2007 SATURN VUE clock

4. Insert a at blade tool through the opening in
the top. Make sure the tool ts through the
opening in the headlamp bracket lower arm.5. Push the locking tab toward the rear of the
vehicle with the tool to lift the headlamp
bracket lower arm.
6. Pull back on the front fascia and then pull the
headlamp assembly out from the vehicle. You
may need someone to assist you with this step.
7. Disconnect the electrical connector from the
bulb assembly.
8. Turn the bulb assembly counterclockwise to
remove it from the housing.
9. Replace the old bulb with a new one.
10. Reverse Steps 1 through 8 to reinstall.
360
ProCarManuals.com

Front Turn Signal and
Parking Lamps
To replace a front turn signal or parking lamp
bulb, do the following:
1. Follow Steps 1 through 6 underHeadlamps
on page 358to access the front turn signal
or parking lamp.
2. Turn the bulb to be replaced counterclockwise
to remove it from the headlamp assembly.
3. Pull the bulb out of the bulb socket assembly.
4. Push the new bulb into the bulb socket
assembly.
5. Insert the bulb assembly into the headlamp
assembly.
6. Turn the bulb assembly clockwise until
seated.
7. Reverse the steps to reinstall the headlamp
assembly.
361
ProCarManuals.com

Taillamps, Turn Signal, Stoplamps
and Back-up Lamps
To replace one of these bulbs, do the following:
1. Open the liftgate. SeeLiftgate on page 103for
more information.
2. Remove the two screws retaining the taillamp
assembly.
3. Slide the taillamp
assembly rearward
and away from
the vehicle.
4. Disconnect the electrical connector and
remove it from the taillamp assembly.5. Turn the bulb socket being replaced
counterclockwise to disconnect it.
6. Pull the bulb out of the bulb socket.
7. Push the new bulb into the bulb socket.
8. Reverse Steps 2 through 4 to reinstall the
taillamp assembly.
363
ProCarManuals.com

License Plate Lamp
To replace one of these bulbs, do the following:
1. Remove the two screws holding each of
the license plate lamps to the fascia.
2. Turn and pull the license plate lamp forward
through the fascia opening.
3. Turn the bulb socket counterclockwise and
pull the bulb straight out of the socket.
4. Install the new bulb.
5. Reverse Steps 1 through 3 to reinstall the
license plate lamp.
Replacement Bulbs
Exterior Lamp Bulb Number
Back-up 3156
CHMSL W5W
Front Turn Signal/Parking 3157K
Headlamps
High-beam 9005 or HB3
Low-beam/DRL 9006 or HB4
Rear Turn Signal, Stoplamp and
Taillamp3057
For replacement bulbs not listed here, contact
your dealer/retailer.
Windshield Wiper Blade
Replacement
Windshield wiper blades should be inspected for
wear and cracking. SeeScheduled Maintenance
on page 420for more information.
Replacement blades come in different types and
are removed in different ways. For proper type and
length, seeNormal Maintenance Replacement
Parts on page 434.
364
ProCarManuals.com

5. Remove the wheel retainer bolt holding down
the spare tire by turning it counterclockwise.
6. Remove the compact spare tire. SeeCompact
Spare Tire on page 398for more information.The tools you will be using include the jack (A)
and wheel wrench (B).
390
ProCarManuals.com

Removing the Flat Tire and
Installing the Spare Tire
The wheel cover or hubcap needs to be removed
in order to reach the wheel bolts.
For steel wheels with full plastic covers and
aluminum wheels with large circular center caps,
do the following:
1. It is recommended that a safety check is done
before preceding. SeeChanging a Flat Tire
on page 386for more information.
2. Loosen all plastic
caps by turning the
wheel wrench
counterclockwise.
Do not try to remove
plastic caps from
the cover or
center cap.
3. Pull the cover or center cap away from the
wheel and place it in the trunk.When reinstalling full plastic covers or center
caps, tighten all the plastic caps hand snug, then
tighten with the wheel wrench an additional
one-quarter of a turn.
1. Use the wheel wrench to loosen all the wheel
nuts. Do not remove them yet.
2. Attach the wheel
wrench to the jack
bolt head and
rotate the wheel
wrench clockwise.
That will raise the lift
head a little.
391
ProCarManuals.com

{CAUTION:
Lifting a vehicle and getting under it to do
maintenance or repairs is dangerous
without the appropriate safety equipment
and training. The jack provided with your
vehicle is designed only for changing a
at tire. If it is used for anything else, you
or others could be badly injured or killed
if the vehicle slips off the jack. Use the
jack provided with your vehicle only for
changing a at tire.
Notice:Make sure that the jack lift head is
in the correct position or you may damage your
vehicle. The repairs would not be covered by
your warranty.5. Raise the vehicle by turning the jack handle
clockwise. Raise the vehicle far enough off
the ground so there is enough room for
the road tire to be removed.
393
ProCarManuals.com

8. Remove any rust or
dirt from the wheel
bolts, mounting
surfaces and
spare wheel.
9. Place the compact spare tire on the
wheel-mounting surface.
{CAUTION:
Never use oil or grease on studs or nuts.
Because the nuts might come loose. The
vehicle’s wheel could fall off, causing a
serious accident.
10. Reinstall the wheel nuts. Tighten each nut by
hand until the wheel is held against the hub.11. Lower the vehicle by turning the jack handle
counterclockwise.
395
ProCarManuals.com