LT-154
INTERIOR ROOM LAMP
Revision: 2006 November2007 350Z
VANITY MIRROR LAMP
1. Insert a thin screwdriver in the lens end and remove lens.
2. Remove bulb.
3. Installation is the reverse order of removal.
LUGGAGE ROOM LAMP & TRUNK ROOM LAMP
Luggage Room Lamp (Coupe Models)
1. Remove luggage room lamp. Refer to LT- 1 5 5 , "Removal and Installation" .
2. Remove bulb.
3. Installation is the reverse order of removal.
Trunk Room Lamp (Roadster Models)
1. Unfold pawl A and remove lens.
2. Remove trunk room lamp while pressing pawl B in the direction
of the arrow.
3. Disconnect trunk room lamp connector.
4. Installation is the reverse order of removal.
IGNITION KEY HOLE ILLUMINATION
1. Remove instrument lower driver panel. Refer to IP-10,
"INSTRUMENT PANEL ASSEMBLY" .
2. Turn bulb socket to left to release lock and remove bulb socket
(1).
3. Remove ignition key illumination bulb (2) from its socket.
4. Installation is the reverse order of removal.Vanity mirror lamp : 12V - 1.32W
PKIA7806E
Luggage room lamp : 12V - 5W
PKIA1885E
Trunk room lamp : 12V - 3.4W
PKIA0182E
Ignition key hole illumination : 12V - 1.4W
PKIC4830J
LT-156
ILLUMINATION
Revision: 2006 November2007 350Z
ILLUMINATIONPFP:27545
System DescriptionNKS004ZY
Control of the illumination lamp operation is dependent upon the position of the lighting switch (combination
switch). When the lighting switch is placed in the 1ST or 2ND position, the BCM (body control module)
receives input signal requesting illumination lamps to illuminate. This input signal is communicated to the
IPDM E/R (intelligent power distribution module engine room) through the CAN communication lines. The
CPU (central processing unit) located in the IPDM E/R controls tail lamp relay coil. This relay, when energized,
directs power to illumination lamps, which then illuminate.
OUT LINE
Power is supplied at all times
through 10A fuse (No.71, located in IPDM E/R)
to tail lamp relay, located in IPDM E/R, and
to CPU located in IPDM E/R,
through 15A fuse (No.78, located in IPDM E/R)
to CPU located in IPDM E/R.
Power is also supplied at all times
through 40A fusible link (letter F, located in fuse, fusible link and relay box)
to BCM terminal 55,
through 10A fuse [No.18, located in fuse block (J/B)]
to BCM terminal 42,
through 10A fuse [No.19, located in fuse block (J/B)]
to unified meter and A/C amp. terminal 21,
through 10A fuse [No.19, located in fuse block (J/B)]
to combination meter terminal 24.
With ignition switch in the ON or START position, power is supplied
to CPU located in IPDM E/R,
through 10A fuse [No.1, located in fuse block (J/B)]
to BCM terminal 38,
through 10A fuse [No.12, located in fuse block (J/B)]
to unified meter and A/C amp. terminal 22, and
to NAVI control unit terminal 63 (With navigation system),
through 10A fuse [No.14, located in fuse block (J/B)]
to combination meter terminal 23.
With ignition switch in the ACC or ON position, power is supplied
through 10A fuse [No.6, located in fuse block (J/B)]
to BCM terminal 11.
Ground is supplied
to BCM terminal 52
through grounds M30 and M66,
to IPDM E/R terminals 38 and 60
through grounds E17, E43 and B102 (with VDC system, navigation system or telephone)
through grounds E17, E43 and F152 (without VDC system, navigation system and telephone),
to unified meter and A/C amp. terminals 29 and 30
through grounds M30 and M66,
to combination meter terminals 10, 11 and 12
through grounds M30 and M66,
to NAVI control unit terminal 1 (With navigation system)
through ground B115 (With navigation system).
ILLUMINATION
LT-171
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: 2006 November2007 350Z
Bulb ReplacementNKS00503
LUGGAGE FLOOR BOX LAMP
1. Remove luggage floor box lamp. Refer to
2. Turn bulb socket counterclockwise to release lock and remove
it.
3. Installation is the reverse order of removal.
CUP HOLDER ILLUMINATION
1. Remove center console assembly (1). Refer to IP-10, "INSTRU-
MENT PANEL ASSEMBLY" .
2. Turn bulb socket counterclockwise to release lock and remove
bulb socket (2).
3. Remove cup holder illumination bulb (3) from its socket.
4. Installation is the reverse order of removal.
Removal and InstallationNKS00504
LUGGAGE FLOOR BOX LAMP
1. Pull out rear floor box lamp using screwdriver or similar tool.
2. Installation is the reverse order of removal.Luggage floor box lamp : 12 V - 1.4W
PKIA1889E
Cup holder illumination : 12V - 1.1W
PKIC4811J
PKIA1888E
