2007 NISSAN 350Z center console

SE-1
SEAT
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION SE
A
B
SE
Revision: 2006 November2007 350Z
SEAT
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Service Notice .......................................................... 3
Precautions for Battery Service ................................ 3
Precautions for Work ................................................ 3
PREPARATION ........................................................... 5
Special Service Tools ............................................... 5
Commercial Service Tools ........................................ 5
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 6
Work Flow ................................................................ 6
CUSTOMER INTERVIEW ..................................... 6
DUPLICATE THE NOISE AND TEST DRIVE ....... 7
CHECK RELATED SERVICE BULLETINS ........... 7
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 7
REPAIR THE CAUSE ........................................... 7
CONFIRM THE REPAIR ....................................... 8
Generic Squeak and Rattle Troubleshooting ........... 8
INSTRUMENT PANEL .......................................... 8
CENTER CONSOLE ............................................. 8
DOORS ................................................................. 8
TRUNK .................................................................. 9
SUNROOF/HEADLINING ..................................... 9
SEATS ................................................................... 9
UNDERHOOD ....................................................... 9
Diagnostic Worksheet ............................................ 10
POWER SEAT/FOR COUPE .................................... 12
Wiring Diagram–SEAT– /For Driver Seat ............... 12
Wiring Diagram–SEAT– /For Passenger Seat ....... 14
POWER SEAT/FOR ROADSTER ............................. 15
Component Parts and Harness Connector Location ... 15
System Description ................................................ 16
DRIVER SIDE SEAT OPERATION ..................... 16
PASSENGER SIDE SEAT MANUAL OPERA-
TION .................................................................... 17
PASSENGER SEATBACK TILT FORWARD/
BACKWARD OPERATION .................................. 18
INTERLOCKING OPERATION OF THE PAS-SENGER SEAT WITH THE SOFT TOP .............. 19
PASSENGER SIDE RECLINING MOTOR
OPERATION ........................................................ 20
SEATBACK TILT CANCEL SWITCH OPERA-
TION .................................................................... 20
MANUAL OPERATION ........................................ 21
AUTOMATIC OPERATION .................................. 21
CANCEL FUNCTION .......................................... 25
FAIL-SAFE MODE ............................................... 25
Wiring Diagram–SEAT– / For Driver Seat .............. 26
Schematic / For Passenger Seat ............................ 28
Wiring Diagram–SEAT– / For Passenger Seat ....... 29
Terminals and Reference Values of Passenger Seat
Control Unit ............................................................. 34
Terminals and Reference Values of BCM ............... 35
Terminals and Reference Values of Soft Top Control
Unit ......................................................................... 37
Terminals and Reference Values of Unified Meter
and A/C Amp. ......................................................... 37
Work Flow ............................................................... 37
Trouble Diagnosis Symptom Chart ......................... 37
Check BCM Power Supply and Ground ................. 38
Check Driver Side Seat Power Supply and Ground ... 40
Check Driver Side Seat Sliding Motor Circuit ......... 41
Check Driver Side Seat Reclining Motor Circuit ..... 42
Check Passenger Seat Control Unit Power Supply
and Ground ............................................................. 44
Check Passenger Seat Control Unit Ignition Signal
Circuit ..................................................................... 44
Check Passenger Side Seat Sliding Motor Circuit ... 45
Check Passenger Side Seat Reclining Motor Circuit ... 46
Check Passenger Side Seat Reclining Sensor Cir-
cuit .......................................................................... 47
Check Passenger Side Seat Sliding Switch Circuit ... 48
Check Passenger Side Seat Reclining Switch Cir-
cuit .......................................................................... 49
Check Passenger Side Power Seat Switch Ground
Circuit ..................................................................... 50
Check Seatback Tilt Switch Circuit ......................... 51
Check Seatback Tilt Cancel Switch Circuit ............. 52

SE-8
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Revision: 2006 November2007 350Z
INSULATOR (Light foam block)
80845-71L00: 30 mm (1.18 in) thick, 30×50 mm (1.18×1.97 in)
FELT CLOTHTAPE
Used to insulate where movement does not occur. Ideal for instrument panel applications.
68370-4B000: 15×25 mm (0.59×0.98 in) pad/68239-13E00: 5 mm (0.20 in) wide tape roll
The following materials, not found in the kit, can also be used to repair squeaks and rattles.
UHMW (TEFLON) TAPE
Insulates where slight movement is present. Ideal for instrument panel applications.
SILICONE GREASE
Used in place of UHMW tape that will be visible or not fit. Will only last a few months.
SILICONE SPRAY
Use when grease cannot be applied.
DUCT TAPE
Use to eliminate movement.
CONFIRM THE REPAIR
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Generic Squeak and Rattle TroubleshootingNIS0029C
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1. The cluster lid A and instrument panel
2. Acrylic lens and combination meter housing
3. Instrument panel to front pillar garnish
4. Instrument panel to windshield
5. Instrument panel mounting pins
6. Wiring harnesses behind the combination meter
7. A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by
applying felt cloth tape or silicon spray (in hard to reach areas). Urethane pads can be used to insulate
wiring harness.
CAUTION:
Do not use silicone spray to isolate a squeak or rattle. If you saturate the area with silicone, you
will not be able to recheck the repair.
CENTER CONSOLE
Components to pay attention to include:
1. Shifter assembly cover to finisher
2. A/C control unit and cluster lid C
3. Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to the center console.
DOORS
Pay attention to the:
1. Finisher and inner panel making a slapping noise
2. Inside handle escutcheon to door finisher
3. Wiring harnesses tapping
4. Door striker out of alignment causing a popping noise on starts and stops
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. You can usually insulate the areas with felt cloth tape or insulator foam blocks from
the Nissan Squeak and Rattle Kit (J-43980) to repair the noise.