2007 PONTIAC GRAND PRIX reset

3. Put the two halves back together. Make sure
the cover is on tight so water will not get
inside the transmitter.
4. Test the operation of the transmitter with the
vehicle.
Remote Vehicle Start
Your vehicle may have a remote start feature.
This feature allows you to start the engine
from outside the vehicle. It may also start the
vehicle’s heating or air conditioning systems and
rear window defogger. When the remote start
system is active, the climate control system will
heat or cool the inside of the vehicle based on the
outside temperature. The rear window defogger
will be turned on by the climate control system
when it is heating the inside of the vehicle. Normal
operation of the system will return after the key
is turned to RUN.
Laws in some communities may restrict the use of
remote starters. For example, some laws may
require a person using remote start to have
the vehicle in view when doing so. Check local
regulations for any requirements on remote starting
of vehicles.Do not use the remote start feature if your vehicle
is low on fuel. Your vehicle may run out of fuel.
The remote start feature provides two separate
starts per ignition cycle, each with 10 minutes of
engine running time.
The remote start system needs to be reset after
your vehicle’s engine is started two times using the
transmitter’s remote start button. The remote
start system is reset by inserting the vehicle’s key
into the ignition switch and turning to RUN.
SeeIgnition Positions on page 105for information
regarding the ignition positions on your vehicle.
Your remote keyless entry transmitter with
the remote start button provides an increased
range of operation. You can start your vehicle from
about 492 feet (150 m) away. However, the
range may be less while the vehicle is running,
and as a result you may need to be closer to your
vehicle to turn it off than you were to turn it on.
There are other conditions which can affect
the performance of the transmitter, seeRemote
Keyless Entry (RKE) System on page 86for
additional information.
90

/(Remote Start):If your vehicle has the remote
vehicle start feature, the keyless entry transmitter
will have a button with this symbol on it.
To start the vehicle using the remote start feature,
do the following:
1. Aim the transmitter at the vehicle.
2. Press and release the transmitter’s lock
button, then immediately press and hold
the transmitter’s remote start button for
4 seconds or until the vehicle’s turn signal
lamps ash. The vehicle’s doors will be
locked.
3. When the vehicle starts, the parking lamps
will turn on and remain on while the engine
is running, and the DIC will display REMOTE
START ACTIVE PRESS HAZARD SWITCH
TO CANCEL.
The engine will shut off automatically after
10 minutes, unless a time extension has been
done or the vehicle’s key is inserted into
the ignition switch and turned to RUN.
If you enter the vehicle after a remote start,
and the engine is still running, insert the
key into the ignition switch and turn to RUN
to drive the vehicle.4. To manually shut off a remote start, do any of
the following. The parking lamps will turn off.
Aim the remote keyless entry transmitter
at the vehicle, and press the remote
start button.
Turn on the hazard warning ashers.
Turn the ignition switch to RUN and then
to OFF.
Your vehicle’s engine can be started two times
using the transmitter’s remote start feature. If only
one remote start procedure has been done,
since last driving the vehicle, or resetting the
remote start system, the engine may be started
again remotely by following the remote start
procedure a second time.
If the remote start procedure is used again before
the rst 10 minute time frame has ended, the
rst 10 minutes will immediately expire and
the second 10 minute time frame will start.
The remote vehicle start feature will not operate if
any of the following occur:
The remote start system is disabled through
the DIC.
The vehicle’s key is in the ignition.
A door on the vehicle is open.
91

