2007 SKODA OCTAVIA display

Instruments and Indicator/Warning Lights17
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
you must first erase the memory at this moment in time by pressing the button
⇒
page 15, fig. 6 .
The maximum distance indicated in both switch positions is 9999 km. The indicator
is set back to null if this period is exceeded.
Average speed
The average speed since the memory was last erased is shown in the display in
km/hour ⇒page 14. If you wish to determine the average speed over a certain
period of time you must first erase the memory at the start of the new measure-
ment using the button ⇒page 15, fig. 6 .
A zero appears in the display for the first 100 m you drive after erasing the memory.
The indicated value will be updated every 5 seconds while you are driving.
Driving time
The driving time which has elapsed since the memory was last erased, appears in
the display ⇒page 14. If you wish to calculate th e driving time from a particular
time of day you must first erase the memory at this moment in time by pressing the
button ⇒page 15, fig. 6 .
The maximum distance indicated in both memories is 99 hours and 59 minutes.
The indicator is set back to nu ll if this period is exceeded.
Warning against excessive speeds*
Warning against excessive speeds 1)
This function enables you to set a speed limit, e.g. if you drive in town. A text in the
display is intended to draw your attention to the fact that you have exceeded the set
speed limit.
You can set the desired speed limit as follows:
•Select the menu Speed warning --- km/h (warning at --- km/h) .
•You can drive at the desired speed, e.g. 50 km/h
AB
AB
AB
1)Valid for vehicles with information display.
Fig. 8 Speed setting
Fig. 9 Multi-functional
indicator: Control
elements
NKO A5 20 MR08.book Page 17 Wednesday, April 11, 2007 2:54 PM

Instruments and Indicator/Warning Lights
18
•Press the button ⇒page 17, fig. 9 - Speed warning 50 km/h (warning at
50 km/h) is shown on the display.
If you now exceed the set speed limit, Speed 50 km/h exceeded (speed 50 km/h
exceeded) will be shown on the di splay. This display will be shown until you have
reduced the speed to the set speed limit.
A peep sounds as an additional warning signal.
The set speed limit remains stored in the memory, also when the ignition is
switched off and on; it can only be erased by pressing the button for more than
1 second.
Information display*
Introduction
The information display provides you with information in a convenient way
concerning the current operating state of your vehicle . The information system
also provides you with data (depending on the equipment installed in the vehicle)
relating to the radio, mobile phone, multi-functional indicator, navigation system
and automatic gearbox.
Certain functions and operating conditio ns are always being checked on the
vehicle when the ignition is switched on and also while driving. Functional faults, if required repair work and other information are indicated by red
symbols
⇒page 21 and yellow symbols ⇒ page 22.
Lighting up of these symbols is combin ed with an acoustic warning signal.
Information and texts giving warnings are also shown in the display ⇒page 24.
The display of text is possible in the following languages: Czech, English, German, French, Italian, Spanish, Portuguese.
You can select the desired la nguage in the setting menu ⇒page 22.
The following information can be shown in the display (depending on the equip-
ment installed on the vehicle):
AB
AB
Fig. 10 Instrument
cluster: Information
display
Main menu⇒ page 19
Door, luggage compartment door and bonnet ajar
warning⇒page 20
Service Interval Display⇒page 12
Selector lever positions of the 6-speed automatic
gearbox⇒page 127
Selector lever positions of the automatic DSG⇒page 133
NKO A5 20 MR08.book Page 18 Wednesday, April 11, 2007 2:54 PM

Instruments and Indicator/Warning Lights19
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Main menu
– You can activate the MAIN MENU by pressing the rocker switch
⇒ fig. 12 for more than 1 second.
– You can select the menu through the rocker switch . When the pushbutton is briefly pressed, the information you have selected is
displayed.
You can select the following information (depending on the equipment installed on
the vehicle):
„MFD (Onboard computer) ⇒ page 14
„The outside temperature
„Current consumption
„Average fuel consumption
„Range
„Distance driven
„Average speed
„Driving time
„Warning against excessive speeds
„Audio ⇒ page 20
„Navigation ⇒ page 20
„Te l e p h o n e ⇒ page 142
„Vehicle status ⇒ page 21
„Setup ⇒ page 22
„Time
„Winter tyres
„Language
„Units
„Lights & Vision&
„Aux. Heating (auxiliary heating)
„Back
„Display off
After selecting the menu Display off the display is switched off. Press rocker switch
for at least 1 second to switch the display on again.
The menu Audio is only displayed when th e Radio* is switched on.
The menu Navigation is only displayed when the Navigation* is switched on.
Aux. Heating (auxiliary heating) is only then displayed, if the vehicle is fitted with
auxiliary heating*.
Fig. 11 Information
display: Menu
Fig. 12 Information
display: Control
elements
AA
AA
AB
AA
NKO A5 20 MR08.book Page 19 Wednesday, April 11, 2007 2:54 PM

