2007 Seat Leon 5D ECO mode

Navigation35
WARNING
•
Please observe the laws of road traffic legislation when following the
recommendations made by your navigation system.
•
The destination guide is subject to constant changes despite the infor-
mation about one-way streets, pedestrian zones etc. stored on the naviga-
tion CD. Information on traffic lights, stop and right of way signs, parking
and stopping restrictions as well as lane constrictions is not included in
the navigation system. Traffic signs and legislation always have priority
over the recommendations made by the system.
•
Adjust your speed to suit road traffi c conditions and also weather and
visibility conditions. Do not follow the instructions of the navigation
system exclusively.
The navigation CDInserting the navigation CD
– Press the button ⇒page 3, fig. 1 to eject any CD in the
CD slot.
– Remove the CD and insert the navigation CD with the written side facing up.
– Push the CD into the slot until the radio navigation system pulls it in. The program stored on the navigation CD is loaded. Do not
remove the navigation CD before the loading process is finished.After the destination guide has begun, the navigation CD may be ejected to
listen to, for example, an audio CD ⇒page 56, “The destination guide
without the navigation CD”.
WARNING
Note also, the instructions and wa rning messages of the CD mode
⇒ page 20, “Important information on operating the CD player”.
Note
•
Note that a soiled or damaged navigation CD may negatively effect the
functions of the navigation system.
•
The extent to which small villages, streets and house numbers are
contained on the CD depends on the CD version.
•
You will need a new navigation CD for every country that you travel to.
•
The content of the CD is constantly being updated. You will receive infor-
mation on new updates at your next SEAT Official Service.
•
The navigation functions are limited if no navigation CD is inserted
⇒ page 56, “The destination guide without the navigation CD”.
General notesYou can continue to listen to the radio or CD whilst you are being guided to
your destination. Further informat ion can be found in the chapter ⇒page 56,
“The destination guide without the navigation CD”.
When entering an address (town, street), only those letters or symbols which
make up a logical entry will be presented. A list of possible names will be
shown. Do not forget to enter the blank space in names made up of more than
one word, such as Milton Keynes.
The route will be recalculated if you leave or disregard the route that was orig-
inally calculated. This process takes only a few seconds.

A10
RNS MP3_ingles Seite 35 Mittwoch, 10. Mai 2006 7:52 19

Navigation51
Specific destinations may also sele cted from an itinerary by pushing Start
route ; intermediate destinations are omitted.
When reaching an intermediate destination, an audio indication is given. The
route calculation to the following destination begins automatically.
When the intermediate destination is reached, it is possible to interrupt the
destination guide by pressing ; it may be resumed from the same
position by pressing the button.
Dynamic destination guide with TMC (Traffic Message Channel)
⇒ page 51
Starting the demonstration
To begin the demonstrat ion destination guide ⇒page 48, “Demonstration
mode”.
Note
•
If you hear a message indicating that you are driving on an unrecognized
road, you should continue to drive. Th e unit might have to orientate itself
using the next main road.
•
With the destination guide activated, stages may be added or established
destinations altered ( ⇒page 37, “Preparing the destination guide”). If a
destination is added, the equipment wi ll prepare an itinerary automatically
( ⇒ page 40, “Route planning”), even if the Route with stages function is
deactivated in route options ( ⇒page 42, “Route options”).
Dynamic destination guide with TMC (Traffic Message Channel)
During the dynamic destination guide, traffic reports emitted
by TMC stations are taken into account for route calculation.
In this way, problematic stretches are avoided.To activate or deactivate this fu nction, press the button ; this will
access the route options pressing ; the dynamic guide status
is selected using the option Dynamic Navigation.
It is also possible to press on the main navigation menu and activate
or deactivate the dynamic guide in the Route options ⇒ page 42, fig. 21 .
Once the dynamic destination guide function has been activated you will be
informed that the route is being recalcul ated due to traffic problems if any
have been registered.
Dynamic destination guide preconditions
In order to use the dynamic destination guide, a TMC station must always be
available ( TMC indicator on the lower right hand side of the screen). If the
station received does not offer the TMC service, it is possible to search for a
TMC station after beginning the destination guide. A selection may be made
from the TMC stations framework ⇒ page 12. Once a TMC station has been
found or selected, the destination guide is started.
While the destination guide is operating, other sound sources may be used
(for example an audio CD), even though the TMC reception will remain active
while the reception is good (Note ⇒page 56, “The destination guide without
the navigation CD”). If you continue li stening to the radio, the tuned radio
station should offer the TMC service.
If the signal from the TMC station is lost, the radio and navigation system
searches for another similar type station.
If, however, “ maintain without TMC ” has been selected or no TMC station is
being received, the message “ No TMC station registered.” is displayed. It is
END GUIDE
BEGIN GUIDE
TRAFFIC
ROUTE OPTIONS
ROUTE
RNS MP3_ingles Seite 51 Mittwoch, 10. Mai 2006 7:52 19

