2007 RENAULT SCENIC service

2Transmission
V5 MR-372-J84-23A100$TOC.mif
V5
23A
"The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The procedures may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from
which his vehicles are constructed."
V5
All rights reserved by Renault s.a.s.
Edition Anglaise
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault s.a.s.
© Renault s.a.s. 2007
AUTOMATIC TRANSMISSION
SIEMENS TA2005
Vdiag No.: 14-18
Fault finding - Introduction 23A - 2
Fault finding - System operation 23A - 7
Fault finding - Replacement of components 23A - 12
Fault finding - Configurations and programming 23A - 13
Fault finding - Fault summary table 23A - 14
Fault finding - Interpretation of faults 23A - 16
Fault finding - Conformity check 23A - 73
Fault finding - Status summary table 23A - 88
Fault finding - Interpretation of statuses 23A - 89
Fault finding - Parameter summary table 23A - 108
Fault finding - Interpretation of parameters 23A - 109
Fault finding - Dealing with command modes 23A - 125
Fault finding - Interpretation of commands 23A - 126
Fault finding - Customer complaints 23A - 127
Fault finding - Fault Finding Chart 23A - 128
Fault finding - Tests 23A - 137

Fault finding - Replacement of components23A
23A - 12V5 MR-372-J84-23A100$174.mif
SIEMENS TA2005
Vdiag No.: 14-18AUTOMATIC TRANSMISSION
Fault finding - Replacement of components
REPLACING THE COMPUTER
If Techline approves the computer replacement, proceed as follows:
–Note the gearbox oil condition meter code in the Identification menu: ID018 Oil condition meter and the
date of the last gearbox oil service ID017 Gearbox oil service date.
–Switch off the ignition.
–Replace the computer.
–If necessary, change the computer configuration in the Enter configuration menu.
–Enter the VIN into the computer with diagnostic tool command VP001 Enter VIN.
–Enter the oil condition meter code from the old automatic transmission computer (found in the Identification
menu) using command VP015 Transfer oil condition meter.
–Enter the gearbox oil service date with command VP016 Enter gearbox oil service date.
–Enter the After-Sales service date with diagnostic tool command VP009 Enter last After-Sales service
date.
–Carry out a check with the diagnostic tool, on the Identification screen.
–Switch off the ignition.
REPLACING AN AUTOMATIC TRANSMISSION COMPONENT
To replace other components of the automatic transmission, (see MR 364 Mechanical, 23A, Automatic
transmission (for MEGANE II) and see MR 370 Mechanical, 23A, Automatic transmission (for SCENIC II)).
After replacing one or more automatic transmission components, or after reprogramming, auto-program the solenoid
valves using command RZ005 "Auto-adaptives" (see Dealing with command modes).IT IS ESSENTIAL TO CONTACT YOUR TECHLINE BEFORE REPLACING AN AUTOMATIC TRANSMISSION
COMPUTER.
MR-372-J84-23A100$174.mif

Fault finding - Configurations and programming23A
23A - 13V5 MR-372-J84-23A100$232.mif
SIEMENS TA2005
Vdiag No.: 14-18AUTOMATIC TRANSMISSION
Fault finding - Configurations and programming
PROGRAMMING
●VP001 Enter VIN:
As it is necessary to enter the VIN each time dialogue is established with the diagnostic tool, it must be
programmed into each vehicle computer whenever a computer is replaced.
Programming procedure:
–Connect the diagnostic tool.
–Consult the fault finding procedure for the automatic transmission.
–Select configuration VP001 Enter VIN.
–Enter the VIN.
–Exit fault finding mode.
–Switch off the ignition.
–Wait for the end of Power-latch: over 10 seconds.
●VP009 Enter last After-Sales operation date:
Every time work is carried out on the automatic transmission in the workshop, enter the date of the
operation.
Select command VP009 Enter last After-Sales operation date on the diagnostic tool, then use the tool's
keypad to enter the date of the operation.
●VP015 Transfer oil condition meter:
Transfer the oil wear counter code from the old computer.
Select command VP015 Transfer oil wear counter on the diagnostic tool, then use the keypad to enter
the code found on the replaced computer.
●VP016 Enter gearbox oil service date:
Select command VP016 Enter gearbox oil service date on the diagnostic tool, then use the keypad to
enter the date found on the replaced computer.
* The immobiliser warning light will flash a few seconds after the ignition is switched off.
MR-372-J84-23A100$232.mif