2007 NISSAN TIIDA reverse light

SHIFT CONTROL SYSTEM
TM-203
< ON-VEHICLE REPAIR >[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
 When installing the control cable (1) to the control device assembly
(2), make sure that the control cable (1) is fully pressed in with the
ribbed surface (A) facing downward from the vehicle.
: Vehicle front
 After installation is completed, adjust and check the A/T position.
Refer to TM-204, "
Adjustment of A/T Position" and TM-204,
"Checking of A/T Position".
Control Device Disassembly and AssemblyINFOID:0000000001731376
DISASSEMBLY
NOTE:
Refer to TM-200, "
Control Device Removal and Installation" to disassemble.
1. Remove selector lever knob from control device assembly. Refer to TM-203, "
Selector Lever Knob
Removal and Installation".
2. Remove position lamp from position indicator plate (1).
3. Insert a flat-bladed screwdriver to (A) (at 4 locations) as shown,
and bend each hook slightly to raise position indicator plate (1)
and remove from control device assembly (2).
4. Remove bracket from control device assembly (2).
5. Remove A/T device harness connector from control device
assembly (2).
6. Release tabs (A) on shift lock solenoid and park position switch
assembly from hooks (B) on control device assembly to shift
lock solenoid and park position switch assembly.
ASSEMBLY
Assemble in the reverse order of disassembly.
Selector Lever Knob Removal and InstallationINFOID:0000000001731377
REMOVAL
CAUTION:
Make sure that parking brake is applied before removal/installation.
SCIA6253E
SCIA6969E
SCIA6977E

TM-262
< DISASSEMBLY AND ASSEMBLY >[TYPE 1 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
NOTE:
Install two dish plates fitting each installation direction with
reverse clutch drum groove displaced slightly.
6. Install snap ring (1) using suitable tool (A).
7. Measure clearance between retaining plate and snap ring using
feeler gauge. If not within allowable limit, select proper retaining
plate.
8. Check operation of reverse clutch. Refer to TM-258, "
Reverse
Clutch".
High ClutchINFOID:0000000001730989
COMPONENTS
SAT170D
SCIA7024J
Specified clearance
Standard and allowable limit:
Refer to TM-321, "
Clutches and Brakes".
SAT174D
SCIA6741E

REPAIR FOR COMPONENT PARTS
TM-277
< DISASSEMBLY AND ASSEMBLY >[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
3. Install spring retainer assembly (1) on low & reverse brake pis-
ton (2).
4. Set Tool on spring retainer assembly, and install snap ring while
compressing spring retainer assembly.
CAUTION:
Set Tool directly over return springs.
5. Install driven plates (4), dish plates (6), retaining plates (2), (5)
and drive plates (3).
(1): Snap ring
(2): Retaining plate
(3): Drive plate
(4): Driven plate
(5): Retaining plate
(6): Dish plate
Drive plate/Driven plate: 4/4
CAUTION:
Be careful with the order of plates
NOTE:
Install two dish plates fitting each installation direction with
groove (1) and (2) displaced slightly.
SCIA6020J
SAT242D
SCIA5994E
SAT254E

SHIFT CONTROL SYSTEM
TM-495
< ON-VEHICLE REPAIR >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
7. Remove the plate (1) from the control device assembly.
: Vehicle front
8. Remove the lock plate (1) from the control cable (2).
: Vehicle front
9. Remove the control cable (2) from the control device assembly.
10. Insert flat-bladed screwdrivers at points (A) and (B) as shown,
and press both tabs (E) and (F) at the front (C) and rear (D)
slightly toward the center of the control device assembly to
remove the control device assembly from the underside of the
vehicle.
: Vehicle front
INSTALLATION
Installation is in the reverse order of removal.
SCIA6967E
SCIA6968E
SCIA6970E

