2007 NISSAN LATIO keyless entry

BL-118
INTELLIGENT KEY SYSTEM
Revision: June 20062007 Versa
REMOTE KEYLESS ENTRY FUNCTION MALFUNCTION
NOTE:

Before performing the diagnosis in the following table, check “Trouble Diagnosis Procedure”. Refer to BL-
109, "Trouble Diagnosis Procedure" .

Make sure that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis,
and check each symptom.

If the following “symptoms” are detected, check systems shown in the “Diagnosis/service procedure” col-
umn in this order.
Conditions of Vehicle (Operating Conditions)

Ignition switch is not depressed.

All doors are closed.
Symptom Diagnosis/service procedureReference
page
All of the remote keyless entry functions
do not operate.1. Check Intelligent Key unit power supply and ground circuit.BL-123
2. Check key switch (BCM input).BL-126
3. Check Intelligent Key battery.BL-159
4. Remote Keyless Entry function inspection.BL-159
5. Replace Intelligent Key unit.BL-160
Auto lock function does not operate.1. Check “AUTO RELOCK TIMER” setting in “WORK SUPPORT”.BL-1132. Replace Intelligent Key unit.BL-160
Key reminder function does not operate.1. Check door switch.BL-129
2. Check inside key antenna.BL-143
3. Check unlock sensor.BL-136
4. Check Intelligent Key battery.BL-159
5. Replace Intelligent Key unit.BL-160
Panic alarm function does not operate.1. Check “PANIC ALARM DELAY” setting in “WORK SUPPORT”.BL-113
2. Check Intelligent Key battery inspection.BL-159
3. Check horn function.BL-157
4. Check headlamp function.BL-158
5. Check key switch.BL-124
6. Check ignition knob switch.BL-127
7. Replace Intelligent Key unit.BL-160

INTELLIGENT KEY SYSTEM
BL-159
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
Intelligent Key Battery ReplacementEIS0092W
DISASSEMBLY AND ASSEMBLY OF INTELLIGENT KEY
1. Release the lock knob at the back of the Intelligent Key and remove the mechanical key.
2. Insert a flat-blade screwdriver (A) wrapped with a cloth into the
slit of the corner and twist it to separate the upper part from the
lower part.
CAUTION:

Be careful not to touch the circuit board or battery termi-
nal.

The key fob is water-resistant. However, if it does get wet,
immediately wipe it dry.
3. Replace the battery with new one.
4. Align the tips of the upper and lower parts, and then push them
together until it is securely closed.
CAUTION:

When replacing battery, be sure to keep dirt, grease, and
other foreign materials off the electrode contact area.

After replacing the battery, check to make sure all Intelli-
gent Key functions work normally.
INTELLIGENT KEY BATTERY INSPECTION
Check by connecting a resistance (approximately 300Ω) so that the
current value becomes about 10 mA.
Remote Keyless Entry FunctionEIS0 09 DF
Check keyfob function using Remote Keyless Entry Tester J-43241.
PIIB6221E
PIIB6222E
Standard : Approx. 2.5 - 3.0V
OCC0607D
LEL946A

VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-195
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa

through 10A fuse (No. 28, located in the fuse and fusible link box)

to horn relay terminal 2

through 15A fuse (No. 52, located in the IPDM E/R)

to IPDM E/R internal CPU.

through 20A fuse (No. 53, located in the IPDM E/R)

to IPDM E/R internal CPU.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 20, located in the fuse block (J/B)]

to BCM terminal 11.
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to BCM terminal 38.
Ground is supplied

to BCM terminal 67

through body grounds M57 and M61.
INITIAL CONDITION TO ACTIVATE THE SYSTEM
The operation of the vehicle security system is controlled by the doors.
To activate the vehicle security system, BCM must receive signals indicating the ignition switch is OFF, doors
are closed and locked.
When a door is open, BCM terminal 12, 13, 43, 47 or 48 receives a ground signal from each door switch. In
addition to BCM, when back door is open, the Intelligent Key unit terminal 23 receives a ground signal from
back door through BCM terminal 30.
When front door LH is unlocked, BCM terminal 46 receives a signal from terminal 6 of main power window and
door lock/unlock switch.
When front door RH is unlocked, BCM terminal 46 receives a signal from terminal 2 of power window and door
lock/unlock switch RH.
VEHICLE SECURITY SYSTEM ALARM OPERATION
The vehicle security system is triggered by

