2007 NISSAN TIIDA display

AV
U1243 DISPLAY UNIT
AV-77
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Is inspection result OK?
YES >> GO TO 4
NO >> Replace NAVI control unit.
4.CHECK COMMUNICATION SIGNAL
Check signal between display unit harness connector terminal 19 and ground.
Is inspection result OK?
YES >> INSPECTION END.
NO >> Replace display unit.
17 - Ground
PKIB5039J
19 - Ground
PKIB5039J

AV-78
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
U1244 GPS ANTENNA
U1244 GPS ANTENNA
DescriptionINFOID:0000000001728716
DTC LogicINFOID:0000000001728717
Diagnosis ProcedureINFOID:0000000001728718
1.CHECK GPS ANTENNA
Visually check GPS antenna and antenna feeder.
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair malfunctioning parts.
2.CHECK NAVI CONTROL UNIT VOLTAGE
1. Disconnect GPS antenna connector.
2. Turn ignition switch ON.
3. Check voltage between NAVI control unit terminal 73 and ground.
Is inspection result OK?
YES >> INSPECTION END
NO >> Replace NAVI control unit.
Part name Description
GPS ANTENNA GPS signal is received and sent to NAVI control unit.
DTCDisplay contents of
CONSULT-IIIDTC Detection Condition Possible causes
U1244GPS ANTENNA CONN
[U1244]GPS antenna connection malfunction is detected. GPS antenna disconnection
73 - Ground : Approx. 5 V

AV
U1300 AV COMM CIRCUIT
AV-79
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
U1300 AV COMM CIRCUIT
DescriptionINFOID:0000000001728722
U1300 is indicated when malfunction occurs in communication signal of multi AV system. It is indicated simul-
taneously, without fail, with the malfunction of control units connected to NAVI control unit with communication
line. It determines the possible malfunction cause from the table below.
SELF-DIAGNOSIS RESULTS DISPLAY ITEM
DTCDisplay contents of
CONSULT-IIIDescriptionPossible malfunction factor/Action to
take
U1300
U1240
U1249
U124E
U124F AV COMM CIRCUIT
[U1300]
 SWITCH CONN
[U1240]
 AUDIO H/U CONN
[U1249]
 AMP CONN [U124E]
 RDS CONN [U124F] Audio unit power supply and ground circuit malfunction
is detected.
 Malfunction occurs in AV communication circuit be-
tween NAVI control unit and audio unit.
 Malfunction is detected in AV communication signal be-
tween NAVI control unit and audio unit. Audio unit power supply and
ground circuits
Refer to AV- 8 0 , "
AV CONTROL
UNIT : Diagnosis Procedure".
 AV communication circuit between
NAVI control unit and audio unit

AV
POWER SUPPLY AND GROUND CIRCUIT
AV-81
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Is inspection result OK?
YES >> GO TO 3
NO >> Check harness between NAVI control unit and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connectors.
3. Check continuity between NAVI control unit harness connector and ground.
Is inspection result OK?
YES >> INSPECTION END.
NO >> Repair harness or connector.
DISPLAY UNIT
DISPLAY UNIT : Diagnosis ProcedureINFOID:0000000001728725
1.CHECK FUSE
Check for blown fuses.
Is inspection result OK?
YES >> GO TO 2
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between display unit harness connectors and ground.
Is inspection result OK?
YES >> GO TO 3
NO >> Check harness between display unit and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector.
3. Check continuity between display unit harness connector and ground.
Is inspection result OK?
YES >> INSPECTION END.
NO >> Repair harness or connector.
Signal name Connector No. Terminal No. Ignition switch position Value (Approx.)
Battery power supply B69 2 OFF 12V
ACC power supply B69 5 ACC 12V
Ignition signal B68 63 ON 12V
Signal name Connector No. Terminal No. Ignition switch position Continuity
Ground B69 1 OFF Continuity should exist.
Power source Fuse No.
Battery 27
Ignition switch ACC or ON 6
Signal name Connector No. Terminal No. Ignition switch position Value (Approx.)
Battery power supply M100 21 OFF 12V
ACC power supply M100 20 ACC 12V
Signal name Connector No. Terminal No. Ignition switch position Continuity
Ground M100 23 OFF Continuity should exist.

