LT-154
INTERIOR ROOM LAMP
Revision: 2006 November2007 350Z
VANITY MIRROR LAMP
1. Insert a thin screwdriver in the lens end and remove lens.
2. Remove bulb.
3. Installation is the reverse order of removal.
LUGGAGE ROOM LAMP & TRUNK ROOM LAMP
Luggage Room Lamp (Coupe Models)
1. Remove luggage room lamp. Refer to LT- 1 5 5 , "Removal and Installation" .
2. Remove bulb.
3. Installation is the reverse order of removal.
Trunk Room Lamp (Roadster Models)
1. Unfold pawl A and remove lens.
2. Remove trunk room lamp while pressing pawl B in the direction
of the arrow.
3. Disconnect trunk room lamp connector.
4. Installation is the reverse order of removal.
IGNITION KEY HOLE ILLUMINATION
1. Remove instrument lower driver panel. Refer to IP-10,
"INSTRUMENT PANEL ASSEMBLY" .
2. Turn bulb socket to left to release lock and remove bulb socket
(1).
3. Remove ignition key illumination bulb (2) from its socket.
4. Installation is the reverse order of removal.Vanity mirror lamp : 12V - 1.32W
PKIA7806E
Luggage room lamp : 12V - 5W
PKIA1885E
Trunk room lamp : 12V - 3.4W
PKIA0182E
Ignition key hole illumination : 12V - 1.4W
PKIC4830J
LT-156
ILLUMINATION
Revision: 2006 November2007 350Z
ILLUMINATIONPFP:27545
System DescriptionNKS004ZY
Control of the illumination lamp operation is dependent upon the position of the lighting switch (combination
switch). When the lighting switch is placed in the 1ST or 2ND position, the BCM (body control module)
receives input signal requesting illumination lamps to illuminate. This input signal is communicated to the
IPDM E/R (intelligent power distribution module engine room) through the CAN communication lines. The
CPU (central processing unit) located in the IPDM E/R controls tail lamp relay coil. This relay, when energized,
directs power to illumination lamps, which then illuminate.
OUT LINE
Power is supplied at all times
through 10A fuse (No.71, located in IPDM E/R)
to tail lamp relay, located in IPDM E/R, and
to CPU located in IPDM E/R,
through 15A fuse (No.78, located in IPDM E/R)
to CPU located in IPDM E/R.
Power is also supplied at all times
through 40A fusible link (letter F, located in fuse, fusible link and relay box)
to BCM terminal 55,
through 10A fuse [No.18, located in fuse block (J/B)]
to BCM terminal 42,
through 10A fuse [No.19, located in fuse block (J/B)]
to unified meter and A/C amp. terminal 21,
through 10A fuse [No.19, located in fuse block (J/B)]
to combination meter terminal 24.
With ignition switch in the ON or START position, power is supplied
to CPU located in IPDM E/R,
through 10A fuse [No.1, located in fuse block (J/B)]
to BCM terminal 38,
through 10A fuse [No.12, located in fuse block (J/B)]
to unified meter and A/C amp. terminal 22, and
to NAVI control unit terminal 63 (With navigation system),
through 10A fuse [No.14, located in fuse block (J/B)]
to combination meter terminal 23.
With ignition switch in the ACC or ON position, power is supplied
through 10A fuse [No.6, located in fuse block (J/B)]
to BCM terminal 11.
Ground is supplied
to BCM terminal 52
through grounds M30 and M66,
to IPDM E/R terminals 38 and 60
through grounds E17, E43 and B102 (with VDC system, navigation system or telephone)
through grounds E17, E43 and F152 (without VDC system, navigation system and telephone),
to unified meter and A/C amp. terminals 29 and 30
through grounds M30 and M66,
to combination meter terminals 10, 11 and 12
through grounds M30 and M66,
to NAVI control unit terminal 1 (With navigation system)
through ground B115 (With navigation system).
LT-158
ILLUMINATION
Revision: 2006 November2007 350Z
EXTERIOR LAMP BATTERY SAVER CONTROL
When the combination switch (lighting switch) is in the 1ST or 2ND position, and the ignition switch is turned
from ON or ACC to OFF, battery saver control function is activated.
Under this condition, the illumination lamps remain illuminated for 5 minutes, then illumination lamps are
turned off.
When the lighting switch is turned from OFF to 1ST or 2ND position after illumination lamps are turned off by
battery saver control, and illumination lamps illuminate again.
Exterior lamp battery saver control mode can be changed by the function setting of CONSULT-III.
CAN Communication System DescriptionNKS004ZZ
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitNKS00500
Refer to LAN-48, "CAN System Specification Chart" .
LT-172
BULB SPECIFICATIONS
Revision: 2006 November2007 350Z
BULB SPECIFICATIONSPFP:26297
HeadlampNKS00505
Exterior LampNKS00506
Interior Lamp/IlluminationNKS00507
Item Wattage (W)
High / Low35 (D2R)
Item Wattage (W)
Front combination lampFront turn signal lamp/— 28/8 (amber)
Parking lamp 5
Front side marker lamp LED
Rear combination lampStop/Tail lamp LED
Rear turn signal lamp 21 (amber)
Back-up lamp 21
Rear side marker lamp LED
License plate lamp5
High-mounted stop lampLED
Item Wattage (W)
Luggage floor box lamp1.4
Cup holder illumination lamp1.1
Bottle holder illumination lampLED
Map lamp8
Luggage room lamp5
Trunk room lamp3.4
Vanity mirror lamp1.32
Ignition key hole illumination lamp1.4
