AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart23A
23A -131V5 MR-372-J84-23A100$928.mif
SIEMENS TA2005
Vdiag No.: 14-18
ALP3
CONTINUED 1
Check the oil level.
Check the oil pressure using PR003 Oil pressure:
Warm engine with gearbox oil temperature between 65 and 90˚C.
Measure the line pressure under the 3 following conditions:
IMPORTANT
The vehicle must be stationary: handbrake on and brake pedal depressed, no accessories operating
(e.g.: air conditioning)
1engine speed idling:
Shift the gear lever to R, N and D, the pressure reading must be greater than 2.5 bars.
2engine speed at 1200 rpm:
–gear lever in R position, the pressure reading must be greater than 4 bars.
–gear lever in D position, the pressure reading in first gear must be greater than 5.5 bars.
3engine speed at 2200 rpm:
–gear lever in R position, the pressure reading must be greater than 11 bars.
–gear lever in D position, the pressure reading in first gear must be greater than 11 bars.
Do the recorded values correspond to the specified values?
Shift the gear lever into position D and monitor
PR007 Turbine speed when accelerating.Replace the pressure modulating solenoid valve
and the oil. Repeat the check after replacement.
If the fault is still present, replace the hydraulic
distributor and all the solenoid valves (see MR 364
Mechanical, 23A, Automatic transmission,
Hydraulic distributor (for Mégane II) and MR 370
Mechanical, 23A, Automatic transmission,
Hydraulic distributor (for Scénic II)).
Does the turbine speed change?
Replace the automatic transmission (see MR 364, Mechanical, 23A,
Automatic transmission, Removal-Refitting (for Mégane II) and MR
370, Mechanical, 23A, Automatic transmission, Removal-Refitting
(for Scénic II)).
A
YESNO
NOYES
B
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart23A
23A -133V5 MR-372-J84-23A100$928.mif
SIEMENS TA2005
Vdiag No.: 14-18
ALP4 Automatic transmission malfunctioning on gear changing
NOTESOnly refer to Customer complaints after carrying out a complete fault finding
procedure with the diagnostic tool and the conformity check.
Automatic transmission malfunctions may be noted during gear changing without any fault being stored in the
computer.
These malfunctions may be linked to:
–connection faults (insulation: creates a fault, resistance) in the sequence solenoid valve control wiring
harnesses (EVS1 to EVS6).
Check the tightness and condition of the clips on all the solenoid valve control wiring connections from the
computer to each solenoid valve.
Use command AC024 Sequential actuators control to find any faults.
–Hydraulic distributor faults (hydraulic slide valve seizing, strainer/distributor seal) preventing the sequence
solenoid valves from working properly.
Check the oil's condition (colour, burnt or not) its level and pressure: increasing with engine/turbine speed.
–Loss of pressure when changing gear (clutch brakes/cylinder leaks)
Read the values of the following parameters (gear lever in position D or R: vehicle stationary and handbrake
applied) on the CLIP tool:
–PR003 Oil pressure,
–PR006 Engine speed,
–PR007 Turbine speed,
–PR138 Reference pressure,
–PR008 Computer feed voltage.
These parameters are associated with automatic transmission operation.
If one of the values is incorrect, note the fault it causes.
Replace the faulty part if necessary and carry out a check.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
DP0TA2005_V14_ALP04/DP0TA2005_V18_ALP04
AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart23A
23A -134V5 MR-372-J84-23A100$928.mif
SIEMENS TA2005
Vdiag No.: 14-18
ALP5 Erratic gear changes
NOTESOnly refer to Customer complaints after carrying out a complete fault finding
procedure with the diagnostic tool and the conformity check.
Run a multiplex network test (see 88B, Multiplex).
Check for the following parameters:
–PR135 Standard pedal position,
–PR136 Raw pedal position.
Carry out a road test using the diagnostic tool, making sure that status ET013 Gear engaged operates normally.
If the customer complaint occurs with the brake pedal released, check that status ET004 Brake light switch
(Closed) is NO.
If not, adjust the brake light switch and the brake pedal.
Make sure that the instrument panel display of the gear engaged matches the gear lever position.
Check the automatic transmission wiring harness (sequence solenoid valve control).
Replace it if necessary.
Check that the gear lever cable is working properly and adjust it if necessary.
Check that the multifunction switch is working correctly.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
DP0TA2005_V14_ALP05/DP0TA2005_V18_ALP05
