2007 NISSAN 350Z check engine

RF-74
SOFT TOP
Revision: 2006 November2007 350Z
2. CHECK 5TH BOW FULL-LATCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and soft top lock switch (at 5th bow lock assembly in storage lid) connec-
tor.
3. Check continuity between soft top control unit connector B67
terminal 30 and soft top lock switch connector T205 terminal 3.
4. Check continuity between soft top control unit connector B67
terminal 30 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK 5TH BOW HALF-LATCH SWITCH GROUND CIRCUIT
Check continuity between soft top lock switch connector T205 terminal 4 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK SOFT TOP CONTROL UNIT OUTPUT SIGNAL
1. Connect soft top control unit connector.
2. Start engine.
3. Check voltage between soft top control unit connector B67 ter-
minal 30 and ground.
OK or NG
OK >> Replace 5th bow assembly in storage lid.
NG >> Replace soft top control unit.30 (Y/R) - 3 (Y) : Continuity should exist.
30 (Y/R) - Ground : Continuity should not exist.
PIIA7934E
4 (B) - Ground : Continuity should exist.
PIIA7935E
30 (Y/R) - Ground : Approx. 5V
PIIA7933E

SOFT TOP
RF-75
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
Check 5th Bow Ending SwitchNIS0007C
1. CHECK 5TH BOW ENDING SWITCH SIGNAL
1. Start engine.
2. Operate soft top switch CLOSE, check voltage between soft top control unit connector and ground.
OK or NG
OK >> Soft top lock switch (5th bow ending switch) is OK.
NG >> GO TO 2.
2. CHECK 5TH BOW ENDING CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and soft top lock switch (at 5th bow lock assembly in storage lid) connec-
tor.
3. Check continuity between soft top control unit connector B67
terminal 29 and soft top lock switch connector T205 terminal 1.
4. Check continuity between soft top control unit connector B67
terminal 29 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK 5TH BOW ENDING SWITCH GROUND CIRCUIT
Check continuity between soft top lock switch connector T205 terminal 2 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
ConnectorTerminal (Wire color)
Roof conditionVoltage (V)
(Approx.)
(+) (-)
B67 29 (R/Y) Ground CL10 0 → 5
PIIA7936E
29 (R/Y) - 1 (R) : Continuity should exist.
29 (R/Y) - Ground : Continuity should not exist.
PIIA7937E
2 (B) - Ground : Continuity should exist.
PIIA7938E

RF-76
SOFT TOP
Revision: 2006 November2007 350Z
4. CHECK SOFT TOP CONTROL UNIT OUTPUT SIGNAL
1. Connect soft top control unit connector.
2. Start engine.
3. Check voltage between soft top control unit connector B67 ter-
minal 29 and ground.
OK or NG
OK >> Replace soft top lock switch (5th bow lock assembly in
storage lid).
NG >> Replace soft top control unit.
Check 5th Bow Closure MotorNIS0007D
1. 5TH BOW CLOSURE MOTOR INPUT SIGNAL
1. Start engine.
2. Operate soft top switch CLOSE, check voltage between 5th bow closure motor connector and ground.
OK or NG
OK >> Replace 5th bow closure motor.
NG >> GO TO 2.
2. CHECK 5TH BOW CLOSURE MOTOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and 5th bow closure motor connector.
3. Check continuity between soft top control unit connector B66
terminal 4, 12 and 5th bow closure motor connector T204 termi-
nal 1, 2.
4. Check continuity between soft top control unit connector B66
terminal 4, 12 and ground.
OK or NG
OK >> Replace soft top control unit.
NG >> Repair or replace harness.29 (R/Y) - Ground : Approx. 5V
PIIA7936E
ConnectorTerminal (Wire color)
Roof conditionVoltage (V)
(Approx.)
(+) (-)
T204 1 (W) Ground CL9 → CL10 0 → Battery voltage → 0
PIIA7939E
4 (G/R) - 1 (W) : Continuity should exist.
12 (G/Y) - 2 (G) : Continuity should exist.
4 (G/R) - Ground : Continuity should not exist.
12 (G/Y) - Ground : Continuity should not exist.
PIIA7940E

SOFT TOP
RF-77
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
Check Soft Top Front Lock SwitchNIS001L7
1. SOFT TOP FRONT LOCK SWITCH SIGNAL
1. Start engine.
2. Check voltage between soft top control unit connector and ground.
OK or NG
OK >> Soft top front lock switch is OK.
NG >> GO TO 2.
2. CHECK 5TH BOW ENDING CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and soft top front lock switch connector.
3. Check continuity between soft top control unit connector B67
terminal 28 and soft top front lock switch connector R8 terminal
4.
4. Check continuity between soft top control unit connector B67
terminal 28 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK SOFT TOP FRONT LOCK SWITCH GROUND CIRCUIT
Check continuity between soft top front lock switch connector R8 terminal 3 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
ConnectorTerminal (Wire color)
ConditionVoltage (V)
(Approx.)
(+) (-)
B67 28 (LG/B) GroundFront
lockLock 5
Unlock 0
PIIB7354E
28 (LG/B) - 4 (LG/B) : Continuity should exist.
28 (LG/B) - Ground : Continuity should not exist.
PIIB7355E
3 (B/W) - Ground : Continuity should exist.
PIIB7356E