opening a door

unlocking door without using the key, keyfob or Intelligent Key.
The vehicle security system will be triggered once the system is in armed phase,

when BCM receives a ground signal at terminals 12, 13, 47, 48 (front or rear door switch), or terminal 43
(back door switch).
When the vehicle security system is triggered, ground is supplied intermittently

from IPDM E/R terminal 45

to horn relay terminal 1.
The headlamps flash and the horn sounds intermittently.
The alarm automatically turns off after 50 seconds, but will reactivate if the vehicle is tampered with again.
VEHICLE SECURITY SYSTEM DEACTIVATION
To deactivate the vehicle security system, a door must be unlocked with the key, keyfob or Intelligent Key.
When the key is used to unlock the driver door, BCM terminal 7 receives signal

from terminal 3 of the front door key cylinder switch LH.
When the BCM receives this signal or unlock signal from keyfob or Intelligent Key or front door key cylinder
switch LH, the vehicle security system is deactivated. (Disarmed phase)
PANIC ALARM OPERATION
Intelligent Key and remote keyless entry system may or may not operate vehicle security system (horn and
headlamps) as required.
When the remote keyless entry system is triggered, ground is supplied intermittently

from IPDM E/R terminal 45

to horn relay terminal 1.
The headlamp flashes and the horn sounds intermittently.

BL-204
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: June 20062007 Versa
Trouble DiagnosisEIS009B3
WORK FLOW

For “POWER DOOR LOCK SYSTEM” diagnosis, refer to BL-23, "POWER DOOR LOCK SYSTEM" .

For "INTELLIGENT KEY SYSTEM” diagnosis, refer to BL-80, "INTELLIGENT KEY SYSTEM" .

For “REMOTE KEYLESS ENTRY SYSTEM” diagnosis, refer to BL-54, "REMOTE KEYLESS ENTRY
SYSTEM" .
LIIA2635E

BL-206
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Revision: June 20062007 Versa
Symptom ChartEIS009B5
*1 : Make sure the system is in the armed phase.SYMPTOM PROCEDURE Diagnostic procedure
1Vehicle security
system cannot be
set by ····AII itemsDiagnostic Procedure 1 (Door switch check)
Refer to BL-207, "
Diagnostic Procedure 1" .
If the above systems are “OK”, replace BCM. Refer to BCS-25, "
Removal
and Installation of BCM" .
Lock/unlock switchDiagnostic Procedure 6 (Door lock/unlock switch check)
Refer to BL-211, "
Diagnostic Procedure 6" .
If the above systems are “OK”, check main power window and door lock/
unlock switch. Refer to GW-17, "
POWER WINDOW SYSTEM" .
Door outside key (driver)Diagnostic Procedure 3 (Door key cylinder switch check)
Refer to BL-211, "
Diagnostic Procedure 3" .
If the above systems are “OK”, check main power window and door lock/
unlock switch. Refer to GW-17, "
POWER WINDOW SYSTEM" .
Intelligent keyCheck Intelligent Key entry function. Refer to BL-82, "
System Description"
If the above systems are “OK”, replace BCM. Refer to BCS-25, "Removal
and Installation of BCM" .
Keyfob (without Intelligent Key)Check remote keyless entry function. Refer to BL-61, "
Preliminary Check"
.
If the above systems are “OK”, replace BCM. Refer to BCS-25, "
Removal
and Installation of BCM" .
2Security indicator
does not turn
“ON”.Security indicator lampDiagnostic Procedure 2 (Security indicator lamp check)
Refer to BL-210, "
Diagnostic Procedure 2" .
If the above systems are “OK”, replace BCM. Refer to BCS-25, "
Removal
and Installation of BCM" .
3*1 Vehicle secu-
rity system does
not alarm when
····Any door is opened.Diagnostic Procedure 1 (Door switch check)
Refer to BL-207, "
Diagnostic Procedure 1" .
If the above systems are “OK”, replace BCM. Refer to BCS-25, "
Removal
and Installation of BCM" .
4Vehicle security
alarm does not
activate.Horn alarmDiagnostic Procedure 4 (Vehicle security horn alarm check).
Refer to BL-211, "
Diagnostic Procedure 4" .
If the above systems are “OK”, check horn system.
Refer to WW-46, "
HORN" .
Head lamp alarmDiagnostic Procedure 5 (Head lamp alarm check).
Refer to BL-211, "
Diagnostic Procedure 5" .
If the above systems are “OK”, replace BCM. Refer to BCS-25, "
Removal
and Installation of BCM" .
5Vehicle security
system cannot be
canceled by ····Door outside key (driver)Diagnostic Procedure 3 (Door key cylinder switch check).
Refer to BL-211, "
Diagnostic Procedure 3" .
If the above systems are “OK”, check main power window and door lock/
unlock switch. Refer to GW-17, "
POWER WINDOW SYSTEM" .
Intelligent keyCheck Intelligent Key entry function. Refer to BL-82, "
System Description"
If the above systems are “OK”, replace BCM. Refer to BCS-25, "Removal
and Installation of BCM" .
Keyfob (without Intelligent Key)Check remote keyless entry function. Refer to BL-61, "
Preliminary Check"
.
If the above systems are “OK”, replace BCM. Refer to BCS-25, "
Removal
and Installation of BCM" .

IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
K
KEYLES - Wiring diagram .................................. BL-57
Knock sensor (KS) .......................................... EC-315
KS - Wiring diagram ........................................ EC-316
L
L/USSV - Wiring diagram .............................. CVT-159
Line pressure and secondary pressure control CVT-26
Line pressure solenoid valve ......... CVT-113, CVT-118
Line pressure test (A/T) ...................................... AT-56
Liquid gasket application ................ EM-5, LU-2, CO-3
Location of electrical units ................................. PG-64
Lock-up and select control .............................. CVT-28
Lock-up select solenoid valve ....................... CVT-158
Low tire pressure warning system ....................... WT-7
Low tire pressure warning system - trouble diagnoses
WT-10
Low tire pressure warning system - Wiring diagram ....
WT-10
LPSV - Wiring diagram .................... AT-146, CVT-114
Lubricant (R134a) A/C ...................... MTC-5, MTC-18
Lubrication circuit (engine) ................................... LU-4
Lubrication oil A/C .......................................... MTC-96
M
M/T major overhaul ........................................... MT-17
M/T removal and installation ............................. MT-15
MAFS - Wiring diagram ..................... EC-181, EC-189
Magnet clutch ................................................. MTC-41
MAIN - Wiring diagram ...................... EC-144, AT-183
Mainshaft (M/T) ................................................. MT-18
Maintenance ........................................................ MA-5
Malfunction indicator lamp (MIL) ....................... EC-61
Manual air conditioner - Wiring diagram ........ MTC-29
Mass air flow sensor (MAFS) ............ EC-178, EC-187
Master cylinder (clutch) ........................................ CL-9
Meter ..................................................................... DI-5
METER - Wiring diagram ...................................... DI-9
MIL data link connectors circuit ....................... EC-592
MIRROR - Wiring diagram ............................... GW-64
Mirror, door ....................................................... GW-65
Mirror, out side ................................................. GW-65
Misfire .............................................................. EC-308
Mode door control linkage adjustment ........... MTC-71
Molding - See Exterior .............................. EI-23, EI-24
Mud guard - See Exterior .................................... EI-26
Multiport fuel injection (MFI) system ................. EC-23
Multiport fuel injection precautions ....................... GI-6
Multi-remote control system - See Remote keyless entry
system ................................................................ BL-54
N
NATS - Wiring diagram .................................... BL-215
NATS (Nissan anti-theft system) precautions ...... GI-3
NONDTC - Wiring diagram ............. AT-193, CVT-176
NVH troubleshooting (BR) ................................... BR-5
NVH troubleshooting (RSU) ............................. RSU-4
NVIS (Nissan vehicle immobilizer system) ....... BL-212
O
Oil change (capacity) ......................................... MA-11
Oil cooler (engine) ............................................. EM-24
Oil filter ................................................................ LU-8
Oil pan (engine) ................................................. EM-24
Oil pressure (engine) ........................................... LU-5
Oil seal replacement (engine) . EM-24, EM-37, EM-59,
EM-66
On board diagnostic system .............................. EC-47
ORVR (On-board Refueling Vapor Recovery) ... EC-38
Out side mirror .................................................. GW-65
Overdrive control switch ..................... AT-186, AT-191
Overheat .......................................................... EC-443
OVRCSV - Wiring diagram .............................. AT-162
P
P/SCKT - Wiring diagram ................................ WW-44
Park/Neutral position switch ............................ EC-436
Park/neutral position switch (A/T) ......... AT-97, AT-186
Park/neutral position switch (CVT) .................. CVT-78
Park/neutral position switch (M/T) ..................... MT-11
Parking brake control ........................................... PB-4
PCV (positive crankcase ventilation) ................. EC-44
Periodic maintenance .......................................... MA-7
PGC/V - Wiring diagram .................... EC-356, EC-364
PHASE - Wiring diagram ................................. EC-329
Pilot bushing replacement ................................. EM-77
Piston assembly ................................................ EM-99
Piston pin inspection .......................................... EM-95
Piston ring inspection ........................................ EM-96
Piston to bore clearance .................................... EM-99
PNP/SW - Wiring diagram ..... EC-438, AT-98, CVT-80
POS - Wiring diagram ...................................... EC-321
POWER - Wiring diagram ................... CVT-146, PG-6
Power door lock .................................................. BL-23
Power socket ................................................... WW-44
Power steering gear .......................................... PS-12
Power supply routing ........................................... PG-4
Power window .................................................. GW-17
PRE/SE - Wiring diagram .................. EC-387, EC-393
Precations for Leak detection dye .................. MTC-10
Precautions (General) .......................................... GI-4
Pressure control solenoid valve A CVT-113, CVT-118
Pressure control solenoid valve B CVT-121, CVT-124
Pressure plate - See Clutch cover ..................... CL-13
Pressure test (CVT) ......................................... CVT-45
Primary pressure sensor ............................... CVT-137
Primary Speed Sensor .................................... CVT-90
PRIPS - Wiring diagram ................................ CVT-138
PRSCVT - Wiring diagram ............................... CVT-91
PT/SEN - Wiring diagram ................................ AT-177

