2007 RENAULT SCENIC air condition

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-22V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09
DF038
PRESENT
OR
STOREDANGLE SENSOR
1.DEF: Sensor internal electrical fault
2.DEF: Absence of sensor signal
3.DEF: Values outside limits
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after having started the engine and turned the steering
wheel from lock to lock.
Notes:
This fault causes an absence of steering wheel return (no warning light or message).
–The computer records an occurrence context (computer operating values frozen
when fault occurs). To view this information, click on the fault description (camera
symbol). Within these values, parameter PR143 Internal fault code gives the fault
finding procedure to apply.
Procedure to apply for internal fault codes 195 and 196 of PR143.
Position the vehicle wheels in the straight line driving position (steering centre point).
Refer to parameters PR121 Steering wheel angle and PR007 Steering wheel angle offset compensation.
Both parameters must be between - 10˚ < X < 10˚.
Turn the steering wheel to full right lock then to full left lock, and check that the parameter varies within the
tolerances given in the "Conformity check".
Refer to status ET020 Steering wheel angle sensor programming, which must be STATUS 4.
If parameters PR121, PR007 and status ET020 are not correct:
Place the vehicle on a front axle adjusting bench.
Position the vehicle wheels in the straight line driving position (steering centre point).
Program the steering wheel angle via command VP004 Steering wheel angle sensor programming (see
Configuration and programming, section A).
Remove the fault, start the engine and check that the EPAS functions correctly by turning the steering wheel from
lock to lock (parking manoeuvres).
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF038/DAE_V09_DF038

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-23V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09
DF038
CONTINUED
Procedure to apply for internal fault codes 192, 193 and 194 of PR143.
Check the fault occurrence context for internal fault codes 193 and 194. If PR108 Computer supply voltage
is less than 10 V, the fault is due to a battery undervoltage.
Check the vehicle battery voltage.
Check the tightness and the condition of the battery terminals.
Check the charge circuit if necessary.
Check the condition of the 3 white EPAS connectors and check that they are locked correctly.
In the event of a fault, check the insulation, continuity and the absence of interference resistance on the
following connection:
2-track connector track 1 + 12 V before ignition feed
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-25V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF054
PRESENT
OR
STOREDTORQUE SENSOR
DEF: Sensor internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after having started the engine and turned the steering
wheel from lock to lock, then returning it to the centre.
Notes:
This fault causes:
Loss or absence of steering assistance with STOP warning light + Message
lighting up.
–The computer records an occurrence context (computer operating values frozen
when fault occurs). To view this information, click on the fault description (camera
symbol).
Within these values, parameter PR143 Internal fault code gives the fault finding
procedure to apply.
If, in the fault occurrence context (computer operating values frozen when fault
occurs) PR108 Computer supply voltage is less than 10 V, check the battery
voltage, the tightness and the condition of the battery terminals and check the
charging circuit.
Procedure to apply for internal fault codes 1 and 69 of PR143.
Contact Techline.
Procedure to apply for internal fault codes 48, 66, 64, 65 and 67 of PR143.
Check the condition of the 3 white EPAS connectors and check that they are locked correctly.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF054/DAE_V09_DF054/DAE_V0D_DF054

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-26V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF055
PRESENT
OR
STOREDCOMPUTER MEMORY
DEF: EEPROM irregularity
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after having started the engine and turned the steering
wheel from lock to lock, then returning it to the centre.
Notes:
This fault leads to degraded assistance with no warning light or message or an
assistance that is limited to 10% with the SERVICE indicator light + Message.
–Risk of ESP fault.
–The computer records an occurrence context (computer operating values frozen
when fault occurs). To view this information, click on the fault description (camera
symbol). Within these values, parameter PR143 Internal fault code gives the fault
finding procedure to apply.
Procedure to apply for internal fault codes 83 and 85 of PR143.
Only for Vdiag 05 and 09:
Check status ET020 Steering wheel angle programming which should be STATUS 4; if not, program the
steering wheel angle sensor VP004 Steering wheel angle programming (see Configuration and
programming).
If the fault is still present after the ignition has been switched on several times, contact the Techline.
Procedure to apply for internal fault codes 84 and 86 of PR143.
Contact Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF055/DAE_V09_DF055/DAE_V0D_DF055

POWER-ASSISTED STEERING
Fault finding – Interpretation of faults
36B
36B-27V5 MR-372-J84-36B000$462_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
DF057
PRESENT
OR
STOREDMULTIPLEX VEHICLE SPEED SIGNAL
DEF: Invalid signal
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after a road test.
Notes:
This fault causes an unsuitable level of assistance and the SERVICE indicator light
+ Message come on.
Carry out fault finding on the multiplex network, and repair if necessary.
Carry out fault finding on the ABS (see 38C, Anti-lock braking system). If the ABS signals no fault and the EPAS
is the only system signalling the fault, contact the Techline.
AFTER REPAIRClear the stored faults.
Check that the EPAS is working.
Deal with any other faults.
DAE_V05_DF057/DAE_V09_DF057/DAE_V0D_DF057

