2007 PONTIAC GRAND PRIX instrument cluster

The CRUISE SET message will also appear
briey on the Head-Up Display (HUD), if your
vehicle has one, when the cruise control lever is
pushed to the minus (set) or the plus
(resume/accelerate) positions.
A cruise control light will also appear on the
instrument panel cluster when the cruise control is
on. This light will disappear when the brakes
are applied or the cruise control is cancelled. It will
reappear when the set cruise speed is resumed.
The light will go out when the cruise control is
turned off. SeeCruise Control Light on page 185.
Resuming a Set Speed
Once you are going about 25 mph (40 km/h) or
more, you can move the cruise control switch
briey from on to resume/accelerate.
Your vehicle will go back up to your previously
chosen speed and stay there.
If you hold the switch at resume/accelerate the
vehicle will keep going faster until you release the
switch or apply the brake. Do not hold the
switch at resume/accelerate, unless you want the
vehicle to go faster.
Increasing Speed While Using
Cruise Control
There are two ways to go to a higher speed:
Use the accelerator pedal to get to the higher
speed. Press the set button at the end of the
lever, then release the button and the
accelerator pedal. You will now cruise at the
higher speed. If the accelerator pedal is
held longer than 60 seconds, cruise control
will turn off.
Move the cruise switch from on to resume/
accelerate. Hold it there until you get up to the
speed desired, and then release the switch.
To increase the vehicle speed in very small
amounts, move the switch briey to resume/
accelerate. Each time you do this, your vehicle
will go about 1 mph (1.6 km/h) faster.
The acceleration feature will only work after the
cruise control speed has been set by pushing the
cruise control set button.
142

Headlamps on Reminder
A warning chime will sound if the vehicle’s ignition
is off and the driver’s door is opened when the
exterior lamp control is left on in either the
headlamp or parking lamp position.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during
the day. DRL can be helpful in many different
driving conditions, but they can be especially
helpful in the short periods after dawn and before
sunset. Daytime running lamps are required to
function at all times on all vehicles rst sold
in Canada.
A light sensor on top of the instrument panel
makes the DRL work, so be sure it is not covered.
The DRL system will make the low-beam
headlamps come on at reduced brightness when
the following conditions are met:
The ignition is on.
The exterior lamps control is off.
The parking brake is released.While the DRL are on, only the vehicle’s low-beam
headlamps will be on at reduced brightness.
The turn signal, taillamps, sidemarker and other
lamps will not be on. The instrument panel cluster
will not be lit up either.
When it is dark enough outside, the DRL will turn
off and the vehicle’s headlamps and parking
lamps will turn on. The other lamps that come on
with the headlamps will also come on.
When it is bright enough outside, the headlamps
will go off and the DRL will come on.
To idle the vehicle with the DRL off, turn the
exterior lamp control off and then do one of the
following:
Turn the exterior lamp control to the parking
lamp position.
Turn the exterior lamp control to the headlamp
position.
Turn the exterior lamp control from AUTO to
off and back to AUTO.
This feature is not available for vehicles rst sold
in Canada.
145

To turn off the automatic headlamp feature when it
is dark outside, move the exterior lamp control
to the parking lamp position. The parking lamps
will remain illuminated and the headlamps will turn
off. The fog lamps will also go on if they were
on previously.
As with any vehicle, the regular headlamp system
should be turned on when needed.
Fog Lamps
If equipped, fog lamps provide brighter roadway
lighting for better vision in foggy or misty
conditions.
-(Fog Lamps):Turn the second band on the
exterior lamps control lever to this position to
turn the fog lamps on. The band will return to its
original position.
This symbol appears on
the instrument panel
cluster when the
fog lamps are on.To turn the fog lamps off, turn the band up to the
fog lamp symbol and release it. The band will
return to its original position. If the high-beam
headlamps are on, the fog lamps will turn off. The
fog lamps will go on again when the low-beam
headlamps are turned back on.
The parking lamps must be on for the fog lamps
to work.
Some localities have laws that require the
headlamps to be on along with the fog lamps.
Exterior Lighting Battery Saver
If the parking lamps or headlamps have been left
on after the ignition has been turned to off, the
exterior lamps will turn off after about 10 minutes.
This protects the battery from being drained.
Use the exterior lamp control to turn the lamps
back on, if they are still needed.
Interior Lamps
The interior lamps can be controlled, or
automatically turn on or off under certain conditions.
They are explained in the following text.
146