Exterior Lamps
The exterior lamp control is located to the left of
the steering wheel on the multifunction lever.
O(Exterior Lamp Control):Turn the band with
this symbol on it to operate the exterior lamps.
The exterior lamp band has four positions:
O(Off):Turning the band to this position turns
off all lamps.
AUTO (Automatic):Turning the band to this
position sets the exterior lamps in automatic mode.
AUTO mode will turn the exterior lamps on and
off depending on how much light is available
outside the vehicle.To override AUTO mode, turn the control to off.
To reset to AUTO mode turn the control to exterior
lamps and then back to AUTO. Automatic mode
will also reset when your vehicle is turned off
and then back on again when the control is left in
the AUTO position.
;(Parking Lamp):Turning the band to this
position turns on the parking lamps together with
the following:
Sidemarker Lamps
Taillamps
License Plate Lamps
Instrument Panel Lights
The parking brake indicator light will come on and
stay on when the parking lamps are on with the
engine off and the ignition to ACC.
5(Headlamps):Turning the control to this
position turns on the headlamps, together with the
previously listed lamps and lights.
144

An indicator light to the right of the button will
come on to show that the recirculation button has
been pressed. The instrument panel brightness
control may have to be adjusted to the highest
setting to see the indicator.
The recirculation mode has a timer. After
ve minutes, the system’s air inlet door will move
slightly to allow for ten percent fresh outside
air to maintain interior air quality. The only way to
reset the system to full recirculation is to restart
the ve minute timer by selecting vent/outside air
and recirculation again.
Rear Window Defogger
The rear window defogger uses a warming grid to
remove fog or frost from the rear window. Be
sure to clear as much snow from the rear window
as possible.
Notice:Do not use a razor blade or sharp
object to clear the inside rear window. Do not
adhere anything to the defogger grid lines
in the rear glass. These actions may damage
the rear defogger. Repairs would not be
covered by your warranty.
=(Rear Window Defogger):Press this button
to turn the rear window defogger on or off.
An indicator light to the right of the button will
come on to show that the rear window defogger is
on. The instrument panel brightness control
may have to be adjusted to the highest setting
during the daytime in order to see the indicator
light.
The rear window defogger will turn off about
20 minutes after the button is pressed. If the button
is pressed again, it will run another 20 minutes.
The defogger can be turned off by pressing
the button again or by turning off the engine.
Do not drive the vehicle until all windows are clear.
z(Heated Seats):Press this button to turn
the heated seats on and off. The button on the left
controls the driver’s seat and the button on the
right controls the passenger’s seat. SeeHeated
Seats on page 10for additional information.
161

The vehicle is equipped with this cluster or one
very similar to it. It has indicator warning lights that
are explained on the following pages. Be sure to
read about them.
Speedometer and Odometer
The speedometer shows the vehicle’s speed in
both miles per hour (mph) and kilometers per
hour (km/h). The odometer, located on the Driver
Information Center (DIC) display, shows how
far the vehicle has been driven, in either miles or
kilometers. SeeDIC Controls and Displays
(Base Level DIC) on page 186orDIC Controls
and Displays (Uplevel DIC with Trip Computer) on
page 190for more information.
If the vehicle has the Head-Up Display (HUD) the
speed will also be displayed on the HUD screen.If a vehicle has to have a new odometer installed,
a new one can be set to the mileage total of
the old odometer, if that can be done. If it cannot,
than it will be set at zero and a label must be
put on the driver’s door to show the old mileage
reading when the new odometer was installed.Trip Odometer
The trip odometer, located in the Driver Information
Center (DIC), tells how far the vehicle has
driven since it was last reset. The miles
(kilometers) for two different trips can be viewed.
SeeDIC Controls and Displays (Base Level
DIC) on page 186orDIC Controls and Displays
(Uplevel DIC with Trip Computer) on page 190for
more information on setting the trip odometer.
170

