2007 PONTIAC GRAND PRIX lock

Defogging and Defrosting
Fog on the inside of the vehicle is a result of high
humidity causing moisture to condense on the cool
window glass. This can be minimized if the climate
control system is used properly. There are
two modes to clear frost or fog from the windshield.
Use the defog mode to clear the windows of
condensation and to warm the vehicle’s occupants.
Use the defrost mode to remove frost or
condensation from the windshield quickly.
See “Rear Window Defogger” later in this section
for information on clearing the rear window of
fog or ice.
.(Floor/Defog):Use the oor/defog mode to
clear the windows of fog or moisture and to
warm the passengers. This mode directs the air
equally between the windshield and the oor
outlets, along with some directed to the side
window outlets.
This mode will automatically use outside air. The
air conditioning compressor will be engaged
unless the outside temperature is 40°F (4°C) or
below. Recirculation cannot be selected when
in this mode even though the indicator light comes
on when the recirculation button is pressed.
1(Defrost):Use the defrost mode to remove
fog or frost from the windshield more quickly. This
mode directs most of the air to the windshield
and the side window outlets, with some air directed
to the oor outlets. This mode has a timer and
will shut off after ve minutes.
This mode will automatically use outside air. The
air conditioning compressor will be engaged
unless the outside temperature is 40°F (4°C) or
below. Recirculation cannot be selected when
in this mode even though the indicator light comes
on when the recirculation button is pressed.
Temperature
The knob on the right of the climate control panel
is the temperature adjustment that can be used
with any of the climate control modes.
Turn the knob clockwise for warmer settings and
counterclockwise for colder settings.
159

Do not cover the solar sensor located in the
center of the instrument panel, near the
windshield. For more information on the solar
sensor, see “Sensors” later in this section.
Manual Operation
xw
(Temperature):To manually adjust the
temperature inside the vehicle, press the up arrow
on the temperature control to raise the temperature
and press the down arrow to lower the
temperature. The display will show your selection.
When one temperature is displayed, the driver
temperature is set. When both temperatures are
displayed, the temperature for both the driver
and passenger are set. Pressing PASS will turn
the passenger temperature setting on and
off. If only the driver temperature is set, the driver
temperature is used for the passenger and the
passenger display is off.
9(Fan):Turn the fan knob clockwise to increase
the fan speed and counterclockwise to decrease
the fan speed. Turning the fan knob cancels
the automatic fan operation and places the systemin manual. Turn the knob to AUTO to return to
automatic fan operation. If the airow seems low
when the fan is at the highest setting, the
passenger compartment air lter, if equipped, may
need to be replaced. SeePassenger Compartment
Air Filter on page 166for additional information.
9(Off):Turning the fan knob off will turn
the controller completely off.
Mode:This control has several settings to control
the direction of airow.
To change the current mode, select one of the
following:
AUTO:This mode is automatically set depending
on the temperature in the vehicle and solar
sensor information.
H(Vent):This mode directs air to the
instrument panel outlets.
%(Bi-Level):This mode directs airow to the
instrument panel outlets and to the oor outlets.
A small amount of air is also directed to the
windshield and the side window outlets.
163

Outlet Adjustment
Turn the air outlets, located in the middle and at
each outboard side of the instrument panel,
to adjust the direction of the airow.
Operation Tips

Clear away any ice, snow, or leaves from the
air inlets at the base of the windshield that
may block the ow of air into the vehicle.
Use of non-GM approved hood deectors may
adversely affect the performance of the
system.
Keep the path under the front seats clear of
objects to help circulate the air inside of the
vehicle more effectively.
If the airow seems low when the fan is at the
highest setting, the passenger compartment
air lter may need to be replaced. See
“Passenger Compartment Air Filter” following,
for more information.
Passenger Compartment Air Filter
The passenger compartment air lter is located
near the passenger’s side windshield wiper
arm, under the inlet grille.
The lter traps most of the pollen from entering
the climate control system. Similar to the engine’s
air lter, it may need to be changed periodically
to insure system performance. SeeScheduled
Maintenance on page 473for more information.
To change the passenger compartment air
lter, do the following:
1. Turn the ignition to ACC and the windshield
wipers on.
2. Turn the ignition to OFF when the windshield
wipers are in the upright position.
3. Raise the hood.
4. Disconnect the windshield washer pump hose
from the fender rail and the air inlet grille.
5. Remove the hood weather-strip from the
passenger’s side of the vehicle, peeling it
back halfway.
166

{CAUTION:
Your brake system may not be working
properly if the brake system warning light
is on. Driving with the brake system
warning light on can lead to an accident.
If the light is still on after you have pulled
off the road and stopped carefully, have
the vehicle towed for service.
Anti-Lock Brake System
Warning Light
If the vehicle has the
Anti-lock Brake System
(ABS), this light will
come on when the
engine is started and
may stay on for several
seconds. That is normal.If the ABS warning light comes on and stays on,
there may be a problem with the anti-lock
portion of the brake system. If the brake system
warning light is not on, the vehicle still has brakes,
but it does not have anti-lock brakes. SeeBrake
System Warning Light on page 176.
If the light stays on, the vehicle needs service.
If the light comes on while the vehicle is being
driven, stop as soon as possible and turn the
ignition off. Then start the vehicle again to reset the
system. If the light still stays on, or comes on again
while driving, the vehicle needs service. If the
regular brake system warning light is not on, the
vehicle still has brakes, but it does not have
anti-lock brakes. If the brake system warning light is
also on, the vehicle does not have anti-lock brakes
and there is a problem with the regular brakes. See
Brake System Warning Light on page 176. If both
the brake system warning light and the anti-lock
brake system light is on, pull off the road and have
the vehicle towed for service.
The anti-lock brake system warning light will come
on briey when the ignition key is turned to
RUN. This is normal. If the light does not come on
then, have it xed so it will be ready to warn
you if there is a problem.
177

