WW-30
FRONT WIPER AND WASHER SYSTEM
Revision: 2006 November2007 350Z
Removal and Installation of Front Wiper Arms, Adjustment of Wiper Arms Stop
Location
NKS0052L
REMOVAL
1. Turn front wiper switch ON to operate wiper motor, and then turn front wiper switch OFF (auto stop).
2. Remove washer tube from washer tube joint.
3. Open hood, remove front wiper arm caps, and remove front wiper arm nuts.
4. Raise front wiper arms, and remove front wiper arms from vehicle.
INSTALLATION
1. Clean up the pivot area as shown in the figure. This will reduce
possibility of front wiper arm looseness.
2. Prior to front wiper arms installation, turn front wiper switch ON
to operate wiper motor, and then turn front wiper switch OFF
(auto stop).
3. Lift the blade up and then set it down onto windshield glass sur-
face to set the blade center to clearance “L1” & “L2” immedi-
ately.
4. Tighten front wiper arm nuts to specified torque.
5. Install washer tube from washer tube joint.
6. Spray washer fluid. Turn front wiper switch ON to operate wiper
motor, and then turn front wiper switch OFF (auto stop).
7. Make sure that wiper blades stop within clearance “L1” & “L2”.
8. Install front wiper arm caps.
Removal and Installation of Front Wiper Drive AssemblyNKS0052M
REMOVAL
1. Remove front wiper arms. Refer to WW-30, "REMOVAL" .
2. Remove cowl top cover. Refer to EI-20, "
COWL TOP" .
3. Disconnect wiper motor connector (1) and remove connector
clip (A).
4. Remove front wiper drive assembly mounting bolts (B), and
remove front wiper drive assembly (2) from the vehicle.
INSTALLATION
1. Install front wiper drive assembly to the vehicle.
2. Connect wiper motor connector. Turn front wiper switch ON to operate wiper motor, and then turn front
wiper switch OFF (auto stop).
3. Install connector clips to the wiper frame, and install cowl top cover. Refer to EI-20, "
COWL TOP" .
SEL024J
Front wiper arm nuts : 23.6 N·m (2.4 kg-m, 18 ft-lb)
Clearance “L1” : 63.9 ± 7.5 mm (2.516 ± 0.295 in)
Clearance “L2” : 32.0 ± 6.5 mm (1.260 ± 0.256 in)
PKIA9951E
SKIB7455E
Front wiper drive assembly mounting bolts : 4.5 N·m (0.46 kg-m, 40 in-lb)
REAR WIPER AND WASHER SYSTEM
WW-47
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: 2006 November2007 350Z
INSTALLATION
1. Clean up the pivot area as shown in the figure. This will reduce
possibility of rear wiper arm nut looseness.
2. Prior to rear wiper arm installation, turn rear wiper switch ON to
operate wiper motor, and then turn rear wiper switch OFF (auto
stop).
3. Lift the blade up and then set it down onto windshield glass sur-
face to set the blade center to clearance “L” immediately.
4. Tighten wiper arm nuts to specified torque.
5. Spray washer fluid. Turn rear wiper switch ON to operate wiper
motor, and then turn rear wiper switch OFF (auto stop).
6. Make sure that wiper blade stop within clearance “L”.
7. Install rear wiper arm caps.
Removal and Installation of Rear Wiper Motor NKS0053B
SKIA0082J
Rear wiper arm nut : 15.2 N·m (1.6 kg-m, 11 ft-lb)
Clearance “L” : 30 ± 7.5 mm (1.181 ± 0.295 in)
PKIA1914E
PKIB5009E
WW-54
HORN
Revision: 2006 November2007 350Z
Removal and InstallationNKS0053O
REMOVAL
1. Disconnect all horn connectors.
2. Remove horn mounting bolt and remove horn from vehicle.
INSTALLATION
Tighten horn bolt to specified torque.
PKIA1917E
Horn mounting bolt : 5.7 N·m (0.58 kg-m, 50 in-lb)