Navigation
54
– Press the button to show the destination or the itinerary on
the main navigation menu.
– In the main navigation menu, press the function to return to the symbol representation.
– The button may be used to repeat the last audio indication ⇒ .While the guide is working, the following destination is marked with an arrow
on the main navigation menu ⇒ page 53, fig. 27
.
More information can be found on the volume settings for the audio indica-
tions in the ⇒ page 9, “Sound, sound focus and volume” ( Navigation
volume )
Other audio indication settings ⇒page 48, “Navigation settings (SETUP)”.
Once the route is calculated, the first indication is heard, for example “Turn
right for the next exit”. The road current ly used is indicated on the lower part
of the screen in the symbol representation mode ⇒page 53, fig. 26 . Up to
three announcements will be made befo re a turn has to be made to ensure
that you are informed in time, for exampl e “Approaching left turn”, “Turn left
after 200 metres” and “Now turn left”. A proximity bar will be shown in the
display on the right-hand side of th e turn arrow shortly before the last
announcement is made. The proximity bar shows how far away the turning
point is. After turning, the distance to the next direction change is displayed
here (note the Tyre calibration in the ⇒ page 48, “Navigation settings
(SETUP)”)
You will receive a recommendation for a lane on roads with more than one
lane that then separate off in different directions, for example “Now, take the
left hand side lane.” and “Now, use the left hand side lane”.
You will also be told which exit to us e off a roundabout before entering it, e.g.
“Leave roundabout by the second exit.” In a roundabout this means “Turn at
the second exit to the right”. An announcement will be made when you reach your destination. If the navi-
gation CD contains the destination street, you will hear the following
message: “You have reached your destination”, otherwise “You have reached
the destination area”. The latter may occur if you have entered the destina-
tion using coordinates and the destination is not included on in the CD infor-
mation.
If an intermediate destination is reac
hed, the indication “You have reached
and intermediate destination” is given th en “Calculating route” or “The route
to intermediate destinatio n is being calculated” if there is an intermediate
destination on the route. The route calculation to the following destination
begins automatically ( ⇒page 50, “Begin/cancel destination guide”).
WARNING
•
As all drivers, you must concentrate on traffic. The indications made on
the basis of the information on the CD may differ from what you actually see
due to incomplete data or a different road layout (e.g. due to road works).
Please keep to traffic regulations and ignore the navigation recommenda-
tions if necessary.
•
Traffic signs and legislation always have priority over the recommenda-
tions made by the system.
•
Please observe the important safety warnings ⇒page 34, “Safety”.Note
Note that the proximity bars and the audio navigation indications only reflect
“real” measurements if the tyre di ameter has been correctly set (Tyre
calibration in ⇒page 48, “Navigation settings (SETUP)”).
NAV
SYMBOLS
INFO
RNS MP3_ingles Seite 54 Mittwoch, 10. Mai 2006 7:52 19