2007 NISSAN 350Z ignition

LT-114
PARKING, LICENSE PLATE AND TAIL LAMPS
Revision: 2006 November2007 350Z
Terminals and Reference Values for IPDM E/RNKS004Z6
How to Proceed With Trouble DiagnosisNKS004Z7
1. Confirm the symptom or customer complaint.
2. Understand operation description and function description. Refer to LT- 1 0 3 , "
System Description" .
3. Carry out preliminary check. Refer to LT- 11 4 , "
Preliminary Check" .
4. Check symptom and repair or replace the cause of malfunction.
5. Do parking, license plate, side marker and tail lamps operate normally? If YES, GO TO 6. If NO, GO TO 4.
6. INSPECTION END
Preliminary CheckNKS004Z8
CHECK POWER SUPPLY AND GROUND CIRCUIT
1. CHECK FUSES AND FUSIBLE LINK
Check for blown fuses and fusible link.
Refer to LT- 1 0 7 , "
Wiring Diagram — TAIL/L —" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
4, "POWER SUPPLY ROUTING CIRCUIT" .
39 L CAN − H— — —
40 P CAN − L— — —
42 GYBattery power
supplyOFF — Battery voltage
52 B Ground ON — Approx. 0 V
55 RBattery power
supplyOFF — Battery voltage Te r -
minal
No.Wire
colorSignal nameMeasuring condition
Reference value
Ignition
switchOperation or condition
Terminal
No.Wire color Signal nameMeasuring condition
Reference value
Ignition switch Operation or condition
22 RParking, license plate,
side marker and tail lampON Lighting switch 1ST positionOFF Approx. 0 V
ON Battery voltage
38 B Ground ON — Approx. 0 V
48 L CAN − H— — —
49 P CAN − L—— —
60 B Ground ON — Approx. 0 V
Unit Power source Fuse and fusible link No.
BCMBatteryF
18
Ignition switch ON or START position 1
Ignition switch ACC or ON position 6
IPDM E/R Battery 71

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-115
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check voltage between BCM harness connector terminals and
ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK GROUND CIRCUIT
Check continuity between BCM harness connector terminal and
ground.
OK or NG
OK >> INSPECTION END
NG >> Repair harness or connector.
CONSULT-III Function (BCM)NKS004Z9
Refer to LT- 1 7 , "CONSULT-III Function (BCM)" in HEADLAMP (FOR USA).
Refer to LT- 4 9 , "
CONSULT-III Function (BCM)" in HEADLAMP (FOR CANADA).
CONSULT-III Function (IPDM E/R)NKS004ZA
Refer to LT- 1 8 , "CONSULT-III Function (IPDM E/R)" in HEADLAMP (FOR USA).
Refer to LT- 5 0 , "
CONSULT-III Function (IPDM E/R)" in HEADLAMP (FOR CANADA).
Terminals Ignition switch position
(+)
(−)OFF ACC ON
BCM
connectorTerminal
M9011
GroundApprox. 0 VBattery
voltageBattery
voltage
38 Approx. 0 V Approx. 0 VBattery
voltage
M9142Battery
voltageBattery
voltageBattery
voltage
55Battery
voltageBattery
voltageBattery
voltage
PKIB5197E
BCM connector Terminal
GroundContinuity
M91 52 Yes
PKIB5198E

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-117
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
4. CHECK IPDM E/R
CONSULT-III ACTIVE TEST
1. Turn ignition switch OFF.
2. Disconnect front combination lamp, rear combination lamp and license plate lamp connectors.
3. Select "TAIL LAMP" of IPDM E/R active test item.
4. With operating the test item, check voltage between front combination lamp, rear combination lamp and
license plate lamp harness connector and ground.
IPDM E/R AUTO ACTIVE TEST
1. Turn ignition switch OFF.
2. Disconnect front combination lamp, rear combination lamp and license plate lamp connector.
3. Start auto active test. Refer to PG-20, "
Auto Active Test" .
4. With operating the test item, check voltage between front combination lamp, rear combination lamp and
license plate lamp harness connector and ground.
OK or NG
OK >> GO TO 6.
NG >> GO TO 5.
Terminals
Vo l ta g e
(Approx.) (+)
(-)
Front combination lamp
connectorTe r m i n a l
RH E24
6 Ground Battery voltage
LH E40
PKIA4606E
Terminals
Vo l ta g e
(Approx.) (+)
(-)
Rear combination lamp
connectorTe r m i n a l
RH T17
2 Ground Battery voltage
LH T9
PKIA4607E
Terminals
Vo l ta g e
(Approx.) (+)
(-)
License plate lamp
connectorTe r m i n a l
RH T104
2 Ground Battery voltage
LH T102
PKIA4608E

LT-118
PARKING, LICENSE PLATE AND TAIL LAMPS
Revision: 2006 November2007 350Z
5. CHECK CIRCUIT BETWEEN IPDM E/R AND PARKING, LICENSE PLATE, SIDE MARKER AND TAIL
LAMPS
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front combination lamp, rear combination
lamp and license plate lamp harness connector.
OK or NG
OK >> Replace IPDM E/R. Refer to PG-26, "Removal and
Installation of IPDM E/R" .
NG >> Repair harness or connector.
Terminals
Continuity IPDM E/R Front combination lamp
Connector Terminal Connector Terminal
E7 22RH E24 6
Ye s
LH E40 6
PKIA4603E
Terminals
Continuity IPDM E/R Rear combination lamp
Connector Terminal Connector Terminal
E7 22RH T17 2
Ye s
LH T9 2
PKIA4604E
Terminals
Continuity IPDM E/R Licence plat lamp
Connector Terminal Connector Terminal
E7 22RH T104 2
Ye s
LH T102 2
PKIA4605E

