2007 RENAULT SCENIC wiring

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 2V2 MR-372-J84-38C050$062_eng.mif
138C
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP
Special tooling required
3. RECAP
Procedure
To perform fault finding on the vehicle's computers, switch on the ignition in fault finding mode.
Proceed as follows:
–vehicle's card in reader;
–press and hold the Start button (longer than 5 seconds) with start-up conditions not present,
–connect the diagnostic tool and perform the required operations.
To cut off + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–press the Start button twice briefly (less than 3 seconds),
–ensure that the + after ignition feed has been cut off by checking that the computer indicator lights on the instrument
panel have gone out. Vehicle(s): MEGANE II, SCENIC II
Function concerned: ESPName of computer: ESP 8.0
Vdiag No.: 08, 09, 0A, 0B, 11 and 12
Special tooling required
Multimeter
Elé. 1681 Universal bornier
Note:
The left and right-hand xenon bulb computers are supplied when the dipped headlights are lit. Therefore fault
finding can only be carried out on them after the ignition has been switched on in fault finding mode (forced + after
ignition feed) and the dipped headlights have been switched on.
ESPBOSCH_V08_PRELI /ESPBOSCH_V09_PRELI /ESPBOSCH_V0A_PRELI/
ESPBOSCH_V0B_PRELI /ESPBOSCH_V11_PRELI/ESPBOSCH_V12_PRELI
MR-372-J84-38C050$062_eng.mif

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 5V2 MR-372-J84-38C050$062_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
4. FAULT FINDING PROCEDURE (continued)
Wiring check
Fault finding problems
Disconnecting the connectors and/or manipulating the wiring harness may temporarily remove the cause of a fault.
Electrical measurements of voltage, resistance and insulation are generally correct, especially if the fault is not
present when the analysis is made (stored fault).
Visual inspection
Look for damage under the bonnet and in the passenger compartment.
Carefully check the fuses, insulators and wiring harness routing.
Look for signs of oxidation.
Tactile inspection
While manipulating the wiring harness, use the diagnostic tool to note any change in fault status from stored to
present.
Make sure that the connectors are properly locked.
Apply light pressure to the connectors.
Twist the wiring harness.
If there is a change in status, try to locate the source of the fault.
Inspection of each component
Disconnect the connectors and check the appearance of the clips and tabs, as well as the crimping (no crimping on
the insulating section).
Make sure that the clips and tabs are properly locked in the sockets.
Check that no clips or tabs have been dislodged during connection.
Check the clip contact pressure using an appropriate model of tab.
Resistance check
Check the continuity of entire lines, then section by section.
Look for a short circuit to earth, to + 12 V or to another wire.
If a fault is detected, repair or replace the wiring harness.

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 15V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
DF001
PRESENT
OR
STOREDCOMPUTER SUPPLY VOLTAGE
1.DEF : below minimum threshold
2.DEF : above maximum threshold
3.DEF : abnormal voltage
NOTESSpecial notes:
The fault appears during a road test at a vehicle speed of > 6 mph (10 km/h). The
computer signals an external supply fault.
Conditions for applying the fault finding procedure to stored faults:
Apply the fault finding procedure whether the fault is present or stored.
Check the condition and connection of the battery terminals.
Check the condition and position of the ABS/ESP fuses in the engine fuse and relay box.
Check the 50A power fuse in position 5 on the power fuse board.
Check fuse F13 (25A) on the UPC and the correct locking of the grey 4-track PPH1 connector (Vdiag 44) or
the 25A fuse F8 on the UPC and the correct locking of the black 6-track CM connector (Vdiag 48).
Check the connection and condition of the tab 1 red wire of the grey connector.
Check the connections on the ABS/ESP computer 46-track connector.
Check the ABS earths on tracks 1 and 4 (mounted under the ABS/ESP unit) and visually inspect all the
ABS/ESP wiring.
Check the continuity between the fuses and tracks 2 and 3 of the computer connector (+ before ignition feed on
the tracks) and between the UCH and track 28 of the computer (+ after ignition feed on the track).
Clear the computer fault memory. Switch off the ignition.
Switch on the ignition again and carry out a new check using the diagnostic tool.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF001 /ESPBOSCH_V09_DF001/ESPBOSCH_V0A_DF001/
ESPBOSCH_V0B_DF001 /ESPBOSCH_V11_DF001/ESPBOSCH_V12_DF001
MR-372-J84-38C050$434_eng.mif

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 0938C
38C - 16V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09
DF006
PRESENT
OR
STOREDFRONT LEFT-HAND WHEEL SPEED SENSOR CIRCUIT
CO.0 : open circuit or short circuit to earth
1.DEF : internal electronic fault of the sensor
2.DEF : magnetic/mechanical target fault
Vdiag No.: 08 and 09
NOTESSpecial notes:
The wheel speed sensors are supplied with + 12 V after ignition but it is not possible
to measure this feed on Vdiag 08 and 09 (supply cut off when the sensor is faulty).
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
CO.0
NOTESNone
Check the connection and the condition of the sensor connectors.
Swap the two front wheel speed sensors over.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially displayed, DF006 Front left-hand wheel speed sensor circuit, changes to DF026 Front
right-hand wheel speed sensor circuit present, replace the wheel speed sensor.
–If the fault remains on the same side, the wiring between the computer and the sensor is faulty.
Check the connection and the condition of the computer connections. Repair if necessary.
Check and ensure the continuity of the following connections:
Sensor connector one of the two tracks Track 5 computer connector
Sensor connector the other track Track 26 computer connector
Also check the insulation between these two connections.
Repair if necessary.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF006 /ESPBOSCH_V09_DF006

