2007 RENAULT SCENIC steering wheel

RADIO
General Information
86A
86A - 2V2 MR-372-J84-86A000$099_eng.mif
186ARADIO
General Information
The tuner-amplifier has a test menu (see radio self-test procedure) to carry out repair operations or fault finding.
The radio will operate for approximately 20 minutes without the ignition being switched to the accessories position.
The radio beeps then switches off.
Diagram:
1Radio
2Aerial
3CD changer
4Speakers/tweeter speakers
5Display
6Steering wheel controls
MR-372-J84-86A000$099_eng.mif

RADIO
General Information
86A
86A - 4V2 MR-372-J84-86A000$099_eng.mif
The radio features allow you to:
–listen to the radio (four geographical zones can be
programmed for FM radio)
–display the name of the station using RDS which
automatically switches to the best transmitter (AF
function),
–receive traffic news (I Traffic function),
–receive news flashes and emergency bulletins
(I News function).
–receive public safety emergency bulletins (PTY 31).
RADIO FUNCTION
The tuner has three selection modes displayed on the
screen and accessible from the radio front panel:
–manual mode (MANU),
–preset mode (PRESET),
–alphabetical mode (LIST).CASSETTE FUNCTION
The cassette plays automatically once cassette mode
has been selected using the steering wheel control or
the front panel.
Only the Dolby fast-forward and rewind with search
controls can be selected by specific buttons.
CD FUNCTION
The CD player can play conventional discs and any
audio tracks on a CD-ROM.
CDs can be played in order or tracks can be chosen at
random.
If a CD changer is being used, random play is possible
on only one of the possible 6 compact discs.
THERMAL PROTECTION
If the radio temperature is too high for it to function
properly, the volume is automatically reduced (without
changing the volume shown in the display).
Should one of the speaker tracks short circuit, the
supply to the amplifier will be cut off.Note:
The Mute function, accessed via the voice
synthesiser or the steering wheel control, stops the
cassette playing.

RADIO
Anti-theft code
86A
86A - 7V2 MR-372-J84-86A000$297_eng.mif
RADIO
Anti-theft code
The radio is protected by a four digit code. This code
must be entered via the control satellite or the radio
keypad each time the battery is disconnected.
Entering the code with the control on the steering
wheel:
Press the lower button on the control to confirm an
entry.
Entry via the radio:
Enter the digits using buttons 1, 2, 3 and 4, and then
confirm with button 6.
If the code is entered incorrectly, the radio will be
locked (1 minute for the first error, 2 minutes for the
second error, 4 minutes for the third error, etc.
32 minutes maximum).
Some configurations must be set after the code has
been entered for the first time (see the Configuration
Section). These settings are stored when the battery is
disconnected.Reminder:
The radio will operate for approximately 2 minutes in
scrambled mode without the code having been entered
(with regular warning beeps).
If the vehicle is equipped with a CD changer in the
front panel, a code is exchanged between the CD
changer and the radio.
–If a new CD changer is fitted, the radio code is
programmed when the battery or CD changer is
connected.
–If the radio is replaced, enter the security code of the
old radio connected to the CD changer. The CD
changer is programmed with the code for the new
radio.
–If the old radio code is lost, the changer code can be
cleared using the clearing code. The clearing code is
issued by the Techline, server, etc.
Note:
If there is a configuration error, you can return to scrambled mode by pressing the 2 and 5 buttons at the same
time as switching the power on. Then wait 2 minutes.
Note:
The CD changer is supplied uncoded. When it is installed in the vehicle, the CD changer is programmed with the
radio supply code.
Reminder:
The radio will operate for approximately 2 minutes in scrambled mode without the code having been entered (with
regular warning beeps).
IMPORTANT
If the vehicle is fitted with a top of the range navigation system (ITS), enter the radio code in the following
way:
1. switch on the system by activating the vehicle's + after ignition feed,
2. wait 2 minutes: scrambled mode with beeps from the speakers, then code request screen appears,
3. enter the radio code using the ITS keypad: move the cursor with the central control and press to confirm.
4. switch off the ignition.
MR-372-J84-86A000$297_eng.mif

RADIO
Anti-theft code
86A
86A - 8V2 MR-372-J84-86A000$297_eng.mif
THE DISPLAY SHOWS 'CODE' OR '0000'
Entering the security code. The radio beeps
every 2 seconds for 2 minutes then displays
CODE.
No
Is the radio code
known?
Yes
Yes
No
Does the radio show
CODE then 0000?
Yes
Enter the first digit using the wheel control on the
steering wheel or the front panel.
Confirm that the digit is correct by briefly
pressing the lower steering wheel button or front
panel button.
Use the same procedure to enter the remaining
three digits.
Confirm the security code by pressing and
holding the same button or button (6) on the front
panel.
No
Does the radio show
ERROR then CODE?
Yes
(See anti-theft code recovery
procedure)
No
Has the 4-digit code
been obtained?
Go back to scrambled mode. With the
radio off, press the 2, 5 and ON buttons.
Wait approximately 2 minutes until CODE
then 0000 appears.
Does the radio show
ERROR CD then CD
CODE?
Yes
See display shows CD CODE.No
The radio enters "CONFIGURATION" mode (if
being used for the first time) and operates
normally.

RADIO
Anti-theft code
86A
86A - 9V2 MR-372-J84-86A000$297_eng.mif
THE DISPLAY SHOWS "CD CODE"
The radio displays ERROR CD,
CD CODE, then CD-0000.
Enter the code of the old radio connected to the
CD changer.
Enter the first digit using the steering wheel
controls.
Confirm the digit by briefly pressing the lower
button of the steering wheel controls.
Enter the three other digits using the same
procedure.
Confirm the security code by pressing and
holding the same button.
Does the CD changer
code match the radio
code?
Yes
No
Enter the CD changer resetting code obtained
from the Techline. After following the
procedure, the display shows CODE or 0000.The CD changer has registered the new radio
code and operates correctly.

RADIO
Connections
86A
86A - 11V2 MR-372-J84-86A000$495_eng.mif
RADIO
Connections
To allocate the tracks for the different functions that are connected to the radio (CD changer, steering wheel control,
display, aerial), refer to the Wiring Diagrams Technical Note corresponding to the vehicle.
Radio: see Wiring diagrams Technical Note, vehicle, code 261
CD changer: see Wiring diagrams Technical Note, vehicle, code 1272
Display: see Wiring diagrams Technical Note, vehicle, code 1127
For displays which are connected to the instrument panel, the code is 247
Steering wheel control: see Wiring diagrams Technical Note, vehicle, code 325
Aerial: see Wiring diagrams Technical Note, vehicle, code 886
MR-372-J84-86A000$495_eng.mif