2007 NISSAN TIIDA wiring

BRC-182
< REMOVAL AND INSTALLATION >[ESP/TCS/ABS]
WHEEL SENSORS
REMOVAL AND INSTALLATION
WHEEL SENSORS
Removal and InstallationINFOID:0000000001691451
REMOVAL
Be careful of the following.
CAUTION:
 When removing the sensor, do not rotate it if possible, and not forcibly pull the sensor harness.
 Before removing front or rear wheel hub, remove wheel sensor to avoid sensor wiring damage.
INSTALLATION
Be certain to tighten bolts to the specified torque. Be careful of the following: Check the inside of the sensor mounting hole for foreign material, the rotor surface for iron chips and other
foreign material, and if anything is non-standard, clean it before installation, or replace it.
 When installing the front sensor, completely push in the strut bracket and body bracket rubber grommets
until they lock so that the sensor harness does not become twisted. In addition, there should be no twists in
the harness when installed. Install the harness so that the painted part faces the outside of the vehicle.
 When installing the rear sensor, completely push in the rubber bracket of the suspension arm bracket and
lock the marking area of the side member harness mount so that the sensor harness will not be twisted. In
addition, there should be no twists in the harness when installed.
MFIB9030E

CHG
CHG-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L B
SECTION CHG
A
O
P N
CONTENTS
CHARGING SYSTEM
HR16DE
PRECAUTION ...............................................
3
PRECAUTIONS ...................................................3
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................
3
PREPARATION ............................................4
PREPARATION ...................................................4
Special Service Tools ................................................4
BASIC INSPECTION ....................................5
DIAGNOSIS AND REPAIR WORKFLOW ..........5
Work Flow .................................................................5
FUNCTION DIAGNOSIS ...............................8
CHARGING SYSTEM ..........................................8
System Diagram ........................................................8
System Description ...................................................8
Component Description ............................................8
COMPONENT DIAGNOSIS ..........................9
CHARGING SYSTEM PRELIMINARY IN-
SPECTION ...........................................................
9
Inspection Procedure ................................................9
B TERMINAL CIRCUIT ......................................10
Description ..............................................................10
Diagnosis Procedure ...............................................10
L TERMINAL CIRCUIT .......................................11
Description ..............................................................11
Diagnosis Procedure ...............................................11
S TERMINAL CIRCUIT ......................................12
Description ..............................................................12
Diagnosis Procedure ...............................................12
CHARGING SYSTEM .......................................13
Wiring Diagram ........................................................13
SYMPTOM DIAGNOSIS ..............................14
CHARGING SYSTEM .......................................14
Symptom Table .......................................................14
ON-VEHICLE REPAIR .................................15
GENERATOR ....................................................15
Removal and Installation .........................................15
SERVICE DATA AND SPECIFICATIONS
(SDS) ............................................................
16
SERVICE DATA AND SPECIFICATIONS
(SDS) .................................................................
16
Generator ................................................................16
MR18DE
PRECAUTION ..............................................
17
PRECAUTIONS .................................................17
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................
17
PREPARATION ...........................................18
PREPARATION .................................................18
Special Service Tools ..............................................18
BASIC INSPECTION ...................................19
DIAGNOSIS AND REPAIR WORKFLOW ........19
Work Flow ................................................................19
FUNCTION DIAGNOSIS ..............................22
CHARGING SYSTEM .......................................22
System Diagram ......................................................22
System Description ..................................................22

CHG-2
Component Description .........................................22
COMPONENT DIAGNOSIS ........................23
CHARGING SYSTEM PRELIMINARY IN-
SPECTION .........................................................
23
Inspection Procedure ..............................................23
B TERMINAL CIRCUIT ......................................24
Description ..............................................................24
Diagnosis Procedure ..............................................24
L TERMINAL CIRCUIT ......................................25
Description ..............................................................25
Diagnosis Procedure ..............................................25
S TERMINAL CIRCUIT ......................................26
Description ..............................................................26
Diagnosis Procedure ..............................................26
CHARGING SYSTEM ........................................27
Wiring Diagram .......................................................27
SYMPTOM DIAGNOSIS .............................28
CHARGING SYSTEM ........................................28
Symptom Table ......................................................28
ON-VEHICLE REPAIR ................................29
GENERATOR ....................................................29
Removal and Installation ........................................29
SERVICE DATA AND SPECIFICATIONS
(SDS) ...........................................................
30
SERVICE DATA AND SPECIFICATIONS
(SDS) ..................................................................
30
Generator ...............................................................30
K9K
PRECAUTION .............................................
31
PRECAUTIONS .................................................31
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................
31
PREPARATION ...........................................32
PREPARATION .................................................32
Special Service Tools .............................................32
BASIC INSPECTION ..................................33
DIAGNOSIS AND REPAIR WORKFLOW .........33
Work Flow ...............................................................33
FUNCTION DIAGNOSIS ............................36
CHARGING SYSTEM ........................................36
System Diagram .....................................................36
System Description .................................................36
Component Description ..........................................36
COMPONENT DIAGNOSIS .......................37
CHARGING SYSTEM PRELIMINARY IN-
SPECTION .........................................................
37
Inspection Procedure ..............................................37
B TERMINAL CIRCUIT .....................................38
Description ..............................................................38
Diagnosis Procedure ...............................................38
L TERMINAL CIRCUIT ......................................39
Description ..............................................................39
Diagnosis Procedure ...............................................39
S TERMINAL CIRCUIT ......................................40
Description ..............................................................40
Diagnosis Procedure ...............................................40
CHARGING SYSTEM ........................................41
Wiring Diagram .......................................................41
SYMPTOM DIAGNOSIS ............................42
CHARGING SYSTEM ........................................42
Symptom Table .......................................................42
ON-VEHICLE REPAIR ...............................43
GENERATOR ....................................................43
Removal and Installation .........................................43
SERVICE DATA AND SPECIFICATIONS
(SDS) ..........................................................
44
SERVICE DATA AND SPECIFICATIONS
(SDS) .................................................................
44
Generator ................................................................44

CHG
PRECAUTIONS
CHG-3
< PRECAUTION >[HR16DE]
C
D
E
F
G
H
I
J
K
L B A
O
P N
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001731367
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
 Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
 Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

CHG
CHARGING SYSTEM
CHG-13
< COMPONENT DIAGNOSIS >[HR16DE]
C
D
E
F
G
H
I
J
K
L B A
O
P N
CHARGING SYSTEM
Wiring DiagramINFOID:0000000001724481
AWMWA0022GB

CHG
PRECAUTIONS
CHG-17
< PRECAUTION >[MR18DE]
C
D
E
F
G
H
I
J
K
L B A
O
P N
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001731368
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
 To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
 Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
 Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

CHG
CHARGING SYSTEM
CHG-27
< COMPONENT DIAGNOSIS >[MR18DE]
C
D
E
F
G
H
I
J
K
L B A
O
P N
CHARGING SYSTEM
Wiring DiagramINFOID:0000000001724532
ALMWA0073GB

CHG
PRECAUTIONS
CHG-31
< PRECAUTION >[K9K]
C
D
E
F
G
H
I
J
K
L B A
O
P N
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001731369
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
 To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
 Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
 Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.