Instruments and Indicator/Warning Lights
20
Note
If you do not activate the information disp lay at that moment, the menu shifts to
one level higher every 10 seconds.
Door, luggage compartment door and bonnet ajar warning
The door, luggage compartment door and bonnet ajar warning lights up when at
least one of the three items door, luggage compartment or bonnet are not closed
when the ignition is turned on. The symbol indicates which door is still open or
whether the luggage compartment door or bonnet is not closed ⇒fig. 13 .
The symbol goes out as soon as the doors, luggage compartment door and bonnet
are completely closed.
As an additional warning signal, a 3 time peep sounds if the car is driven at a speed
of more than 6km/hour and if the door, engine or luggage compartment door is
open.
Audio
These displays appear in addition to the normal information in the radio display.
Operation of the radio system is described in separate operating instructions to be
found in the on-board literature.
Navigation system*
The controls for the navigation system, radi o, CD player are located in the centre
console on both sides of the monitor screen. Navigation data is also shown in the
information display of the instrument cluster.
Information and warning texts are displayed preferentially when the navigation
system is switched on.
Operation of the navigation system is described in separate operating instructions
to be found in the on-board literature.
Fig. 13 Information
display: Door warning
Fig. 14 Information
display: Radio display
NKO A5 20 MR08.book Page 20 Wednesday, April 11, 2007 2:54 PM

Instruments and Indicator/Warning Lights21
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Auto Check Control*
Car state
The Auto Check Control carries out a check of certain functions and vehicle compo-
nents. The check is performed constantly when the ignition is switched on, both
when the vehicle is stationary, as well as when driving.
Operational faults, urgent repairs, service work or other information appear in the
display of the instrument cluster. The disp lays are shown with a red or yellow light
symbol depending on the priority of the message.
The red symbols indicate danger (priority 1) while the yellow symbols indicate a
warning (priortity 2). Information for the driver may also appear in addition to the
symbols ⇒page 24.
There is at least one error message to be read when the term Vehicle status is
flashing in the main menu. After selecting this menu the first of the error messages
is displayed. If there are several error messages, they are shown on the display
under the message e.g. 01/03 ⇒ fig. 15 . This display indicates that the first of a total
of three error messages should be displa yed. The respective symbols light up one
after the other in an interval of 5 seconds. Investigate the displayed faults as soon
as possible.
As long as the operational faults are not rectified, the symbols are always indicated
again. After the first display, the symbols are indicated without information for the
driver. If a fault occurs, a warning signal will also sound in addition to the symbol and text
in the display:
•Priority 1 - three warning signals
•Priority 2 - one warning signal
Red symbols
A red symbol signals danger.
Proceed as follows if a red symbol is displayed:
– Stop the vehicle.
– Switch the engine off.
– Investigate the function indicated.
– Obtain professional assistance.
Meaning of the red symbols:
Fig. 15 Information
display: Display of opera-
tional fault
Coolant level too low/coolant tempera-
ture too high⇒
page 28
Engine oil pressure too low⇒page 29
Fig. 16 Information
display: Oil pressure is
low
NKO A5 20 MR08.book Page 21 Wednesday, April 11, 2007 2:54 PM

Instruments and Indicator/Warning Lights
22
Three successive warning signals will sound if a red symbol appears.
If several operational faults of priority 1 exist, the symbols appear one after the
other and are each illuminated for about 5 seconds.
Yellow symbols
A yellow symbol signals a warning.
Check the relevant function as soon as possible.
The meaning of the yellow symbols:
One warning signal will sound if a yellow symbol appears.
If several operational faults of priority 2 exist, the symbols appear one after the
other and are each illuminated for about 5 seconds.
Set-up
You can change certain settings by means of the information display. The current
setting is shown on the information display in the respective menu at the top below
the line ⇒fig. 18 .
You can select the following information (depending on the equipment installed on
the vehicle):
•Time
•Winter tyres
•Language
•Units
•Lights & Vision&
•Aux. Heating (auxiliary heating)
•Back
After selecting the menu Back you will reach one level higher in the menu.
Set hours
Here you can set the time, the time format (12 or 24 hour indicator) and the time
change summer/winter time.
Fuel level low⇒ page 29
Check engine oil level,
engine oil sensor faulty⇒page 30
Brake pad worn⇒page 29
Washer fluid level low⇒page 29
Fig. 17 Information
display: Fuel level low
Fig. 18 Setting the clock
NKO A5 20 MR08.book Page 22 Wednesday, April 11, 2007 2:54 PM