AV-82
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
RGB (R: RED) SIGNAL CIRCUIT
RGB (R: RED) SIGNAL CIRCUIT
DescriptionINFOID:0000000001728727
Transmits the image displayed with NAVI control unit with RGB signal to the display unit.
Diagnosis ProcedureINFOID:0000000001728728
1.CHECK CONTINUITY RGB (R: RED) SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and NAVI control unit connector.
3. Check continuity between display unit harness connector terminal 1 and NAVI control unit harness con-
nector terminal 44.
4. Check continuity between display unit harness connector terminal 1 and ground.
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK RGB (R: RED) SIGNAL
1. Connect display unit connector and NAVI control unit connector.
2. Turn ignition switch ON.
3. Start “Confirmation / Adjustment Mode”, and then display color bar by selecting“Color Spectrum Bar” on
DISPLAY DIAGNOSIS screen.
4. Check signal between display unit harness connector terminal 1 and 8.
Is inspection result OK?
YES >> Replace display unit.
NO >> Replace NAVI control unit.1 - 44 : Continuity should exist.
1 - Ground : Continuity should not exist.
1 - 8
JPNIA0221ZZ

AV
RGB (G: GREEN) SIGNAL CIRCUIT
AV-83
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
RGB (G: GREEN) SIGNAL CIRCUIT
DescriptionINFOID:0000000001728729
Transmits the image displayed with NAVI control unit with RGB signal to the display unit.
Diagnosis ProcedureINFOID:0000000001728730
1.CHECK CONTINUITY RGB (G: GREEN) SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and NAVI control unit connector.
3. Check continuity between display unit harness connector terminal 3 and NAVI control unit harness con-
nector terminal 45.
4. Check continuity between display unit harness connector terminal 3 and ground.
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK RGB (G: GREEN) SIGNAL
1. Connect display unit connector and NAVI control unit connector.
2. Turn ignition switch ON.
3. Start “Confirmation / Adjustment Mode”, and then display color bar by selecting“Color Spectrum Bar” on
DISPLAY DIAGNOSIS screen.
4. Check signal between display unit harness connector terminal 3 and 8.
Is inspection result OK?
YES >> Replace display unit.
NO >> Replace NAVI control unit.3 - 45 : Continuity should exist.
3 - Ground : Continuity should not exist.
3 - 8
JPNIA0222ZZ

AV-84
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
RGB (B: BLUE) SIGNAL CIRCUIT
RGB (B: BLUE) SIGNAL CIRCUIT
DescriptionINFOID:0000000001728731
Transmits the image displayed with NAVI control unit with RGB signal to the display unit.
Diagnosis ProcedureINFOID:0000000001728732
1.CHECK CONTINUITY RGB (B: BLUE) SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and NAVI control unit connector.
3. Check continuity between display unit harness connector terminal 5 and NAVI control unit harness con-
nector terminal 46.
4. Check continuity between display unit harness connector terminal 5 and ground.
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK RGB (B: BLUE) SIGNAL
1. Connect display unit connector and NAVI control unit connector.
2. Turn ignition switch ON.
3. Start “Confirmation / Adjustment Mode”, and then display color bar by selecting“Color Spectrum Bar” on
DISPLAY DIAGNOSIS screen.
4. Check signal between display unit harness connector terminal 5 and 8.
Is inspection result OK?
YES >> Replace display unit.
NO >> Replace NAVI control unit.5 - 46 : Continuity should exist.
5 - Ground : Continuity should not exist.
5 - 8
JPNIA0223ZZ

AV
RGB SYNCHRONIZING SIGNAL CIRCUIT
AV-85
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
RGB SYNCHRONIZING SIGNAL CIRCUIT
DescriptionINFOID:0000000001728733
Transmits the RGB synchronizing signal to the display unit so as to synchronize the RGB image displayed
with NAVI control unit.
Diagnosis ProcedureINFOID:0000000001728734
1.CHECK CONTINUITY RGB SYNCHRONIZING SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display unit connector and NAVI control unit connector.
3. Check continuity between display unit harness connector terminal 7 and NAVI control unit harness con-
nector terminal 48.
4. Check continuity between display unit harness connector terminal 7 and ground.
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK RGB SYNCHRONIZING SIGNAL
1. Connect display unit connector and NAVI control unit connector.
2. Turn ignition switch ON.
3. Check signal between display unit harness connector terminal 7 and ground.
Is inspection result OK?
YES >> Replace display unit.
NO >> Replace NAVI control unit.7 - 48 : Continuity should exist.
7 - Ground : Continuity should not exist.
7 - Ground
SKIB0825E