This message and symbol display briey whenever
the cruise control is set. The cruise control light
on the instrument panel cluster also comes
on when cruise control is set. SeeCruise Control
Light on page 185. CRUISE SET also appears
briey in the Head-Up Display (HUD), if your
vehicle has this feature. This message displays
when the ignition is in RUN. SeeCruise Control on
page 140for more information.
This message does not need to be acknowledged.
DELAYED LOCKING
This message displays when the doors of the
vehicle are closed and the delayed locking feature
has been programmed through the DIC. See
“DELAYED LOCKING” underDIC Vehicle
Customization on page 226for more information.
This message displays when the ignition is in
OFF. A chime sounds for two seconds when this
message is displayed.
This message cannot be acknowledged.
HEADLAMPS SUGGESTED
This message displays when the amount of
available light outside the vehicle is low and the
exterior lamps control has been turned off. This
condition happens when the headlamps are turned
off at night or the Daytime Running Lamps (DRL)
are turned off during the day. This message informs
the driver that it has become dark enough outside
to require the headlamps to be turned on. When the
headlamps are turned on, this message clears from
the screen. SeeExterior Lamps on page 144and
Daytime Running Lamps (DRL) on page 145for
more information.
This message displays while the ignition is in
RUN. A chime sounds for two seconds when this
message is displayed. Press the set/reset
button to acknowledge this warning message and
to clear it from the screen.
This message continues to display if it has not
been acknowledged when the engine is turned off.
It also re-displays for three seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message
re-appears when the engine is turned on.
205

SERVICE ABS SYSTEM
This symbol comes on
with this message.
If the vehicle has the Anti-lock Brake System (ABS),
this message displays when the vehicle’s brakes
are not functioning properly. Have the brake system
serviced by your dealer as soon as possible.
This message displays only while the ignition is in
RUN. A chime sounds for two seconds while
this message is displayed. Press the set/reset
button to acknowledge this message and to clear
it from the screen.
This message continues to display if it has not
been acknowledged when the engine is turned off.
It also re-displays for three seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message
re-appears when the engine is turned on.
SERVICE BRAKE SYSTEM
This symbol comes on
with this message.
This message displays when the vehicle’s brakes
are not functioning properly. Have the brake
system serviced by your dealer as soon as
possible.
This message displays only while the ignition is in
RUN. A chime sounds for two seconds while
this message is displayed. Press the set/reset
button to acknowledge this message and to clear
it from the screen.
This message continues to display if it has not
been acknowledged when the engine is turned off.
It also re-displays for three seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message
re-appears when the engine is turned on.
217

Entering the Personal Programming Mode
1. Turn the ignition on and make sure the
vehicle is in PARK (P).
To avoid excessive drain on the battery, it is
recommended that the headlamps are
turned off.
2. Press the options button until PERSONAL
PROGRAMMING MODE appears on the DIC.
3. Press the set/reset button to display the rst
screen.
4. Press the options button to access these
modes:
Personal Programming Mode Screens
EXTERIOR LIGHTING DELAY:This screen
allows this feature to be turned off, or allows the
selection of the number of seconds the headlamps,
sidelamps, taillamps, fog lamps, and back-up
lamps are turned on after the key is removed from
the ignition, or the vehicle is unlocked using the
remote keyless entry transmitter.
If OFF is selected, the exterior lamps will not
turn on.If a time delay is chosen, the lamps will turn on for
the selected time. The time delay will be
cancelled and the exterior lamps will turn on
automatically when the key is removed from the
ignition, or the vehicle is unlocked using the
remote keyless entry transmitter.
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to the selection you want to program.
Choose from OFF, 15, 30, 60, or 90 seconds.
2. Press the options button again to advance to
the next screen.
INTERIOR LIGHTS WHEN DOOR CLOSED:This
screen allows this feature to be turned OFF or ON.
If OFF is selected, the interior lamps will turn off
immediately when the ignition is turned off and the
last open door is closed.
If ON is selected, the interior lamps will stay on for
about 25 seconds after the vehicle’s ignition is
turned off and the last open door is closed.
227

To program this mode, use the following procedure:
1. Press and release the set/reset button to
scroll to either OFF or ON.
2. Press the options button again to advance to
the next screen.
INTERIOR LIGHTS WHEN KEY REMOVED:This
screen allows this feature to be turned OFF or
ON. This feature enables the interior lamps in the
vehicle to turn on for about 25 seconds after
the key is removed from the ignition.
If OFF is selected, removing the key from the
ignition will not cause the interior lamps to turn on.
If ON is selected, removing the key from the
ignition will cause the interior lamps to be turned
on for about 25 seconds.
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to either OFF or ON.
2. Press the options button again to advance to
the next screen.AUTO DOOR UNLOCK:This screen allows this
feature to be turned off, used for the driver’s
door only, or for all the doors.
If OFF is selected, none of the doors will unlock
when the vehicle’s transaxle is shifted into
PARK (P).
If DRIVER is selected, only the driver’s door will
unlock when the vehicle’s transaxle is shifted
into PARK (P).
If ALL is selected, all the doors will unlock when
the vehicle’s transaxle is shifted into PARK (P).
To program this mode, use the following
procedure:
1. Press and release the set/reset button to
scroll to either OFF, DRIVER, or ALL.
2. Press the options button again to advance to
the next screen.
228