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 0A, 0B, 11, 1238C
38C - 18V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 0A, 0B, 11,
12
DF006
PRESENT
OR
STOREDFRONT LEFT-HAND WHEEL SPEED SENSOR CIRCUIT
CO.0 : open circuit or short circuit to earth
1.DEF : internal electronic fault of the sensor
2.DEF : magnetic/mechanical target fault
3.DEF : open circuit or short circuit
Vdiag: 0A, 0B, 11, 12
NOTESNone.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
CO.0
3.DEF
NOTESSpecial notes: command AC013 Test wheel speed
sensor supply, must be used only once.
Check the connection and the condition of the sensor connectors.
Disconnect the sensor, run command AC013 Test wheel speed sensor supply and check that voltage pulses of
approximately 12 V are detected by a multimeter at the sensor connector terminals on the computer side.
Are voltage pulses detected?
YES
The wiring between the computer and the sensor, as well the supply via the computer,
is OK.
Front left-hand wheel speed sensor fault - replace the sensor.
Check the connection and the condition of the computer connections. Repair if
necessary.
Check and ensure the continuity of the following connections:
Sensor connector, one of the
two tracksTrack 5 computer connector
Sensor connector, the other trackTrack 26 computer connector
Also check the insulation between these two connections. If all the checks are in order,
contact Techline.
NO
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V0A_DF006 /ESPBOSCH_V0B_DF006/
ESPBOSCH_V11_DF006/ESPBOSCH_V12_DF006

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 0938C
38C - 20V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09
DF007
PRESENT
OR
STOREDREAR LEFT-HAND WHEEL SPEED SENSOR CIRCUIT
CO.0 : open circuit or short circuit to earth
1.DEF : internal electronic fault of the sensor
2.DEF : magnetic/mechanical target fault
Vdiag No.: 08 and 09
NOTESSpecial notes:
The wheel speed sensors are supplied with + 12 V after ignition but it is not possible
to measure this supply on Vdiag 08 and 09 (supply cut off when the sensor is faulty).
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
CO.0
NOTESNone
Check the connection and the condition of the sensor connectors.
Swap the two rear wheel speed sensors over.
Clear the computer's fault memory.
Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially displayed, DF007 Rear left-hand wheel speed sensor circuit, changes to DF027 Rear
right-hand wheel speed sensor circuit, replace the wheel speed sensor.
–If the fault remains on the same side, the wiring between the computer and the sensor is faulty.
Check the connection and the condition of the computer connections. Repair if necessary.
Check the connections (Track 31 and 32) at the R2 black 52-track intermediate connection beneath the front
left-hand seat. Repair if necessary.
Check and ensure the continuity of the following connections:
Sensor connector one of the two tracks Track 6 computer connector
Sensor connector the other track Track 27 computer connector
Also check the insulation between these two connections. If the connections are faulty, carry out the following
checks:
Check the continuity, insulation and absence of interference resistance between:
Computer connector track 6 Track 32 on the intermediate connector
Computer connector track 27 Track 31 on the intermediate connector
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF007 /ESPBOSCH_V09_DF007

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 0938C
38C - 21V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09
DF007
CONTINUED
Vdiag No.: 08 and 09
Also check the insulation between these two connections. Repair or replace the wiring if necessary.
Check the continuity, insulation and absence of interference resistance between:
Sensor connector one of the 2 tracks Track 31 on the intermediate connector
Sensor connector the other track Track 32 on the intermediate connector
Also check the insulation between these two connections.
Repair or replace the wiring if necessary.
1.DEF
NOTESNone
Replace the rear left-hand wheel speed sensor.
2.DEF
NOTESNone
Visually inspect the condition of the target and sensor (for dirt, metallic contamination, bearing grease, etc.), and
clean using compressed air if necessary.
If there is a lot of grease on the target, contact the Techline.
Check that the wheel speed sensor mounting is in good condition.
Check the sensor/target air gap through one wheel revolution: 0.1 mm < Rear wheel air gap < 1.2 mm.
Check the conformity of the target (condition, number of teeth = 48) using the specific command SC001 Check
target teeth.
If the checks are correct:
–the computer fault memory has been cleared,
–exit fault finding mode, switch off the ignition and carry out a road test.
Replace the rear left-hand "disc-hub-bearing" assembly (see MR 364 or MR 370 Mechanical, 33A, Rear axle
components, Bearing: Removal - Refitting) if the fault reappears.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 0A, 0B, 11, 1238C
38C - 22V2 MR-372-J84-38C050$434_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 0A, 0B, 11,
12
DF007
PRESENT
OR
STOREDREAR LEFT-HAND WHEEL SPEED SENSOR CIRCUIT
CO.0 : open circuit or short circuit to earth
1.DEF : internal electronic fault of the sensor
2.DEF : magnetic/mechanical target fault
3.DEF : open circuit or short circuit
Vdiag: 0A, 0B, 11, 12
NOTESNone
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present following a road test at a speed of > 36 mph (60 km/h).
CO.0
3.DEF
NOTESSpecial notes:
Command AC013 must only be used once
Check the connection and the condition of the sensor connectors.
Disconnect the sensor, run command AC013 Test wheel speed sensor supply and check that voltage pulses of
approximately 12 V are detected by a multimeter at the sensor connector terminals on the computer side.
Are voltage pulses detected?
YES
The wiring between the computer and the sensor, as well the supply via the computer,
is OK.
Rear left-hand wheel speed sensor fault - replace the sensor.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V0A_DF007 /ESPBOSCH_V0B_DF007/
ESPBOSCH_V11_DF007/ESPBOSCH_V12_DF007