2007 SKODA OCTAVIA TOUR warning light

108SAFETYSwitching on airbag
Switch the ignition off.

Use the ignition key to turn the airbag
switch - arrow - into the „ON“ position. The
ignition key must be in the horizontal posi-
tion.

Check whether the airbag warning light
in the interior lighting (front) goes out when
the ignition is switched on.
After activating the airbag and then switch-
ing on the ignition, the airbag warning light
comes on for about 3 seconds.
Warning
The driver of the car is responsible
for ensuring that the airbag is deac-
tivated or activated.
„Airbag OFF“ warning light
(airbag deactivated)*The warning light is located in the front in-
terior lighting of the car.
Each time the ignition is switched on, the
warning light comes on in the dash panel
for a few seconds (self diagnosis).
The warning light comes on if the passen-
ger- side airbag or also the side airbag has
been deactivated.
If the warning light in the instrument panel
flashes, there is a fault in the airbag sys-
tem. Contact a Škoda Dealer immediately
to have this rectified Warning
If the warning light flashes:


There is a risk of the passenger-
side airbag being deployed in the
event of an accident. For this reason,
do not install a child seat on the front
passenger seat.

If the front passenger seat is oc-
cupied, there is a risk of the airbag
being deployed unexpectedly and
also causing possible injuries to the
occupant of the front passenger seat.

111
SAFETY

Only light items of clothing should
be hung up on the clothes hooks in
the car. No heavy or sharp-edged
objects should be stowed in the
pockets of the items of clothing.

Avoid any excessive force acting
on the side panels of the seats, such
as a sudden knock, or pressing with
your foot etc., otherwise the system
may be damaged. In this case, the
side airbags would not deploy!

On no account may seat or protec-
tive covers be fitted over the driver
or front passenger seats fitted with
side airbags. As the airbag inflates
out of the backrest of the seat, the
protective function offered by the
side airbags would be restricted if
seat protective covers were used.

If the original seat cover or the stit-
ching in the module area of the side
airbag is damaged, the seat cover in
question should be replaced imme-
diately by a Škoda Dealer.

The protection offered by the air-
bag system is sufficient only for one
accident. If the airbag has been de-
ployed, the system should be rene-
wed.

If the occupants lean forward or
adopt an incorrect seated position
when driving, they are exposing
themselves to an increased risk of an
injury in the event of an accident.

A child seat in which the child
faces with its back in the direction of
travel, may only be used in the front
passenger seat if the front passen-
ger airbag (in certain countries also
on child seats in which the child
faces the direction of travel) has
been deactivated - refer to page 107.
Otherwise, there is a risk of the child
suffering severe or even fatal injuries
if the airbag is deployed. In certain
countries, legal requirements neces-
sitate deactivating the side airbag. If
a child is nevertheless seated on the
front passenger seat, observe the le-
gal requirements for the use of child
seats.
Safety of childrenAccident statistics reveal that children
who sit at the rear are generally better
protected than when seated on the front
passenger seat. Children younger than
12 years should normally travel on the
rear seat of the car
1). They should be
protected by a child restraint system or
by the standard car seat belts, depend-
ing on age, body size and weight. For
safety reasons, the child restraint sys-
tem should be installed behind the front
passenger seat.
Warning

All vehicle occupants, in particu-
lar children, must fasten their seat
belt when the car is moving.


Never allow your child to stand in
the car or to kneel on the seats when
the car is moving. If an accident oc-
curs, your child will be thrown through
the car and may suffer fatal injuries.
1)Pay attention to any varying legal requirements.

117
DRIVING TIPS
The first 1500 kilometres (1000 miles) - and afterRunning inDuring the first few operating hours the in-
ternal friction of the engine is higher than
later on when all the moving parts have
bedded down. How well this running-in
process is done depends to a considerable
extent on the way the vehicle is driven dur-
ing the first 1500 km (1000 miles).
Up to 1000 km (600 miles)
the following general rules apply:

Do not use full throttle

Do not drive faster than 3/4 of top speed

Avoid high engine speeds

Avoid towing a trailer, if possible
Warning

New tyres should also be „run in“
because they do not have maximum
adhesion at the start. This should be
taken into account by driving care-
fully during the first 500 km (300 mi-
les).