IDX-6
ALPHABETICAL INDEX
R
Radiator ............................................................ CO-11
Rear axle .......................................................... RAX-4
Rear combination lamp removal and installation LT-87
Rear door .......................................................... GW-47
Rear seat belt ...................................................... SB-6
Rear suspension ............................................... RSU-5
Rear washer .................................................... WW-30
Rear window defogger ...................................... GW-50
Rear wiper ....................................................... WW-30
Refrigerant connection precaution .................... MTC-5
Refrigerant discharging evacuating charging . MTC-80
Refrigerant general precaution ......................... MTC-5
Refrigerant lines .............................................. MTC-80
Refrigerant pressure sensor ............. EC-586, MTC-88
Refrigeration cycle .......................................... MTC-16
Remote keyless entry system ............................ BL-54
Removal and installation (A/T) ......................... AT-253
Reverse idler shaft (M/T) ................................... MT-18
Reverse lamp switch (M/T) - See Back-up lamp switch
(M/T) .................................................................. MT-11
Reverse main gear (M/T) ................................... MT-18
Road test ......... AT-58, AT-61, AT-64, AT-65, CVT-46
Room lamp - See Interior lamp ........................... LT-91
RP/SEN - Wiring diagram ................................ EC-587
S
SAE J1979 - Service $01 - 09 ........................... EC-47
Seat belt inspection ................................ SB-8, MA-27
Seat belt, front ..................................................... SB-3
Seat belt, rear ...................................................... SB-6
Secondary pressure sensor ........................... CVT-129
Secondary Speed Sensor ................................ CVT-95
SECPS - Wiring diagram ............................... CVT-130
SECPSV - Wiring diagram ............................. CVT-125
Self-diagnostic results .......................... EC-64, EC-116
SEN/PW - Wiring diagram ............................... EC-431
SESCVT - Wiring diagram ............................... CVT-96
SHIFT - Wiring diagram ................... AT-236, CVT-198
Shift control ...................................................... CVT-26
Shift control components (M/T) .......................... MT-21
Shift control system ....................................... CVT-191
Shift fork (M/T) ................................................... MT-21
Shift lever ........................................................... MT-12
Shift lock system .............................................. AT-235
Shift schedule ..................... AT-67, CVT-53, CVT-210
Shock absorber (rear) ....................................... RSU-9
Side air bag (satellite) sensor ......................... SRS-50
Side curtain air bag ......................................... SRS-47
Side trim .............................................................. EI-32
SMJ (super multiple junction) ............................ PG-75
Specification value ........................................... EC-133
Speedometer ........................................................ DI-5
Spiral cable ..................................................... SRS-44
Spot lamp .......................................................... LT-107
SPSW - Wiring diagram ................................. CVT-171
