2007 PONTIAC VIBE stop start

Brake System Warning Light
Your vehicle’s hydraulic brake system is divided
into two parts. If one part is not working, the other
part can still work and stop you. For good
braking, though, you need both parts working well.
If the warning light comes on, there is a brake
problem. Have your brake system inspected
right away.
If your vehicle has anti-lock brakes, this light
should come on when you turn the key to START.
If it does not come on then, have it xed so it
will be ready to warn you if there is a problem.When the ignition is on, the brake system warning
light will also come on when you set your
parking brake. The light will stay on if your parking
brake does not release fully. If it stays on after
your parking brake is fully released, it means you
have a brake problem.
If the light comes on while you are driving, pull off
the road and stop carefully. You may notice
that the pedal is harder to push or the pedal may
go closer to the oor. It may take longer to
stop. If the light is still on, have the vehicle towed
for service. SeeAnti-Lock Brake System
Warning Light on page 167andTowing Your
Vehicle on page 259.
{CAUTION:
Your brake system may not be working
properly if the brake system warning light
is on. Driving with the brake system
warning light on can lead to an accident.
If the light is still on after you have pulled
off the road and stopped carefully, have
the vehicle towed for service.
United StatesCanada
166

Anti-Lock Brake System
Warning Light
With the Anti-Lock Brake System (ABS), this light
comes on when the engine is started and can
stay on for several seconds. This is normal.
If the light stays on, turn the ignition to LOCK. If
the light comes on while you are driving, stop
as soon as possible and turn the ignition off. Then
start the engine again to reset the system. If
the light still stays on, or comes on again while
you are driving, your vehicle needs service. If the
regular brake system warning light is not on,
you still have brakes, but you do not have anti-lock
brakes. If the regular brake system warning light
is also on, you do not have anti-lock brakes
and there is a problem with the regular brakes.
SeeBrake System Warning Light on page 166.The ABS warning light comes on briey when you
turn the ignition key to ON. This is normal. If
the light does not come on then, have it xed so it
will be ready to warn you if there is a problem.
Low Tire Pressure Warning Light
This light should come
on briey as you start
the engine.
It will then come on only when a low tire pressure
condition exists.
SeeTire Pressure Monitor System on page 330
for more information.
United StatesCanada
167

This light will also come on during a malfunction in
one of two ways:
Light Flashing— A misre condition has
been detected. A misre increases vehicle
emissions and may damage the emission
control system on your vehicle. Diagnosis and
service may be required.
Light On Steady— An emission control
system malfunction has been detected on your
vehicle. Diagnosis and service may be
required.
If the Light Is Flashing
The following may prevent more serious damage
to your vehicle:
Reducing vehicle speed
Avoiding hard accelerations
Avoiding steep uphill grades
If you are towing a trailer, reduce the amount
of cargo being hauled as soon as it is
possibleIf the light stops ashing and remains on steady,
see “If the Light Is On Steady” following.
If the light continues to ash, when it is safe to do
so, stop the vehicle. Find a safe place to park
your vehicle. Turn the key off, wait at least
10 seconds and restart the engine. If the light
remains on steady, see “If the Light Is On Steady”
following. If the light is still ashing, follow the
previous steps, and see your dealer for service as
soon as possible.
If the Light Is On Steady
You also may be able to correct the emission
system malfunction by considering the following:
Did you recently put fuel into your vehicle?
If so, reinstall the fuel cap, making sure to fully
install the cap. SeeFilling the Tank on page 277.
The diagnostic system can determine if the
fuel cap has been left off or improperly installed.
A loose or missing fuel cap will allow fuel to
evaporate into the atmosphere. A few driving trips
with the cap properly installed should turn the
light off.
171

Oil Pressure Light
If there is a problem
with the oil, this light
may stay on after
you start the engine or
come on while you
are driving.
{CAUTION:
Do not keep driving if the oil pressure is
low. If you do, your engine can become so
hot that it catches re. You or others
could be burned. Check your oil as soon
as possible and have your vehicle
serviced.Notice:Lack of proper engine oil maintenance
may damage the engine. The repairs would
not be covered by your warranty. Always follow
the maintenance schedule in this manual for
changing engine oil.
This indicates that there is not enough oil pressure
to keep the engine properly lubricated and cool.
The engine could be low on oil, or have some
other oil related problem. Have it xed right away.
The oil light could also come on in three other
situations.
When the ignition is on but the engine is not
running, the light comes on as a test to
show you it is working, but the light goes out
when you turn the ignition to START. If it
does not come on with the ignition on,
you could have a problem with the fuse or
bulb. Have it xed right away.
Sometimes when the engine is idling at a
stop, the light could blink on and off. Have
it checked at your dealer.
If you make a hard stop, the light could come
on for a moment. Have it checked at your
dealer.
173