LT-120
PARKING, LICENSE PLATE AND TAIL LAMPS
Revision: 2006 November2007 350Z
2. ACTIVE TEST
CONSULT-III ACTIVE TEST
1. Select "TAIL LAMP" of IPDM E/R active test item.
2. With operating the test item, check the parking, license plate, side marker and tail lamps operation.
IPDM E/R AUTO ACTIVE TEST
1. Start auto active test. Refer to PG-20, "
Auto Active Test" .
2. With operating the test item, check the parking, license plate, side marker and tail lamps operation.
OK or NG
OK >> GO TO 3.
NG >> GO TO 4.
3. CHECK IPDM E/R
1. Select "TAIL&CLR REQ" of IPDM E/R data monitor item.
2. With operating the lighting switch, check the monitor status.
OK or NG
OK >> Replace IPDM E/R. Refer to PG-26, "Removal and Installation of IPDM E/R" .
NG >> Replace BCM. Refer to BCS-17, "
Removal and Installation of BCM" .
4. CHECK POWER SUPPLY CIRCUIT TO DAYTIME LIGHT RELAY
1. Turn ignition OFF.
2. Disconnect daytime light relay.
3. Check voltage between daytime light relay harness connector
and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.Parking, license plate, side marker and tail lamps
should operate.
Parking, license plate, side marker and tail lamps
should operate.
When lighting switch is 1ST
position: TAIL&CLR REQ ON
Te r m i n a l
voltage
(Approx.) (+)
(−)
Daytime light relay
connectorTe r m i n a l
E201
Ground Battery voltage
3
PKIA5152E

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-123
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
8. CHECK CIRCUIT BETWEEN IPDM E/R AND PARKING, LICENSE PLATE, SIDE MARKER AND TAIL
LAMPS
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front combination lamp, rear combination
lamp and license plate lamp harness connector.
OK or NG
OK >> Replace IPDM E/R. Refer to PG-26, "Removal and
Installation of IPDM E/R" .
NG >> Repair harness or connector.
Te r m i n a l s
Continuity IPDM E/R Front combination lamp
Connector Terminal Connector Terminal
E7 22RH E24 6
Ye s
LH E40 6
PKIA4603E
Te r m i n a l s
Continuity IPDM E/R Rear combination lamp
Connector Terminal Connector Terminal
E7 22RH T17 2
Ye s
LH T9 2
PKIA4604E
Te r m i n a l s
Continuity IPDM E/R Licence plat lamp
Connector Terminal Connector Terminal
E7 22RH T104 2
Ye s
LH T102 2
PKIA4605E

LT-124
PARKING, LICENSE PLATE AND TAIL LAMPS
Revision: 2006 November2007 350Z
9. CHECK GROUND
1. Check continuity between front combination lamp, rear combination lamp and license plate lamp harness
connector and ground.
OK or NG
OK >> Check bulb.
NG >> Repair harness or connector.
Parking, Side Marker, License Plate and Tail Lamps Do Not Turn OFF (After
Approx. 10 Minutes)
NKS004ZD
1. CHECK IPDM E/R
1. Turn ignition switch ON. Place combination switch (lighting switch) in the ON position. Turn ignition switch
OFF.
2. Make sure parking, license plate, and tail lamps turn OFF after approximately 10 minutes.
OK or NG
OK >> INSPECTION END.
NG >> Ignition relay malfunction. Refer to PG-17, "
Function of Detecting Ignition Relay Malfunction" .
Front combination lamp
connectorTerminal
GroundContinuity
RH E24
8Yes
LH E40
PKIC4877E
Rear combination lamp
connectorTerminal
GroundContinuity
RH T17
3Yes
LH T9
PKIA7183E
License plate lamp
connectorTerminal
GroundContinuity
RH T104
1Yes
LH T102
PKIA7185E

LT-128
INTERIOR ROOM LAMP
Revision: 2006 November2007 350Z
INTERIOR ROOM LAMPPFP:26410
Component Parts and Harness Connector LocationNKS004ZJ
System DescriptionNKS004ZK
When the map lamp switch is in the DOOR position, map lamp ON/OFF is controlled by timer according to sig-
nals from switches including key switch, door switch driver side and assist side, unlock and lock signal from
key fob, door lock and unlock switch, key cylinder lock and unlock switch, ignition switch.
When the map lamp turns ON, there is a gradual brightening over 1 second. When map lamp turns OFF, there
is a gradual dimming over 1 second.
Map lamp timer is controlled by BCM (body control module).
Map lamp timer control settings can be changed with CONSULT-III.
Ignition key hole illumination turns ON at time when driver door is opened (door switch ON) or removed key
fob from key cylinder. Illumination turns OFF when driver door is closed (door switch OFF).
PKID0829E