I II III IIII (Brightness):Turn the outer ring on the
HUD control clockwise to dim the display and
counterclockwise to brighten it.
w(Up):Press this portion of the switch on the
HUD control to move the image up.
x(Down):Press this portion of the switch on
the HUD control to move the image down.
Move the image as low as possible on the
windshield, keeping it in full view.
?(Page):Press this button to select the display
formats. Release the page button when the
format number with the desired display is shown
on the HUD.
Format One:This display gives the
speedometer reading (in English or metric
units), transaxle positions, compass direction,
and the outside air temperature.
Format Two:This display includes the
information in Format One without the compass
direction and the outside air temperature.
Format Three:This display includes all the
information in Format One, but turns the
instrument cluster lighting off. Format three is
only available at night.
All formats will show the turn-by-turn guidance
information. It will display the next turn, direction,
street name, and distance to the selected
destination. When you near your destination, the
HUD will display a distance bar that will ll in
the closer you get to your destination. All
navigation information is provided to the HUD by
the navigation radio, if the vehicle has one.
The warning indicators still appear on the
instrument panel when required. The HUD will
display Stealth Mode On.
The HUD will store the last display format selected.
If the last format displayed was Format One or
Format Three, then Format One will be displayed
when the vehicle is started.
If the last format was Format Two, then Format
Two will be displayed.
154

Instrument Panel Cluster
The instrument panel cluster is designed to show at a glance how the vehicle is running. It will show how
fast the vehicle is going, about how much fuel is in the fuel tank, and many other things needed to
drive the vehicle safely and economically.
United States version shown, Canada similar
169

Passenger Safety Belt
Reminder Light
Several seconds after the key is turned to RUN or
START, a chime will sound for several seconds to
remind the front passenger to buckle their safety
belt. This would only occur if the passenger airbag
is enabled. SeePassenger Sensing System on
page 74for more information. The passenger
safety belt light will also come on and stay on for
several seconds, then it will ash for several more.
If the passenger’s safety
belt is buckled, neither
the chime nor the
light will come on.
Airbag Readiness Light
There is an airbag readiness light on the
instrument panel cluster, which shows the airbag
symbol. The system checks the airbag’s
electrical system for malfunctions. The light
indicates if there is an electrical problem. The
system check includes the airbag sensors,
the airbag modules, the wiring, and the diagnostic
module. For more information on the airbag
system, seeAirbag System on page 64.
This light will come on
when the vehicle is
started, and it will ash
for a few seconds. Then
the light should go out.
This means the system is functioning properly.
If the airbag readiness light stays on after the
vehicle is started, or comes on as the vehicle is
being driven, the airbag system may not work
properly. Have the vehicle serviced right away.
172

To change the language, use the following
procedure:
1. Press the options button to enter the language
screen.
2. Press the set/reset button to scroll through
and set the language choice.
3. Press the options button again to advance to
the next screen.
DISPLAY UNITS:This menu allows selection of
measurements to be displayed in English or
metric units. The messages on the HUD, if
equipped, and the instrument panel cluster will
also appear with the type of measurement
selected.
To set the measurement when Display Units is
shown, use the following procedure:
1. Press the set/reset button to select ENGLISH
or METRIC.
2. Press the options button again to advance to
the next screen.DAYTIME DISPLAY ENHANCEMENT:This
menu allows selection of the color of the display
message. When ON is selected for the daytime
enhancement, the messages will appear black on
a red screen. This combination makes it easier
to see the DIC messages during the daytime.
When OFF is selected, or when the headlamps
are on, the messages will appear red on a
black background.
To set the daytime display enhancement, use the
following procedure:
1. Press the set/reset button to select OFF or ON.
2. Press the options button again to advance to
the next screen.
ENGINE OIL MONITOR SYSTEM:This menu
allows the engine oil monitor system to be reset.
To reset the engine oil monitor system, see
Engine Oil Life System on page 353.
PERSONAL PROGRAMMING MODE:This menu
allows you to customize several features on
your vehicle. SeeDIC Vehicle Customization on
page 226for more information.
Press the options button again to advance to the
next screen.
189

3. Press the options button to advance to the
rst position in the year. Press and hold the
set/reset button to scroll through the available
digits. Release the button when the correct
digit appears.
4. Press the options button to advance to the
months of the year.
5. Press the set/reset button to scroll through the
months of the year, releasing the button when
the correct month appears.
6. Press the options button to advance to the
days of the month.
7. Press the set/reset button to scroll through the
days of the month, releasing the button when
the correct day appears.
8. Press the options button again to advance to
the main date screen. The screen will now
display the new date.
9. Press the options button to advance to the
next screen.Language:This menu allows selection of
the language in which the DIC messages will
appear. The DIC can be programmed in one of
three languages: English, French, or Spanish. The
message on the HUD, if equipped, will also
appear in the language selected. SeeHead-Up
Display (HUD) on page 151.
To change the language, use the following
procedure:
1. Press the options button to enter the language
screen.
2. Press the set/reset button to scroll through
and set the language choice.
3. Press the options button again to advance to
the next screen.
DISPLAY UNITS:This menu allows selection of
measurements to be displayed in English or
metric units. The messages on the HUD, if
equipped, and the instrument panel cluster will
also appear in the type of measurement selected.
195