{CAUTION:
Your brake system may not be working
properly if the brake system warning light
is on. Driving with the brake system
warning light on can lead to an accident.
If the light is still on after you have pulled
off the road and stopped carefully, have
the vehicle towed for service.
Anti-Lock Brake System
Warning Light
If the vehicle has the
Anti-lock Brake System
(ABS), this light will
come on when the
engine is started and
may stay on for several
seconds. That is normal.If the ABS warning light comes on and stays on,
there may be a problem with the anti-lock
portion of the brake system. If the brake system
warning light is not on, the vehicle still has brakes,
but it does not have anti-lock brakes. SeeBrake
System Warning Light on page 176.
If the light stays on, the vehicle needs service.
If the light comes on while the vehicle is being
driven, stop as soon as possible and turn the
ignition off. Then start the vehicle again to reset the
system. If the light still stays on, or comes on again
while driving, the vehicle needs service. If the
regular brake system warning light is not on, the
vehicle still has brakes, but it does not have
anti-lock brakes. If the brake system warning light is
also on, the vehicle does not have anti-lock brakes
and there is a problem with the regular brakes. See
Brake System Warning Light on page 176. If both
the brake system warning light and the anti-lock
brake system light is on, pull off the road and have
the vehicle towed for service.
The anti-lock brake system warning light will come
on briey when the ignition key is turned to
RUN. This is normal. If the light does not come on
then, have it xed so it will be ready to warn
you if there is a problem.
177

When the indicator nears empty, there is still a
little fuel left, but you should get more soon.
Here are four things owners usually ask about the
fuel gage. All these situations are normal and
do not indicate a problem with the fuel gage:
At the gas station the pump shuts off before
the gage reads full.
It takes more or less fuel to ll up than the
gage indicates. For example, the gage
reads half full, but it took more or less than
half the tank’s capacity to ll it.
The gage pointer may move while cornering,
braking or speeding up.
The gage may not indicate full when the
ignition is turned off.
Driver Information Center (DIC)
The Driver Information Center (DIC) gives
important safety and maintenance facts. When the
vehicle’s ignition is turned on, all of the DIC
lights illuminate for a few seconds and an
introductory message will appear. After this, the
DIC will begin working.
DIC Controls and Displays
(Base Level DIC)
The Driver Information Center (DIC) control
buttons and the message display screen are
located above the radio. The DIC gives important
safety and maintenance facts concerning the
vehicle. The status of many of the vehicle’s
systems along with driver personal programming
mode menus and warning messages about
the vehicle’s systems may display on the DIC
screen.
The vehicle’s transaxle position will also appear.
The buttons on the base level are trip odometer,
set/reset, and options.
186

Trip Odometer
3(Trip Odometer):Press this button to access
the odometer and trip distance modes.
The rst menu on the DIC screen will be the
odometer reading, or cumulative mileage of the
vehicle. The odometer cannot be reset.
Press the trip odometer button to advance to the
next menu.
Trip Distances:This menu shows the distances
that the vehicle has driven between specic
points. The trip odometer will record the number of
miles up to 9,999.9 miles or 9 999.9 km travelled
for up to two trips. When 9,999.9 miles or
9 999.9 km is reached for either trip, the odometer
for that trip will go back to zero.
Press the trip odometer button again to access
TRIP A. Press the trip odometer button again
to access TRIP B. To reset the trip odometer(s)
back to zero miles or kilometers, access the trip to
reset and press the set/reset button.The trip odometer has a feature called the
retro-active reset. This can be used to set the trip
odometer to the number of miles or kilometers
driven since the ignition was last turned on. This
can be used if the trip odometer was not reset
at the beginning of the trip.
To use the retro-active reset feature, press and
hold the set/reset button for at least three seconds.
The trip odometer will display the number of
miles or kilometers driven since the ignition was
last turned on and the vehicle began moving. Once
the vehicle has begun moving, the trip odometer
will accumulate mileage. For example, if the
vehicle was driven 5.0 miles (8.0 km) before the
vehicle is started again, and then the retro-active
reset feature is activated, the display will show
5.0 miles (8.0 km). As the vehicle begins moving,
the display will increase to 5.1 miles (8.2 km),
5.2 miles (8.4 km), etc.
If the retro-active reset feature is activated after
the vehicle is started, but before it begins moving,
the display will show the number of miles or
kilometers that were driven during the last ignition
cycle.
Press the trip odometer button again to access the
odometer.
187