Instruments and Indicator/Warning Lights23
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Setting for winter tyre speed
Here you can set at which speed a warning
signal should sound. These functions are
used for e.g on winter tyres with the permissible maximum speed less than the
maximum speed of the vehicle ⇒page 225.
When exceeding the speed, the following is displayed on the information display*: Speed warning
Language setting
Here you can set in which language the warning and information texts should be
displayed. After selecting the language, e. g. English, the following is displayed on
the information display:
Language: english set
Setting units
Here you can set the units for temperat ure, consumption and distance driven.
Setting lights
Here you can switch on or off the function convenience turn signal ⇒page 56.
Furthermore you can set how long the li ght should stay on for the function
Coming/Leaving Home ⇒page 53.
After selecting the menu Fa cto r y se tt ing the factory setting is established again.
Convenience setting*
You can set the following functions (depending on the equipment installed on the
vehicle):
Door openHere you can switch on or off the functions for open-
ing a single door and automatic closing ⇒page 37.
ATA c onfir mHere you can set if a signal tone should sound addi-
tionally when activating or deactivating the anti-theft
alarm system ⇒page 43.
Conv. modeHere you can set the convenience mode only for the
driver window or for all the windows ⇒page 47.
Mirror adjust.Here you can switch on or off the function for mirror
adjustment on the front pa ssenger side when engag-
ing the reverse gear ⇒page 65.
Mirror adjust.Here you can switch on or off the function for left and
right exterior mirror setting simultaneously
⇒page 65.
Rain-closing
On vehicles with rain sensor you can switch on or off
the function for automatic closing of the sliding/tilting
roof in case of rain. If it is not raining and the function
is set, the windows including the sliding/tilting roof
are closed automatically after approx. 12 hours.
Fa ct or y se t tin g
After selecting this menu the convenience setting is
reset to factory setting. The following is displayed in
the information display:
Factory setting for convenience is set
.
NKO A5 20 MR08.book Page 23 Wednesday, April 11, 2007 2:54 PM

Instruments and Indicator/Warning Lights
26
Main beam 
The indicator light  comes on when the main beam is selected or also when the
headlight flasher is operated.
Further information about the main beam ⇒page 56.
Low beam 
The indicator light  comes on when low beam is selected ⇒page 51.
Rear fog light 
The warning light  comes on when the rear fog lights are operating ⇒ page 53.
Electronic immobiliser
Data is compared between the ignition key and the control unit when switching on
the ignition. The indicator light  will light up for a few seconds when ignition key
authorisation is confirmed.
The warning light will start flashing conti nuously if a non-authorised ignition key
(for example the wrong ignition key) has been used. The engine cannot be started
⇒ page 36.
It is only possible to start the engine of the vehicle with a Genuine Škoda key with
the matching code.
The following text will be displayed in the information display*:
Immobilizer active
Diesel particle filter*  (diesel engine)
If the warning light  comes on, this means that soot has accumulated in the diesel
particle filter because of the frequent short distances. In order to clean the diesel particle filter,
the vehicle should be driven at an even
speed of at least 60 km/h at engine speeds of 1 800 - 2 500 rpm for at least 15
minutes or until the warning light goes ou t with the 4th or 5th gear engaged (auto-
matic gearbox: position S) when the traffi c situation permits it. This increases the
exhaust temperature and the soot deposited in the diesel particle filter is burnt.
Always pay attention to the valid speed limits ⇒.
The warning light
 goes out after the successful cl eaning of the diesel particle
filter.
If the filter is not properly cleaned, the warning light
 does not go out and the
warning light  begins to flash. Engine fault Workshop! is shown in the informa-
tion display*. Afterwards the engine cont rol unit shifts the engine into the emer-
gency mode, which only has a reduced powe r output. After switching the ignition
off and on again the warning light
 comes on.
Have the vehicle inspected without delay by your specialist garage.
WARNING
•If you do not pay attention to the wa rning light coming on and the corre-
sponding descriptions and warning notes, this may result in injuries or
major vehicle damage.
•Always adjust your speed to suit weather, road, region and traffic condi-
tions. The route indicated by the warn ing light must not tempt you to disre-
gard the national regulations for road traffic.
Caution
As long as the warning light  lights up, one must take into account an increased
fuel consumption and in certain circumst ances a power reduction of the engine.
Note
Further information about diesel particle filter ⇒page 188, “Diesel particle filter*
(diesel engine)”.
NKO A5 20 MR08.book Page 26 Wednesday, April 11, 2007 2:54 PM