel lights, twist the knob to
position 1.
Twist the knob to position 2 to turn the
headlights to full intensity for night driving.
To turn off the DRL system, twist the knob
to the position 3 (“DRL OFF”) or turn the
“POWER” switch off.
The daytime running light system can be
disabled. For details, contact your Toyota
dealer.
’07Camry hybrid_U (L/O 0610)
123
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
Manually twist the knob to the position 2
to turn on the headlights if they are need-
ed immediately when entering a dark tun-
nel, parking structure, etc.
When the tail lights/headlights are turned
on, the brightness of the instrument clus-
ter will be reduced slightly unless the in-
strument panel light control knob is turned
fully clockwise.
However, the brightness of the instrument
cluster will not be reduced in daytime
even when the tail lights/headlights are
turned on.
The automatic light control sensor is on
the top of the instrument panel.
Do not place anything on the instrument
panel, and/or do not affix anything on the
windshield to block this sensor.
If you feel that the automatic light control
comes into operation too early or too late,
have the sensor adjusted by your Toyota
dealer.Automatic light cut off system
Position 1 or position 3 with the tail
lights on—
The lights automatically turn off when the
driver ’s door is opened after the “POWER”
switch is turned off.
Position 2 or position 3 with the head-
lights on—
The lights automatically turn off after 30
seconds when any of the doors or trunk
lid is opened and closed after the
“POWER” switch is turned off.
The lights can be turned off immediately
by pushing the lock switch on the elec-
tronic key with all the doors locked and
the trunk lid closed.
The time period before the lights turn off
can be changed. For details, ask your
Toyota dealer.
If any of the doors or trunk lid is left
open, the lights automatically turn off after
20 minutes.
To turn on the lights again, set the
“POWER” switch at ON or actuate the
headlight switch. If you are going to park
for over one week, make sure the knob is
in the “OFF” position.
’07Camry hybrid_U (L/O 0610)
128
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
If all the doors are closed, when the
“POWER” switch is turned off, the lights
will come on and remain on for about 15
seconds.
This feature can be disabled and the dura-
tion of the lighting can be changed. For
details, ask your Toyota dealer.
To turn on the windshield wipers, move
the lever to the desired setting.
The “POWER” switch must be set at ON.Lever position
Operation
Position 1Intermittent operation
Position 2Low speed operation
Position 3High speed operation
Position 4Single sweep operation
Position 5Washer on
Rotating the band on the lever lets you
adjust the wiper time interval when the
wiper lever is in the intermittent position
(position 1). Twist the band upward to
increase the time between sweeps, and
downward to decrease it.
To spray washer fluid, pull the lever
toward you.
If the windshield wipers are off, they will
operate a couple of times after the washer
sprays.
For instructions on adding washer fluid,
see “Adding washer fluid” on page 373 in
Section 7 −3.
In freezing weather, warm the windshield
with the defroster before using the washer.
This will help prevent the washer fluid
from freezing on your windshield, which
can block your vision.
NOTICE
Do not operate the wipers if the wind-
shield is dry. It may scratch the
glass.
Windshield wipers and washer
’07Camry hybrid_U (L/O 0610)
132
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
The gauge indicates the approximate
quantity of fuel remaining in the tank
when the “POWER” switch is set at ON.
Nearly full—Needle at “F”
Nearly empty—Needle at “E”
It is a good idea to keep the tank over
1/4 full.
If the fuel level approaches “E” or the low
fuel level warning light comes on, fill the
fuel tank as soon as possible.
On inclines or curves, due to the move-
ment of fuel in the tank, the fuel gauge
needle may fluctuate or the low fuel level
warning light may come on earlier than
usual.If the fuel tank is completely empty, the
malfunction indicator lamp comes on. Fill
the fuel tank immediately.
The indicator lamp goes off after driving
several times. If the indicator lamp does
not go off, contact your Toyota dealer as
soon as possible.The gauge indicates the engine coolant
temperature when the “POWER” switch
is set at ON. The engine operating tem-
perature will vary with changes in
weather and engine load.
1. Red zone
2. Blue zone
If the needle moves into the red zone,
your engine is too hot. If your vehicle
overheats, stop your vehicle and allow the
engine to cool.
Fuel gauge Engine coolant temperature
gauge
’07Camry hybrid_U (L/O 0610)
139
2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)
3. Trip meter reset knob—Resets the twotrip meters to zero, and also change
the meter display.
To change the meter display, quickly
push and release the knob. The meter
display changes in the order from the
odometer to trip meter A to trip meter
B, then back to the odometer each
time you push.
To reset the trip meter A to zero, dis-
play the meter A reading, then push
and hold the knob until the meter is
set to zero. The same process can be
applied for resetting the trip meter B.