2007 RENAULT SCENIC ESP

38C-81
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
ALP 13 Faulty brake lights lighting
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Using the diagnostic tool, check that ET017 is functioning correctly.
If not, apply the fault finding procedure described above for ET017.
If the lights still do not work, check the functioning of the light-switch relay.
The relay is passed at rest (check the continuity between tracks 3 and 4 of the relay). Replace the relay if
necessary.
Check the continuity of the connection between track 1 of the brake light switch and track 4 of the relay mounting.
Repair if necessary.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP13 /ESPBOSCH_V09_ALP13/ESPBOSCH_V0A_ALP13/
ESPBOSCH_V0B_ALP13 /ESPBOSCH_V11_ALP13/ESPBOSCH_V12_ALP13BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12

38C-82
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
ALP14 Erratic ESP regulation
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Check that the four tyres on the vehicle are identical.
Using the diagnostic tool, you must ensure that the value of configuration PR063 "Vehicle parameters"
matches the definition of the vehicle undergoing diagnostics.
If necessary, run command VP004 Vehicle parameters using the diagnostic tool to define the appropriate
parameters for the vehicle type.
Check the connection and condition of the combined sensor connector.
Check that the orientation of the combined sensor on the body is correct and that it is correctly mounted.
Calibrate the steering wheel angle in the Electric power-assisted steering domain using the diagnostic tool.
Clear the computer's fault memory and clear the ESP sensor programming (Vdiag 09, 0A, 0B, 12 and 11) with
command RZ003 "ESP sensor programming".
Carry out a road test followed by another check with the diagnostic tool.
If the fault is still present, adjust the axle assembly geometries. Adjust if necessary and calibrate the steering
wheel angle again in the Electric power assisted steering domain using the diagnostic tool.
Clear the computer's fault memory and clear the ESP sensor programming (Vdiag 09, 0A, 0B, 12 and 11) with
command RZ003 "ESP sensor programming".
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP14 /ESPBOSCH_V09_ALP14/ESPBOSCH_V0A_ALP14/
ESPBOSCH_V0B_ALP14 /ESPBOSCH_V11_ALP14/ESPBOSCH_V12_ALP14BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12

38C-83
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
*ASR: Traction control
ALP15ESP warning light comes on with the "ASR* disconnected or off"
message when the current is switched on without pressing the
ESP disconnection button
NOTESConsult this customer complaint only if the "Service", "ABS" and "Brake" warning lights
are not lit.
After disconnecting the battery, it is probable that the electric power steering loses the steering wheel angle
sensor indexing (the electric power steering no longer sends the steering wheel angle signal to the ESP, which is
then disabled).
The ESP system is not faulty, no fault is present in the fault memory, the ESP warning light comes on and the
"ASR disconnected or off" message indicate this transient and reversible status.
To restore the electric power steering indexing and enable the ESP again, it is necessary to:
–switch on the ignition or start the engine (to obtain maximum steering assistance),
–turn the steering wheel slowly to full right lock, to full left lock, then return slowly to the centre point after going
slightly past it,
–the ESP warning light should go out and the message "ASR disconnected or off" should disappear,
–stop the engine and switch off the ignition,
–switch on the ignition, start the engine and see that the warning light no longer lights up.
If the warning light and the message reappear, start the procedure described above again.
If the operation fails again or if this customer complaint appears without the battery having been disconnected, run
fault finding on the electric power steering and repair accordingly.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP15 /ESPBOSCH_V09_ALP15/ESPBOSCH_V0A_ALP15/
ESPBOSCH_V0B_ALP15 /ESPBOSCH_V11_ALP15/ESPBOSCH_V12_ALP15BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12

38C-84
MR-372-J84-38C050$930_eng.mif
V2
38C
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart
ALP 16Intermittent illumination of brake, ESP, ABS, SERVICE and STOP
warning lights and the message "brake failure" on the instrument
panel with no fault codes in the computer
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Check the condition and connection of the
battery terminals.
Is the battery in good condition?
YES
Check the 50A power fuse in position 5 on
the power fuse board. Check fuse F13 (25A)
on the UPC and the correct locking of the
grey 4-track PPH1 connector (Vdiag 44) or
the 25A fuse F8 on the UPC and the correct
locking of the black 6-track CM connector
(Vdiag 48 or higher).
Are the fuses and connectors correct?
YES
Check the connection and condition of the tab
1 red wire of the grey connector.
Is the connector correct?
YES
NOClean the battery terminals.
NOIf the connector is faulty and there is a repair
procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions
for repair), repair the connector, otherwise
replace the wiring.
Replace any faulty fuses. Switch on the ignition
again.
Is the replaced fuse or fuses correct?
NO
Check the insulation to earth between:
–fuse 50A and track 2 of the computer
–fuse 25A and track 3 of the computer
Are the connections correct?
NO YES
Contact the Techline.
If the connection(s) are faulty and there is a repair method
(see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
NO
If the connector is faulty and there is a repair method (see Technical
Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the connector, otherwise replace the wiring.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP16 /ESPBOSCH_V09_ALP16/ESPBOSCH_V0A_ALP16/
ESPBOSCH_V0B_ALP16 /ESPBOSCH_V11_ALP16/ESPBOSCH_V12_ALP16BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12

38C-85
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
ALP 16
CONTINUED
Check the connections on the ABS/ESP
computer 46-track connector.
Is the connector correct?
YES
Check the ABS earths on tracks 1 and 4
(mounted under the ABS/ESP unit) and
visually inspect all the ABS/ESP wiring.
Are the earths correct?
YES
Check the continuity between the fuses and
tracks 2 and 3 of the computer connector
(+ before ignition feed on the tracks) and
between the UCH and track 28 of the
computer (+ after ignition feed on the track).
Is the continuity correct?
YES
If the customer complaint is still present,
contact Techline.
NOIf the connector is faulty and there is a repair
procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions
for repair), repair the connector, otherwise
replace the wiring.
NOIf the connection(s) are faulty and there is a
repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it.
NOIf the connection(s) are faulty and there is a
repair method (see Technical Note 6015A,
Repairing electrical wiring, W iring:
Precautions for repair), repair the wiring,
otherwise replace it.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12