New brake pads have to „bed
down“ and do not therefore have
their ideal friction force during the
first 200 km (120 miles) or so. The
slightly reduced braking power can
be compensated for by applying
greater pressure on the brake pedal.
This also applies subsequently after
replacing the brake pads.
From 1000 - 1500 km (600 - 1000 miles)
It is possible to gradually increase up to the
maximum speed of the gear engaged or to
the maximum permissible engine speed,
respectively.
During and after the running-in pe-
riod:
Do not overrev the engine when cold -
either in Neutral when driving. All the
speeds and revs stated only apply when the
engine is properly warm .
Do not drive at unnecessarily high
engine speeds - changing up early
helps to save fuel, reduces noise and pro- tects the environment - see also page 118.

Do not let the engine labour - change down
when engine no longer runs smoothly.After the running-in periodOn cars fitted with a rev counter the maxi-
mum permissible engine speed is marked
by the start of the red range on the scale of
the rev counter. The needle of the rev coun-
ter must not move into this range.

121
DRIVING TIPS
The full braking effect may also be delayed
when the car has been driven for some time
on heavily salted roads without using the
brakes, because the layer of salt on the
discs and pads has to be removed first.Warning
If a front spoiler, full-size wheel trims
etc., are retrofitted, it is necessary to
ensure that the flow of air to the front
brakes is not restricted - otherwise
the brakes may overheat.
Brake booster
The braking force boosts the pressure,
which you generate with the brake pedal.
The necessary pressure is only generated
when the engine is running. Warning
The brake booster only operates
when the engine is running.
Never switch off the engine before
the vehicle is stationary.
In the case that the brake booster is
not operating - e.g. because the vehi-
cle has to be towed or because there
is damage to the brake booster - the
brake pedal has to be depressed with
a significantly greater force, in order
to balance out the missing brake
boosting effect.Because if you do not stop as nor-
mal, this can cause an accident and
severe injuries.
Brake Assist*
The Brake Assist boosts the brake servo
effect during a brake application in a haz-
ardous situation and is able in this way to
assist the rapid build-up of brake pressure.
In emergency situations the majority of car
drivers do apply the brakes in time, but not
with the brake pedal force which is neces-
sary for achieving maximum deceleration.
Valuable braking distance is lost as a result!The Brake Assist is activated as soon as the
brake pedal is depressed very rapidly. A hig-
her brake servo assistance than is usual in
normal brake applications, is then available.
Consequently, it is possible to build up
within a very short time the brake pressure
which is required for achieving maximum
deceleration with only a correspondingly
slight counterforce on the brake pedal.Depress the brake pedal further for achiev-
ing the shortest possible braking distance. Do
not reduce the foot pressure on the pedal!The Brake Assist is able in this way to help
you in critical situations by building up the
brake pressure more rapidly and shorten-
ing the stopping distance. The advantages
offered by the ABS are fully exploited by the
Brake Assist. As soon as the brake pedal is
released, the Brake Assist function is swit-
ched off then automatically and the usual
service brake function is again available.
Warning

The Brake Assist is also not in a
position to overcome the physical
limits which apply to the braking dis-
tance.

This is something you should re-
member particularly when driving on
smooth or wet road surfaces.

Adapt your style of driving always
to the road condition and the traffic
situation. The increased safety which
the Brake Assist offers you must not
lead you to take any safety risk!

126DRIVING TIPSDriving instructions
To obtain the best possible handling of ve-
hicle and trailer, please note the following
points:

Try to avoid driving with an unladen ve-
hicle and a loaded trailer. If this cannot be
avoided, only drive slowly to allow for the
unfavourable weight distribution.

As the driving stability of vehicle and trai-
ler decreases when the speed increases,
do not drive at the maximum permissible
top speed in unfavourable road, weather or
wind conditions - particularly when going
downhill.
You should in any case immediately reduce
your speed as soon as you detect even the
slightest swaying of the trailer. On no ac-
count attempt to eliminate the swaying by
accelerating!

For safety reasons, you should not drive
faster than 80 km/h (50 mph). This also
applies in countries where higher speeds
are permitted.

Apply the brakes in good time! If the
trailer is fitted with an overrun brake, apply
the brakes gently at first, then increase the
pressure. This avoids any braking shocks
caused by the wheels of the trailer block-
ing. Shift down gears in good time before
driving downhill so that the engine can act
as a brake.

