2007 NISSAN 350Z steering wheel

BR-6
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
Revision: 2006 November2007 350Z
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTINGPFP:00003
NVH Troubleshooting ChartNFS00005
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×: ApplicableReference page
BR-29
, BR-31
, BR-42
, BR-45
BR-26
, BR-39
BR-27
, BR-40—
—
BR-35
, BR-37
, BR-48
, BR-50
—
—
—
BR-35
, BR-37
, BR-48
, BR-50
—
NVH in PR section
NHV in RFD section
NVH in FAX, RAX and FSU, RSU section
NVH in WT section
NVH in WT section
NVH in RAX section
NVH in PS section
Possible cause and
SUSPECTED PARTS
Pads - damaged
Pads - uneven wear
Shims damaged
Rotor imbalance
Rotor damage
Rotor runout
Rotor deformation
Rotor deflection
Rotor rust
Rotor thickness variation
Drum out of round
PROPELLER SHAFT
DIFFERENTIAL
AXLE AND SUSPENSION
TIRES
ROAD WHEEL
DRIVE SHAFT
STEERING
Symptom BRAKENoise××× ×× ×××
××
Shake× × ×××
××
Shimmy, Judder×××××××× ××× ×

FRONT DISC BRAKE
BR-31
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2006 November2007 350Z
2. Attach pad.
CAUTION:

Attach the pad with wear sensor to the outer side.

The side of the shim with the larger cutouts should be on
the entry side of the disc rotor spin.
3. Insert the upper pad pin from the inner cylinder side, then insert
firmly to the outer cylinder side through the hole in the top of the
pad.
4. As shown in the figure, place the top of the cross spring over the
top pad pin, press in the cross spring, push the lower pad pin
from the inner cylinder side to the outer cylinder side, and
secure the cross spring.
5. Insert the clip in the small hole at the end of the pad pin.
CAUTION:
If the clip is not fully attached, the pad pin or the pad could
fall out while the vehicle is in motion.
6. Install tires to vehicle.
Removal and Installation of Brake Caliper Assembly (Other than Brembo Cali-
pers)
NFS000AV
REMOVAL
1. Remove tires from vehicle with a power tool.
2. Fasten disc rotor using wheel nut.
3. Drain brake fluid gradually (from bleed valve while depressing brake pedal). Refer to BR-10, "
Drain and
Refill" .
4. Remove union bolt, and then remove brake hose from caliper
assembly.
5. Remove torque member mounting bolts (from torque member),
and remove caliper assembly (from vehicle with a power tool).
CAUTION:
Do not drop brake pad.
6. Remove disc rotor.
CAUTION:
Put matching marks on wheel hub assembly and disc rotor,
if it is necessary to remove disc rotor.
INSTALLATION
CAUTION:

Refill with new brake fluid “DOT 3”.

Do not reuse drained brake fluid.
1. Install disc rotor.
CAUTION:
Put alignment marks on disc rotor and wheel hub at the time of removal when reusing disc rotor.
2. Install caliper assembly to vehicle, and tighten torque member mounting bolts to the specified torque.
Refer to BR-27, "
Components" .
CAUTION:
Before installing torque member to vehicle, wipe oil and grease on washer seats on steering
knuckle and mounting surface of torque member.
PFIA0275E
PFIA0276E
SFIA0140E

FRONT DISC BRAKE
BR-35
C
D
E
G
H
I
J
K
L
MA
B
BR
Revision: 2006 November2007 350Z
5. Install the torque member to the steering knuckle and tighten the
mounting bolts to the specified torque. Refer to BR-27, "
Compo-
nents" .
CAUTION:
Before installing torque member to vehicle, wipe off oil and
grease on the washer seats on steering knuckle and the
mounting surface of the torque member.
6. Install pad retainers to torque member.
7. Press in piston until pads can be installed, and then install cylin-
der body to torque member.
8. Install cylinder body, and tighten sliding pin bolt to the specified
torque. Refer to BR-27, "
Components" .
9. Position a projection of brake hose metal fitting by aligning with protrusions on cylinder body and tighten
union bolt to specified torque. Refer to BR-12, "
Hydraulic Circuit" .
CAUTION:

Assemble brake hose securely to cylinder body.

Do not reuse copper washer for union bolts.
10. After installing caliper assembly, refill with new brake fluid and bleed air. Refer to BR-11, "
Bleeding Brake
System" .
DISC ROTOR INSPECTION
Visual Inspection
Check surfaces of disc rotor for uneven wear, cracks, and serious damage. If a malfunction is detected,
replace applicable part.
Runout Inspection
1. Using wheel nuts, secure disc rotor to wheels hub. (2 or more positions)
2. Using a dial indicator, check runout.
NOTE:
Make sure that wheel bearing axial end play is with in the speci-
fication before measuring runout. Refer to FA X - 4 , "
On-Vehicle
Inspection" .
3. If runout is outside limit, find the minimum runout point by shift-
ing the mounting positions of disc rotor and wheel hub by one hole.
4. If runout is still outside the limit after performing the above operation, replace or lathe the disc rotor.
[When lathing, use the Pro–Cut PFM On–Car Brake Lathe (Tool No. 38–PFM90.5) or equivalent.]
Thickness Inspection
Using a micrometer, check thickness of disc rotor. If thickness is out-
side standard, replace disc rotor.
SBR557E
Measurement point:
At a point 10.0 mm (0.394 in) from outer edge of disc
Runout limit (with it attached to the vehicle):
0.035 mm (0.0014 in) or less
SBR019B
Standard thickness : 28.0 mm (1.10 in)
Repair limit thickness : 26.0 mm (1.02 in)
Maximum uneven wear (measured at 8 positions)
: 0.015 mm (0,0006 in) or less
SBR020B