TM-496
< ON-VEHICLE REPAIR >[TYPE 2 (4AT: RE4F03B)]
SHIFT CONTROL SYSTEM
 When installing the control cable (1) to the control device assembly
(2), make sure that the control cable (1) is fully pressed in with the
ribbed surface (A) facing downward from the vehicle.
: Vehicle front
 After installation is completed, adjust and check the A/T position.
Refer to TM-497, "
Adjustment of A/T Position" and TM-497,
"Checking of A/T Position".
Control Device Disassembly and AssemblyINFOID:0000000001731422
DISASSEMBLY
NOTE:
Refer to TM-493, "
Control Device Removal and Installation" to disassemble.
1. Remove selector lever knob from control device assembly. Refer to TM-496, "
Selector Lever Knob
Removal and Installation".
2. Remove position lamp from position indicator plate (1).
3. Insert a flat-bladed screwdriver to (A) (at 4 locations) as shown,
and bend each hook slightly to raise position indicator plate (1)
and remove from control device assembly (2).
4. Remove bracket from control device assembly (2).
5. Remove A/T device harness connector from control device
assembly (2).
6. Release tabs (A) on shift lock solenoid and park position switch
assembly from hooks (B) on control device assembly to shift
lock solenoid and park position switch assembly.
ASSEMBLY
Assemble in the reverse order of disassembly.
Selector Lever Knob Removal and InstallationINFOID:0000000001731423
REMOVAL
CAUTION:
Make sure that parking brake is applied before removal/installation.
SCIA6253E
SCIA6969E
SCIA6977E

REPAIR FOR COMPONENT PARTS
TM-555
< DISASSEMBLY AND ASSEMBLY >[TYPE 2 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
NOTE:
Install two dish plates fitting each installation direction with
reverse clutch drum groove displaced slightly.
6. Install snap ring (1) using suitable tool (A).
7. Measure clearance between retaining plate and snap ring using
feeler gauge. If not within allowable limit, select proper retaining
plate.
8. Check operation of reverse clutch. Refer to TM-258, "
Reverse
Clutch".
High ClutchINFOID:0000000001731441
COMPONENTS
SAT170D
SCIA7024J
Specified clearance
Standard and allowable limit:
Refer to TM-321, "
Clutches and Brakes".
SAT174D
SCIA6741E

TM-570
< DISASSEMBLY AND ASSEMBLY >[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
3. Install spring retainer assembly (1) on low & reverse brake pis-
ton (2).
4. Set Tool on spring retainer assembly, and install snap ring while
compressing spring retainer assembly.
CAUTION:
Set Tool directly over return springs.
5. Install driven plates (4), dish plates (6), retaining plates (2), (5)
and drive plates (3).
(1): Snap ring
(2): Retaining plate
(3): Drive plate
(4): Driven plate
(5): Retaining plate
(6): Dish plate
Drive plate/Driven plate: 4/4
CAUTION:
Be careful with the order of plates
NOTE:
Install two dish plates fitting each installation direction with
groove (1) and (2) displaced slightly.
SCIA6020J
SAT242D
SCIA5994E
SAT254E

TM-650
< DISASSEMBLY AND ASSEMBLY >[5MT: RS5F91R]
TRANSAXLE ASSEMBLY
27. Shift the shift lever (1) of control shaft assembly to 3rd gear posi-
tion.
NOTE:
 If not, the transaxle case cannot be removed from clutch hous-
ing.
 3rd gear position means that the shift lever of control shaft
assembly is fully rotated clockwise and it is returned approxi-
mately 10°.
28. Install oil gutter to transaxle case.
29. Apply recommended sealant to mating surface of clutch hous-
ing.
CAUTION:
 Remove old sealant adhering to the mating surfaces. Also remove any moisture, oil, or foreign
material adhering to both mating surfaces.
 Check for damage on the mounting surface.
 Apply a continuous bead of liquid gasket to the mounting surface.
30. Install transaxle case to clutch housing.
(1): Selector
(2): Shift fork
CAUTION:
 Do not allow sealant to contact the transaxle case so as
not to break the bead when installing.
 Be careful to align the lever of 5th-reverse fork rod with
reverse gear assembly sleeve.
NOTE:
If installation is difficult, gently return shift lever of control shaft
assembly counterclockwise slightly.
31. Fit shaft with bearing by rotating input shaft. Then, tighten bolts
to the specified torque. Refer to TM-635, "
Exploded View".
32. Apply recommended sealant to threads of position switch and
check ball plug. Then install them to transaxle case and tighten
to the specified torque. Refer to TM-635, "
Exploded View".
33. Apply gear oil to spline of mainshaft and then press in 5th main
gear (1) to mainshaft using a suitable bolt (A) [M10 x 1.0] and
nut (B).
34. Install spread springs to 5th-reverse synchronizer hub.
PCIB1524E
PCIB1553E
PCIB1528E
PCIB1554E