SROOF - Wiring diagram ................................... RF-13
SRS - See Supplemental Restraint System ...... SRS-4
SRS - Wiring diagram ..................................... SRS-13
SRS Trouble diagnoses .................................... SRS-9
SSV/A - Wiring diagram ................................... AT-152
SSV/B - Wiring diagram ................................... AT-157
Stall Test ......................................................... CVT-43
Stall test (A/T) .................................................... AT-53
START - Wiring diagram ................................... SC-12
Starting system ................................................. SC-10
Steering linkage ................................................. PS-12
Steering wheel and column ........................ PS-6, PS-9
Steering wheel turning force ................................ PS-6
Step motor .................................... CVT-164, CVT-168
STM - Wiring diagram ................................... CVT-165
Stop lamp ................................................ LT-71, LT-87
Stop lamp switch ............................................. EC-488
STOP/L - Wiring diagram ................................... LT-71
STSIG - Wiring diagram .................................. CVT-73
Sun roof, electric ................................................ RF-10
Sunroof .................................................. RF-10, RF-22
Supplemental Restraint System ........................ SRS-4
Suspension ....................................................... MA-26
Swirl control valve ........................................... EC-592
Symbols and abbreviations ...................... GI-10, GI-23
Symptom matrix chart ....................................... EC-92
Synchronizer (M/T) ........................................... MT-18
System readiness test (SRT) code ................... EC-52
T
Tachometer ........................................................... DI-5
Tail lamp ............................................................ LT-87
TAIL/L - Wiring diagram ..................................... LT-78
TCM circuit diagram ........................................ CVT-42
TCM function ................................................... CVT-24
TCM inspection table ........................... AT-78, CVT-54
TCV - Wiring diagram ...................... AT-135, CVT-106
Telephone .......................................................... AV-49
Theft warning system - See Vehicle security (Theft warn-
ing) system ....................................................... BL-193
Thermo control amp ........................................ MTC-63
Thermostat ........................................................ CO-18
Three way catalyst function ............................ EC-334
Three way catalyst precautions ............................ GI-5
Throttle control motor relay ............................. EC-493
Throttle position sensor (TPS) .. EC-206, EC-302, EC-
460, EC-462, EC-526
Throttle valve closed position learning .............. EC-78
Tie-rod ................................................................ PS-12
Timing chain ...................................................... EM-37
TLID - Wiring diagram ...................................... BL-177
Torque converter installation .... AT-254, AT-369, CVT-
208
Torque convertor clutch solenoid valve CVT-105, CVT-
110
TPS1 - Wiring diagram .................................... EC-304
TPS2 - Wiring diagram .................................... EC-208
TPS3 - Wiring diagram .................................... EC-528
Transmission case (M/T) .................................. MT-17