If it is necessary to drive a long uphill
section in a low gear with a very high en-
gine speed and at unusually high ambient
temperatures, keep a check on the cool-
ant gauge. If the needle of the gauge moves
into the upper range of the scale, reduce
the speed of your car immediately. If the
temperature and brake fluid level warning
light flash, however, stop and allow engine
to cool down by letting it idle for a few min-
utes. Pay attention to the further informa-
tion on p. 46.

The coolant temperature can be reduced
by switching on the heater.

The cooling effect of the radiator fan
cannot be increased by changing down,
because the speed of the fan is not depend-
ent on the engine speed. You should there-
fore not change down even when towing a
trailer as long as the engine can cope with-
out the vehicle speed dropping too much.
General notes

It is advisable to have the vehicle ser-
viced between the inspection intervals
if it is used frequently for towing a trailer.

The trailer and drawbar load figures on
the data plate of the towing bracket are for
test certification only. The correct figures for
the vehicle, which may be lower than the
above figures, are given in the vehicle do-
cuments.

130GENERAL MAINTENANCEWashing the carThe best protection for your car against
harmful environmental influences is fre-
quent washing and polishing.
How often your car requires to be treated
depends among other factors on how fre-
quently you use the car, where you park it
(garage, in the open, below trees etc.), the
time of year, the weather conditions and
other environmental influences.
The longer bird droppings, insect residues,
tree resin, road and industrial dust, tar
stains, soot particles, road salt and other
aggressive deposits remain on the paint-
work of your car, the more extreme will be
their destructive effect. High temperatures
caused by strong sun’s rays, intensify the
caustic effect. It may therefore be neces-
sary to wash the car once a week, but once
a month may also be sufficient with appro-
priate waxing.
It is essential to also thoroughly wash the
underside of the car after the end of the
winter period.Automatic car washes
The paintwork of your car is sufficiently re-
sistant to enable the car to be washed nor-
mally in automatic car washing plants with-
out any problems. The effect on the paint-
work, though, also depends greatly on the
design of the car wash, the filtering of the
washing water, the type of wash and care
products used etc. If the paintwork appears
mat after a car wash or even has scratches,
you should contact the operator of the plant.
If necessary, change the car wash you use.
Notes


Before washing your car in an automatic
car wash, there are no special precautions
necessary other than the usual measures
(closing windows and sliding roof, folding
down roof aerial etc.).
Warning
Do not tighten roof aerial in the lower
position

It is best to contact the operator of the
car wash if your car has any particular spe-
cial fittings - e.g. spoiler, roof rack, mobile
phone aerial etc.


After washing your car in an automatic car
wash with wax preservative, wipe the lips of
the windscreen wiper blades clean and also
clean the windscreen (also the rear window
on models fitted with rear window wiper).
Washing your car by hand
As a protection for the environment,
your car should only be washed at
washbays provided for this purpose.
Local regulations may in fact forbidwashing cars in certain areas outside ofsuch facilities.
First of all soften the dirt with plenty of wa-
ter and rinse off as well as possible.
Then, clean the car with a soft sponge,
washing glove or brush starting on the roof
and working down, applying only slight
pressure. Use a car wash shampoo only
for particularly stubborn dirt.
Thoroughly wash out the sponge or glove
at short intervals.
Clean wheels and door sills etc. last. Use
a second sponge if possible for such ar-
eas.
After washing the car, rinse it thoroughly
with water and finally chamois dry.

131
GENERAL MAINTENANCE
Notes

The car should not be standing in bright
sunshine when it is washed.

If a hose is used to spray down the car,
do not aim the jet of water directly at the
door locks and body panel gaps - otherwise
they may freeze up in winter.Washing the car with high-pressure
cleaners
It is essential to follow the instructions
for using high-pressure cleaners - particu-
larly as regards the pressure and spraying
distance.

Do not use round spray nozzles or so-
called „dirt shifters“!