RF-78
SOFT TOP
Revision: 2006 November2007 350Z
4. CHECK SOFT TOP CONTROL UNIT OUTPUT SIGNAL
1. Connect soft top control unit connector.
2. Start engine.
3. Check voltage between soft top control unit connector B67 ter-
minal 28 and ground.
OK or NG
OK >> Replace soft top front lock switch (front lock striker RH).
NG >> Replace soft top control unit.
Check Operation Permission ConditionNIS0007E
First perform the “SELF-DIAG RESULT” in “BCM” with CONSULT-II, then perform the each trouble diagnosis
of malfunction system indicated “SELF-DIAG RESULT” of “BCM”. Refer to BCS-15, "
CONSULT-III Function
(BCM)" .
1. CHECK VEHICLE SPEED SIGNAL
1. Start engine.
2. Check the signal between soft top control unit connector and ground with oscilloscope.
OK or NG
OK >> GO TO 3.
NG >> GO TO 2.28 (LG/B) - Ground : Approx. 5V
PIIB7354E
ConnectorTerminal (Wire
color)
ConditionSignal
(Reference value.)
(+) (-)
B66 14 (W)
GroundSpeedome-
ter
operated
[When
vehicle
speed is
Approx.
40km/h
(25MPH)]
B67 23 (W/G)
PIIA7941EPKIA1935E
PIIB0078J

RF-80
SOFT TOP
Revision: 2006 November2007 350Z
5. CHECK BRAKE PEDAL SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit and stop lamp switch connector.
3. Continuity between soft top control unit connector B68 terminal
38 and stop lamp switch connector E111 terminal 4.
4. Continuity between soft top control unit connector B68 terminal
38 and ground.
OK or NG
OK >> GO TO 6.
NG >> Repair or replace harness.
6. CHECK STOP LAMP SWITCH
Continuity between stop lamp switch connector E111 terminal 3 and 4.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace stop lamp switch.
Check Each Switch Condition (Open Operate)NIS0007F
1. CHECK EACH SWITCH SIGNAL
1. Start engine.
2. Check voltage between soft top control unit connector and ground.
OK or NG
OK >> Each switch condition is OK.
NG >> Check malfunction switch.38 (W) - 4 (P/L) : Continuity should exist.
38 (W) - Ground : Continuity should not exist.
PIIB7357E
Connector Terminal Brake pedal condition Continuity
E 111 3 4Depressed Yes
Released No
PIIB7358E
ConnectorTerminal (Wire color)
Roof conditionVoltage (V)
(Approx.)
(+) (-)
B6720 (W/B)
Ground Full closed 5 21 (W/L)
22 (W/R)
24 (G)
25 (L/Y)
26 (LG)
27 (GY)
32 (W)
33 (BR)
PIIA7949E

SOFT TOP
RF-81
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
Check Each Switch Condition (Close Operate)NIS0007G
1. CHECK EACH SWITCH SIGNAL
1. Start engine.
2. Check voltage between soft top control unit connector and ground.
OK or NG
OK >> Each switch condition is OK.
NG >> Check malfunction switch.
Check Power Window Down Request SignalNIS0007H
1. CHECK POWER WINDOW REQUEST SIGNAL
1. Start engine.
2. Soft top switch operate, check voltage between soft top control unit connector and ground.
OK or NG
OK >> Check the condition of harness and connector.
NG >> Replace soft top control unit.
ConnectorTerminal (Wire color)
Roof conditionVoltage (V)
(Approx.)
(+) (-)
B6720 (W/B)
Ground Full opened0 21 (W/L)
22 (W/R)
24 (G)
5
25 (L/Y)
26 (LG)
0 27 (GY)
31 (L)
32 (W)
33 (P) 5
PIIA7950E
Con-
nectorTerminal (Wire color)
Roof conditionVoltage (V)
(Approx.)
(+) (-)
B67 36 (PU) GroundOP1 → OP11 (open operation)
5 → 0 → 5
CL1 → CL10 (close operation)
PIIA7955E

SOFT TOP
RF-83
C
D
E
F
G
H
J
K
L
MA
B
RF
Revision: 2006 November2007 350Z
Check Passenger Side Seat Operate Signal 2NIS0007K
1. CHECK PASSENGER SIDE SEAT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit, storage lid actuator RH and passenger seat control unit connector.
3. Check continuity between soft top control unit connector B66
terminal 13 and passenger seat control unit connector B354 ter-
minal 33.
4. Check continuity between soft top control unit connector B66
terminal 13 and ground.
OK or NG
OK >> Replace passenger seat control unit.
NG >> Repair or replace harness.
Check Passenger Side Seat Operate Signal 3NIS0007L
1. CHECK PASSENGER SIDE SEAT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect soft top control unit, passenger seat control unit and soft top lock switch connector.
3. Check continuity between passenger seat control unit connector
B353 terminal 11 and soft top control unit connector B67 termi-
nal 30.
4. Check continuity between soft top control unit connector B67
terminal 30 and ground.
OK or NG
OK >> Replace passenger seat control unit.
NG >> Repair or replace harness.
Check Seat Back Position SignalNIS0007M
1. CHECK SEAT BACK POSITION SIGNAL
1. Start engine.
2. The thing whose seat cancel switch is OFF is confirmed.
3. Soft top switch operate, check voltage between soft top control unit connector and ground.
OK or NG
OK >> Replace soft top control unit.
NG >> GO TO 2.13 (L/R) - 33 (G/B) : Continuity should exist.
13 (L/R) - Ground : Continuity should not exist.
PIIA7959E
11 (L/W) - 30 (Y/R) : Continuity should exist.
11 (L/W) - Ground : Continuity should not exist.
PIIB9257E
ConnectorTerminal (Wire color)
Seat conditionVoltage (V)
(Approx.)
(+) (-)
B67 34 (L/W) GroundWhen passenger seat
inclines forward5
Other than above 0
PIIA7961E