TRAF (Traffic):If TRAF displays, the tuned
station broadcasts traffic announcements. Press
this button to receive the traffic announcement
from the station. TRAF inside brackets displays.
When a traffic announcement broadcasts on
the tuned radio station, you will hear it.
If the station does not broadcast traffic
announcements, press the TRAF button and the
radio seeks to a station that does. When a station
that broadcasts traffic announcements is found,
the radio stops seeking and TRAF inside brackets
displays. If no station is found that broadcasts
traffic announcements, NO TRAFFIC displays.
If the brackets are on the display and TRAF is not,
press the TRAF button to remove the brackets
or use the TUNE knob or the SEEK arrows to go
to a station that broadcasts traffic announcements.
If no station is found that broadcasts traffic
announcements, NO TRAFFIC displays.
The radio plays the traffic announcement if the
volume is low. The radio interrupts the play
of a CD if the last tuned station broadcasts traffic
announcements and the brackets are displayed.
This function does not apply to XM™ Satellite
Radio Service.Radio Messages
If any error occurs repeatedly or if an error cannot
be corrected, contact your dealer.
Radio Messages for XM™ Only
SeeXM Radio Messages on page 216later in this
section for further detail.
Playing a CD
Insert a CD partway into the slot, label side up.
The player pulls it in and the CD should begin
playing. If you insert a CD with the radio off and
the ignition on, it starts to play.
If the ignition or radio is turned off with a CD in
the player, it stays in the player. When the ignition
or radio is turned on, the CD starts playing
where it stopped, if it was the last selected audio
source.
When the CD is inserted, the CD symbol displays
on the CD. As each new track starts to play,
the track number displays.
The CD player can play the smaller 3 inch (8 cm)
single CDs with an adapter ring. Full-size CDs
and the smaller CDs are loaded in the same
manner.
185

4s(Reverse):Press and hold this pushbutton
to reverse quickly within a track. Sound is heard at
a reduced volume. Release the pushbutton to
play the passage. The elapsed time of the track
displays.
EQ (Equalizer):Press EQ to select an
equalization setting while playing a CD. The
equalization is set when a CD is played. See “EQ”
listed previously for more information. If you
select an EQ setting for your CD, it is activated
each time a CD is played.
wSEEKx:Press the down arrow to go to the
start of the current track if more than eight seconds
have played. Press the up arrow to go to the
next track. If either arrow is held or pressed more
than once, the player continues moving backward
or forward through the CD.
wSCANx:Press and hold either arrow for
more than two seconds until SCAN and the track
number displays and a beep sounds. The CD
goes to the next track, plays for a few seconds,
then goes to the next track. Press either arrow
again to stop scanning.RCL (Recall):Push this button to see how long
the current track has been playing. To change the
default on the display, track, and elapsed time,
push the button until the desired option displays,
then hold the button until the display ashes.
The selected display becomes the default. While
elapsed time is showing, CD TIME displays.
BAND:Press this button to listen to the radio
when a CD is playing. The inactive CD remains
inside the radio for future listening.
CD AUX (Auxiliary):Press this button to play a
CD when listening to the radio. The CD symbol
displays when a CD is loaded.
Z(Eject):Press this button to eject a CD. Eject
can be activated with either the ignition or radio
off. CDs can be loaded with the ignition and radio
off if this button is pressed rst.
187

TRAF (Traffic):If TRAF displays, the tuned
station broadcasts traffic announcements.
To receive the traffic announcement from the
tuned station, press this button. Brackets
are displayed around TRAF and when a traffic
announcement broadcasts on the tuned radio
station, you will hear it.
If the station does not broadcast traffic
announcements, press the TRAF button and the
radio seeks to a station that does. When a station
that broadcasts traffic announcements is found,
the radio stops seeking and brackets are displayed
around TRAF. If no station is found that
broadcasts traffic announcements, NO TRAFFIC
displays.
If the brackets are on the display and TRAF is not,
press the TRAF button to remove the brackets
or use the TUNE knob or the SEEK arrows to go
to a station that supports traffic announcements.
If no station is found that broadcasts traffic
announcements, NO TRAFFIC displays.
The radio plays the traffic announcement if the
volume is low. The radio interrupts the play
of a CD if the last tuned station broadcasts traffic
announcements and the brackets display.Playing a CD
Insert a CD partway into the slot, label side up.
The player pulls it in and READING DISC and the
CD symbol displays. If you want to insert a CD
with the ignition off, rst press the eject button or
push the RCL button.
If the ignition or radio is turned off with a CD in
the player it stays in the player. When the ignition
or radio is turned on, the CD starts to play
where it stopped, if it was the last selected audio
source.
When the CD is inserted, the CD symbol displays.
As each new track starts to play, the track
number displays.
The CD player can play the smaller 3 inch (8 cm)
single CDs with an adapter ring. Full-size CDs
and the smaller CDs are loaded in the same
manner.
194

4s(Reverse):Press and hold this pushbutton
to reverse quickly within a track. Sound is heard
at a reduced volume. Release this pushbutton
to play the passage. The elapsed time of the track
displays.
6
!(Previous Folder):This button does not
have a function for non-MP3 CDs.
EQ (Equalizer):Press EQ to select the desired
customized equalization setting while playing
a CD. The equalization is automatically set
whenever a CD is played. See “EQ” listed
previously for more information.
wSEEKx:Press the up arrow to go to the
start of the next track. Press the down arrow to go
to the start of the previous track. Pressing
either arrow for more than two seconds searches
the previous or next tracks at two tracks per
second. When the desired track number displays,
release the arrow to stop searching and to play
the track.
wSCANx:Press and hold either arrow for
more than two seconds until SCAN and the track
number displays and a beep sounds. The CD
goes to the next track, plays for a few seconds,
then goes to the next track. Press either arrow
again to stop scanning.
RCL (Recall):Push this button to see how long
the current track has been playing. To change the
default on the display, track and elapsed time,
push the button until the desired option displays,
then hold the button until the display ashes.
The selected display is now the default. While
elapsed time displays, CD TIME displays.
BAND:Press this button to listen to the radio
when a CD is playing. The inactive CD remains
inside the radio for future listening.
CD AUX (Auxiliary):Press this button to play a
CD when listening to the radio. The CD symbol
displays when a CD is loaded.
Z(Eject):Press this button to eject a CD. Eject
can be activated with either the ignition or radio
off. CDs can be loaded with the radio and ignition
off if this button is pressed rst.
196