The temperature of the water should not
be more than 60 °C.
WarningTyres must never be cleaned with
round jet nozzles. Damage may occur
even if only sprayed for a short time
or from a relatively large distance.WaxingGood wax treatment protects the paintwork
of your car from the environmental influ-
ences listed on the previous page under
„Washing the car“ and also from slight me-
chanical damage. The vehicle must be treated with a high-
quality hard wax polish at the latest, when
no more drops form on the clean paintwork.
Do not apply a new film of wax protection
until the body surface is dry. Even if a wax
preserver is used regularly, it is recom-
mended to protect the paintwork at least
twice a year with hard wax.
Warning
Never treat the windscreen or win-
dows with wax.
PolishingPolishing is only necessary if the paintwork
has become unattractive and it is no longer
possible to achieve a gloss with a wax pre-
server. If the polish used does not contain
any preserving elements, the paintwork
should then be treated with wax preserver.
Note
Mat painted parts and plastic parts must
not be treated with polish or hard wax.
We recommend using the products from
the Škoda range.
Do not polish the paintwork of the vehicle
in a dusty environment, otherwise the
paintwork can be scratched.
Paint damageMinor paint damage such as scratches,
rubs or stone chips, should be treated im-
mediately with paint (Škoda touch-up pen
or spray can) before rust can form.
This repair work can also of course be car-
ried out by a Škoda Dealer. The colour
code is stated on the car data sticker, see
page 181.WindowsUse only a plastic scraper to remove snow
and ice from windows and mirrors. The
scraper should not be moved back and for-
ward, but only pushed in one direction in
order to avoid scratches caused by dirt.
Residues of rubber, oil, grease, wax or sili-
cone sealant can be removed with a wind-
screen cleaner or special silicone remover.
The windows should also be cleaned at
regular intervals from the inside.
Do not use the same chamois leather for
drying the windows and for the paintwork
because residues of wax preservers will
cause smears on the surface of the win-
dows.
Never remove snow or ice from the win-
dows with warm or hot water - risk of
formation of cracks in the glass!

132GENERAL MAINTENANCEDo not affix any stickers from the inside
over the heating circuit to avoid damaging
the heating circuit of the rear window
heater .
Models fitted with all-wheel drive:
The adhesive sticker for identifying 4x4 mo-
dels on the rear window must only be re-
moved by a Škoda Dealer using a special
technology otherwise the rear window
heater might be damaged.Door, window , bonnet/tailgate sealsThe rubber seals remain supple and last
longer if they are treated from time to time
with a light film of a rubber care product.
They also will not then freeze up in winter!Plastic parts and synthetic leatherExterior plastic parts are cleaned by wash-
ing in a normal way and interior parts by
using a damp cloth. Should this not be ad-
equate, plastic parts and synthetic leather
must only be treated with special solvent-
free plastic cleaning and care products.
We recommend using a cleaning product
from Škoda original accessories offered by
your Škoda dealer.
Note
Solvent-free cleaners attack the material
and can damage it.
Upholstery cloth and cloth trimUpholstery cloth and cloth trim on the doors,
rear shelf, luggage compartment cover, head-
lining etc. are treated with special cleaning
products or with dry foam and a soft brush.Cleaning seat beltsKeep belts clean! If the belt webbing is
very dirty, this may prevent the inertia reel
belt from retracting properly.
Wash dirty belt webbing only with a mild
soap solution without taking the seat belts
out of the car.
Note
Dry inertia reel belts completely before re-
tracting.
Warning
Do not have the belts dry-cleaned be-
cause dry-cleaning products damage
the webbing material. Ensure that the
belts do not come into contact with
corrosive fluids.
Chrome partsFirst clean the chrome parts with a damp
cloth and then polish them with a soft, dry
cloth.
If it does not prove to be adequate, use a
chrome care product from Škoda original
accessories.
NoteDo not polish the chrome parts in a dusty en-
vironment, otherwise they can be scratched.Natural leatherLeather should be treated from time to time
in accordance with the instructions below,
depending on the amount of use. It is im-
portant to ensure that the leather must
not be treated on any account with sol-
vents, floor wax, shoe cream, stain re-
mover or similar products.
For normal cleaning of leather-trim steer-
ing wheels, leather seat covers etc., slightly
moisten a cotton or woollen cloth with wa-
ter and clean the soiled surfaces of the
leather. Severe soiling can be cleaned with
a mild soap solution (2 soup-spoonfuls of
neutral soap to 1 litre of water). It is very
important to ensure that the leather is not
moistened through at any point and that
no water is able to trickle through the stitch-
ing. Wipe the leather dry finally with a soft,
dry cloth.