POWER-ASSISTED STEERING
Fault finding – Fault Finding Chart
36B
36B-48V5 MR-372-J84-36B000$924_fra.mif
EPAS
Vdiag no.: 05, 09,
0DPOWER-ASSISTED STEERING
Fault finding – Fault Finding Chart
ALP1 No dialogue with the computer
NOTESNone.
Run fault finding on the multiplex network.
Check the voltage of the vehicle battery (the EPAS system only reacts between 10 V and 18 V).
Repair if necessary.
Try the diagnostic tool on another vehicle.
Check:
–the connection between the diagnostic tool and the diagnostic probe (lead in good condition),
–the connection between the diagnostic sensor and the diagnostic socket (lead in good condition).
Check the condition of the EPAS fuses and their contacts:
80A BP81 Power fuse in the engine fuse box.
5A AP44 + after ignition fuse on the UPC.
Check for the presence of + 12 V battery feed on track 16, and + 12 V after ignition feed on track 1 and an earth
on track 5 and on track 4 of the diagnostic socket.
Repair if necessary.
Disconnect the two EPAS computer connectors.
Check the condition and conformity of the connectors and their clips.
Check the conformity of the electrical supplies (they must be equal to the battery voltage).
Electric Power Assisted Steering Computer Connector:
2-track connector track 1+ battery feed
2-track connector track 2Earth
8-track connector track 8+ After ignition
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the wiring harness between
the diagnostic socket and the Electric Power Assisted Steering computer connector.
Electric Power Assisted Steering Computer Connector:
8-track connector track 5 track 14 Diagnostic socket
8-track connector track 7 track 6 Diagnostic socket
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRPerform a test using the diagnostic tool.
DAE_V05_ALP1/DAE_V09_ALP1/DAE_V0D_ALP1
MR-372-J84-36B000$924_fra.mif

POWER-ASSISTED STEERING
Fault finding – Fault Finding Chart
36B
36B-49V5 MR-372-J84-36B000$924_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
ALP2 Loss of vehicle assistance without warning
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
The vehicle is no longer assisted if the Electric Power Steering fuse is damaged or supply is lost. The steering is
equivalent to manual steering, manoeuvrable when driving even at low speeds, but very difficult to manoeuvre
when stopped.
Since it is no longer being supplied, the EPAS computer is not capable of lighting the warning light, but the
instrument panel lights the STOP warning light + Message 4 seconds after the loss of the feed causing the loss
of assistance.
The driver will only become aware of the fault through noticing the loss of assistance at the steering wheel.
Check the fuses for the electric power-assisted steering:
Power fuse 80A BP81 in the engine fuse box.
5A AP44 + after ignition fuse on the UPC.
Check the condition of the electric power-assisted steering connectors and repair if necessary.
Check that the electrical feeds to the computer are correct:
2-track connector track 2vehicle earth
2-track connector track 1+ battery feed
8-track connector track 8+ after ignition feed
Repair if necessary.
Check the insulation, continuity and the absence of interference resistance on the connections between the electric
power-assisted steering computer and the instrument panel.
8-track connector track 6 track 30 of the instrument panel
8-track connector track 4 track 29 of the instrument panel
Check that the steering column and steering rack are in sound mechanical condition.
Repair if necessary.
Make sure that the front axle components, such as the track rod ends and shock absorber base plates, are in sound
mechanical condition.
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRPerform a test using the diagnostic tool.
DAE_V05_ALP2/DAE_V09_ALP2/DAE_V0D_ALP2

POWER-ASSISTED STEERING
Fault finding – Fault Finding Chart
36B
36B-50V5 MR-372-J84-36B000$924_fra.mif
EPAS
Vdiag no.: 05, 09,
0D
ALP3 Poor vehicle handling
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Check the pressure and condition of the tyres, the condition of the joints and the front axle geometry.
Check the vehicle battery voltage and the condition of the battery terminals.
Repair if necessary.
Check the status and presence of the Electric Power Steering system power supply fuse.
Repair if necessary.
Check the insulation, continuity and absence of interference resistance on the wiring harness between the
battery and the 2-track EPAS connector.
Repair if necessary.
Check that status ET026 Computer calibration corresponds to the vehicle equipment.
Configure the computer correctly using the diagnostic tool, if necessary (see Configuration and Programming).
If the fault is still present, contact the Techline.
AFTER REPAIRPerform a test using the diagnostic tool.
DAE_V05_ALP3/DAE_V09_ALP3/DAE_V0D_ALP3