LT-2Revision: June 20062007 Versa Daytime Light Control Does Not Operate Properly
(High Beam Headlamps Operate Properly) ............ 35
Aiming Adjustment .................................................. 37
PREPARATION BEFORE ADJUSTING .............. 37
LOW BEAM AND HIGH BEAM ........................... 37
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 38
Bulb Replacement .................................................. 39
HEADLAMP (HIGH/LOW) ................................... 39
PARKING (CLEARANCE) LAMP ......................... 39
FRONT TURN SIGNAL LAMP ............................ 39
Removal and Installation ........................................ 39
REMOVAL ........................................................... 39
INSTALLATION .................................................... 39
Disassembly and Assembly .................................... 40
DISASSEMBLY ................................................... 40
ASSEMBLY ......................................................... 40
FRONT FOG LAMP .................................................. 41
Component Parts and Harness Connector Location ... 41
System Description ................................................. 41
OUTLINE ............................................................. 41
FOG LAMP OPERATION .................................... 42
COMBINATION SWITCH READING FUNCTION ... 42
EXTERIOR LAMP BATTERY SAVER CONTROL ... 42
CAN Communication System Description .............. 42
Wiring Diagram — F/FOG — .................................. 43
Terminals and Reference Values for BCM .............. 45
Terminals and Reference Values for IPDM E/R ...... 45
How to Proceed With Trouble Diagnosis ................ 45
Preliminary Check .................................................. 45
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM ................................................... 45
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR IPDM E/R ........................................... 45
CONSULT-II Function (BCM) .................................. 45
CONSULT-II Function (IPDM E/R) .......................... 45
Front Fog lamps Do Not Illuminate (Both Sides) .... 45
Front Fog Lamp Does Not Illuminate (One Side) ... 48
Aiming Adjustment .................................................. 49
Bulb Replacement .................................................. 49
Removal and Installation ........................................ 50
REMOVAL ........................................................... 50
INSTALLATION .................................................... 50
TURN SIGNAL AND HAZARD WARNING LAMPS ... 51
Component Parts and Harness Connector Location ... 51
System Description ................................................. 51
TURN SIGNAL OPERATION ............................... 51
HAZARD LAMP OPERATION ............................. 52
REMOTE KEYLESS ENTRY SYSTEM OPERA-
TION .................................................................... 53
COMBINATION SWITCH READING FUNCTION ... 53
CAN Communication System Description .............. 53
Schematic ............................................................... 54
Wiring Diagram — TURN — ................................... 55
Terminals and Reference Values for BCM .............. 59
How to Proceed With Trouble Diagnosis ................ 59
Preliminary Check .................................................. 59
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM ................................................... 59CONSULT-II Function (BCM) ..................................59
Turn Signals Do Not Operate ..................................59
Front Turn Signal Lamp Does Not Operate ............59
Rear Turn Signal Lamp Does Not Operate .............60
Hazard Warning Lamp Does Not Operate But Turn
Signal Lamp Operates ............................................62
Turn Signal Indicator Lamp Does Not Operate .......63
Bulb Replacement of Front Turn Signal Lamp ........64
Bulb Replacement of Rear Turn Signal Lamp .........64
Removal and Installation of Front Turn Signal Lamp ...64
Removal and Installation of Rear Turn Signal Lamp ...64
LIGHTING AND TURN SIGNAL SWITCH ................65
Removal and Installation .........................................65
REMOVAL ............................................................65
INSTALLATION ....................................................65
HAZARD SWITCH .....................................................66
Removal and Installation .........................................66
REMOVAL ............................................................66
INSTALLATION ....................................................66
COMBINATION SWITCH ..........................................67
Wiring Diagram — COMBSW — ............................67
Combination Switch Reading Function ...................68
Terminals and Reference Values for BCM ..............68
CONSULT-II Function (BCM) ..................................68
Combination Switch Inspection ...............................68
Removal and Installation .........................................70
STOP LAMP ..............................................................71
Wiring Diagram — STOP/L — ................................71
Bulb Replacement of High-Mounted Stop Lamp .....72
Bulb Replacement of Rear Combination Lamp for
Stop Lamp ...............................................................72
Removal and Installation of High-Mounted Stop
Lamp .......................................................................72
REMOVAL ............................................................72
INSTALLATION ....................................................72
Removal and Installation of Rear Combination
Lamp for Stop Lamp ................................................72
BACK-UP LAMP .......................................................73
Wiring Diagram — BACK/L — ................................73
Bulb Replacement ...................................................74
Removal and Installation .........................................74
PARKING, LICENSE PLATE AND TAIL LAMPS ......75
Component Parts and Harness Connector Location ...75
System Description .................................................75
OPERATION BY LIGHTING SWITCH .................75
COMBINATION SWITCH READING FUNCTION ...76
EXTERIOR LAMP BATTERY SAVER CONTROL ...76
CAN Communication System Description ..............76
Schematic ...............................................................77
Wiring Diagram — TAIL/L — ...................................78
Terminals and Reference Values for BCM ..............81
Terminals and Reference Values for IPDM E/R ......81
How to Proceed With Trouble Diagnosis ................81
Preliminary Check ...................................................81
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM ...................................................81
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR IPDM E/R ...........................................81
CONSULT-II Function (BCM) ..................................81